Lane Keeping System
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| B11C7:46 | High Beam Sensor: Calibration/Parameter Memory Failure | DIAGNOSE the automatic high beam feature. REFER to: Headlamps . |
| B11C7:97 | High Beam Sensor: Component or System Operation Obstructed or Blocked | DIAGNOSE the automatic high beam feature. REFER to: Headlamps . |
| B1286:14 | Interior Mirror: Circuit Short To Ground or Open | REFER to: Rear View Mirrors . |
| B12D8:11 | Mirror Heater Output: Circuit Short To Ground | GO to Pinpoint Test C |
| B12D8:13 | Mirror Heater Output: Circuit Open | GO to Pinpoint Test C |
| C1001:78 | Vision System Camera: Alignment or Adjustment Incorrect | This continuous memory DTC sets when a new IPMA has been installed without performing the camera alignment. PERFORM the camera alignment using a diagnostic scan tool. |
| U0100:87 | Lost Communication With ECM/PCM "A": Missing Message | GO to Pinpoint Test E |
| U0131:87 | Lost Communication With Power Steering Control Module: Missing Message | GO to Pinpoint Test F |
| U0140:87 | Lost Communication With Body Control Module: Missing Message | GO to Pinpoint Test G |
| U0151:87 | Lost Communication With Restraints Control Module: Missing Message | GO to Pinpoint Test H |
| U0155:87 | Lost Communication With Instrument Panel Cluster (IPC): Missing Message | GO to Pinpoint Test I |
| U0212:87 | Lost Communication With Steering Column Control Module: Missing Message | GO to Pinpoint Test J |
| U0401:00 | Invalid Data Received From ECM/PCM A: No Sub Type Information | RETRIEVE and FOLLOW non-network Diagnostic Trouble Codes (DTCs) from the PCM. Refer to the appropriate Engine article for the procedure. If no Diagnostic Trouble Codes (DTCs) are present in the PCM, DIAGNOSE the observable symptom. |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | This continuous memory DTC can set due to a fault in the BCM or an input to the BCM. RETRIEVE and FOLLOW non-network Diagnostic Trouble Codes (DTCs) from the BCM. REFER to: Body Control Module (BCM) . If no Diagnostic Trouble Codes (DTCs) are present in the BCM, DIAGNOSE the observable symptom. |
| U0423:00 | Invalid Data Received From Instrument Panel Cluster Control Module: No Sub Type Information | This continuous memory DTC can set due to a fault in the IPC or an input to the IPC. RETRIEVE and FOLLOW non-network Diagnostic Trouble Codes (DTCs) from the IPC. REFER to: Instrumentation, Message Center and Warning Chimes . If no Diagnostic Trouble Codes (DTCs) are present in the IPC, DIAGNOSE the observable symptom. |
| U0429:00 | Invalid Data Received From Steering Column Control Module: No Sub Type Information | This continuous memory DTC can set due to a fault in the SCCM or an input to the SCCM. RETRIEVE and FOLLOW non-network Diagnostic Trouble Codes (DTCs) from the SCCM. REFER to: Steering Wheel and Column Electrical Components . If no Diagnostic Trouble Codes (DTCs) are present in the SCCM, DIAGNOSE the observable symptom. |
| U0452:00 | Invalid Data Received From Restraints Control Module: No Sub Type Information | This continuous memory DTC can set due to a fault in the RCM or an input to the RCM. RETRIEVE and FOLLOW non-network Diagnostic Trouble Codes (DTCs) from the RCM. REFER to: Airbag Supplemental Restraint System (SRS) . If no Diagnostic Trouble Codes (DTCs) are present in the RCM, DIAGNOSE the observable symptom. |
| U1000:11 | Solid State Driver Protection Activated: Circuit Short To Ground | A continuous memory DTC that set when the IPMA has temporarily disabled the IPMA camera heated windshield element output because an excessive current draw exists (such as a short to ground). The IPMA cannot enable the output driver until the short is corrected. ADDRESS all other IPMA Diagnostic Trouble Codes (DTCs) first. After the cause of the concern is corrected, CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the IPMA self-test to enable the output driver. |
| U201A:54 | Control Module Main Calibration Data: Missing Calibration | CHECK the vehicle service history for recent service actions related to this module. This continuous memory DTC can set due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, INSTALL As-Built data from Professional Technician Society (PTS), following the diagnostic scan tool instructions under Module Programming>As-Built. REFER to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to: Interior Rear View Mirror . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CHECK the vehicle service history for recent service actions related to this module. This continuous memory DTC can set due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, INSTALL As-Built data from Professional Technician Society (PTS), following the diagnostic scan tool instructions under Module Programming>As-Built. REFER to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to: Interior Rear View Mirror . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | CHECK the vehicle service history for recent service actions related to this module. This continuous memory DTC can set due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, INSTALL As-Built data from Professional Technician Society (PTS), following the diagnostic scan tool instructions under Module Programming>As-Built. REFER to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to: Interior Rear View Mirror . |
| U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | CHECK the vehicle service history for recent service actions related to this module. This continuous memory DTC can set due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, INSTALL As-Built data from Professional Technician Society (PTS), following the diagnostic scan tool instructions under Module Programming>As-Built. REFER to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to: Interior Rear View Mirror . |
| U3000:42 | Control Module: General Memory Failure | ADDRESS all other IPMA Diagnostic Trouble Codes (DTCs) first. If this continuous memory DTC is still present after all other Diagnostic Trouble Codes (DTCs) have been addressed, INSTALL a new interior mirror. REFER to: Interior Rear View Mirror . |
| U3000:49 | Control Module: Internal Electronic Failure | The IPMA has permanently disabled the IPMA camera heated windshield element output because an excessive current draw has occurred more times than the module can withstand. ADDRESS all other IPMA Diagnostic Trouble Codes (DTCs). If this continuous memory DTC is still present after all other IPMA Diagnostic Trouble Codes (DTCs) have been addressed, INSTALL a new interior mirror. REFER to: Interior Rear View Mirror . |
| U3000:93 | Control Module: No Operation | ADDRESS all other IPMA Diagnostic Trouble Codes (DTCs). If this DTC is still present on-demand or in continuous memory after all other IPMA Diagnostic Trouble Codes (DTCs) have been addressed, INSTALL a new interior mirror. REFER to: Interior Rear View Mirror . |
| U3000:96 | Control Module: Component Internal Failure | ADDRESS all other IPMA Diagnostic Trouble Codes (DTCs). After all other IPMA Diagnostic Trouble Codes (DTCs) have been addressed, INSTALL a new interior mirror. REFER to: Interior Rear View Mirror . |