With Sync Without Touchscreen: APIM
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| B108E:02 | Display: General Signal Failure | GO to Pinpoint Test L |
| B108E:4A | Display: Incorrect Component Installed | An incorrect FCDIM is detected. REMOVE the incorrect FCDIM and INSTALL the correct FCDIM. REFER to: Front Control/Display Interface Module (FCDIM) . |
| B108E:4B | Display: Over Temperature | WAIT 10 minutes and allow the FCDIM to cool. CLEAR the DTC and REPEAT the self-test. If the DTC is retreived again, INSTALL a new FCDIM. REFER to: Front Control/Display Interface Module (FCDIM) . |
| B108E:87 | Display: Missing Message | GO to Pinpoint Test L |
| B119F:01 | GPS Antenna: General Electrical Failure | GO to Pinpoint Test R |
| B119F:13 | GPS Antenna: Circuit Open | GO to Pinpoint Test R |
| B1252:11 | USB Port: Circuit Short To Ground | GO to Pinpoint Test O |
| B1252:13 | USB Port: Circuit Open | GO to Pinpoint Test O |
| B14FD:11 | External Media Control Connectivity: Circuit Short To Ground | GO to Pinpoint Test O |
| B1D79:11 | Microphone Input: Circuit Short To Ground | GO to Pinpoint Test N |
| B1D79:12 | Microphone Input: Circuit Short To Battery | GO to Pinpoint Test N |
| B1D79:13 | Microphone Input: Circuit Open | GO to Pinpoint Test N |
| C1001:1 | Vision System Camera: General Electrical Failure | REFER to: Parking Aid . |
| U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | GO to Pinpoint Test T |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test U |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to Pinpoint Test V |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test W |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to Pinpoint Test X |
| U0232:00 | Lost Communication With Side Obstacle Detection Control Module - Left: No Sub Type Information | GO to Pinpoint Test Y |
| U0233:00 | Lost Communication With Side Obstacle Detection Control Module - Right: No Sub Type Information | GO to Pinpoint Test Z |
| U0256:00 | Lost Communication With Front Controls Interface Module "A": No Sub Type Information | GO to Pinpoint Test AB |
| U0415:00 | Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | DIAGNOSE any Diagnostic Trouble Codes (DTCs) present in the ABS module. REFER to: Anti-Lock Brake System (ABS) and Stability Control
. If no Diagnostic Trouble Codes (DTCs) are present in the ABS module, DIAGNOSE the observable symptom. If no symptoms are present, DISREGARD this DTC. |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | DIAGNOSE any Diagnostic Trouble Codes (DTCs) present in the BCM. REFER to: Body Control Module (BCM)
. If no Diagnostic Trouble Codes (DTCs) are present in the BCM, DIAGNOSE the observable symptom. If no symptoms are present, DISREGARD this If no symptoms are present, DISREGARD this DTC. |
| U0423:00 | Invalid Data Received From Instrument Panel Cluster Control Module: No Sub Type Information | DIAGNOSE any Diagnostic Trouble Codes (DTCs) present in the IPC. REFER to: Instrumentation, Message Center and Warning Chimes
. If no Diagnostic Trouble Codes (DTCs) are present in the IPC, DIAGNOSE the observable symptom. If no symptoms are present, DISREGARD this DTC. |
| U0452:00 | Invalid Data Received From Restraints Control Module: No Sub Type Information | DIAGNOSE any Diagnostic Trouble Codes (DTCs) present in the RCM. REFER to: Airbag Supplemental Restraint System (SRS) - Raptor
. REFER to: Airbag Supplemental Restraint System (SRS)
. If no Diagnostic Trouble Codes (DTCs) are present in the RCM, Diagnose the observable symptom. If no symptoms are present, DISREGARD this DTC. |
| U2017:45 | Control Module Software #2: Program Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds and then REPEAT the self-test. If the DTC is retrieved again, Refer to: APIM Hardware Testing . |
| U2017:51 | Control Module Software #2: Not Programmed | This DTC sets due to an incorrect or incomplete APIM configuration. Using a diagnostic scan tool, CARRY OUT the APIM programming procedure. REFER to: SYNC Module [APIM] Programming . |
| U2017:52 | Control Module Software #2: Not Activated | This DTC sets due to an incorrect or incomplete APIM configuration. Using a diagnostic scan tool, CARRY OUT the APIM programming procedure. REFER to: SYNC Module [APIM] Programming . |
| U2017:54 | Control Module Software #2: Missing Calibration | This DTC sets due to an incorrect or incomplete APIM configuration. Using a diagnostic scan tool, CARRY OUT the APIM programming procedure. REFER to: SYNC Module [APIM] Programming . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | This DTC sets due to an incorrect or incomplete APIM configuration. Using a diagnostic scan tool, CARRY OUT the APIM programming procedure. REFER to: SYNC Module [APIM] Programming . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | This DTC sets due to an incorrect or incomplete APIM configuration. Using a diagnostic scan tool, CARRY OUT the APIM programming procedure. REFER to: SYNC Module [APIM] Programming . |
| U3000:04 | Control Module: System Internal Failure | CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds and then REPEAT the self-test. If the DTC is retrieved again, Refer to: APIM Hardware Testing . |
| U3000:09 | Control Module: Component Failure | CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds and then REPEAT the self-test. If the DTC is retrieved again, Refer to: APIM Hardware Testing . |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds and then REPEAT the self-test. If the DTC is retrieved again, Refer to: APIM Hardware Testing . |
| U3000:88 | Control Module: Bus Off |
NOTE:
The module was unable to communicate on the network at a point in time. The fault is not currently present since the module had to communicate with the diagnostic scan tool to report this DTC. INSPECT for damaged or corroded wiring at the APIM. Refer to Module Communications Network
for schematic and connector information. CLEAR the DTC. WAIT at least 10 seconds and then REPEAT the self-test. If the DTC is retrieved again, Refer to: APIM Hardware Testing
. |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AC |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AD |