Network Message Chart
WARNING: This page is about a different car, the 2018 Lincoln Navigator. However, it is still accessible from the selected car via links, so may be relevant.
IPC Network Input Messages
| Broadcast Message | Originating Module | Message Purpose |
|---|---|---|
| BLIS trailer tow left status | SODL | Used to control the BLISRTT indicator and trailer blind spot information message center displays. |
| BLIS trailer tow right status | SODR | |
| Cross traffic alert left status | SODL | Used to control the CTA audio chime and the BLIS off RTT. |
| Cross traffic alert right status | SODR | |
| Side obstacle sensor status - left | SODL | Used to communicate the operating status of the SODL and to command the BLIS/ CTA message center displays. |
| Side obstacle sensor status - right | SODR | Used to communicate the operating status of the SODR and to command the BLIS/ CTA message center displays. |
HUD Network Input Messages
| Broadcast Message | Originating Module | Message Purpose |
|---|---|---|
| Cross traffic alert left status | SODL | Used to control the CTAHUD functions |
| Cross traffic alert right status | SODR | |
| Side obstacle sensor status - left | SODL | Used to communicate the operating status of the SODL and to command the BLIS/ HUD alert. |
| Side obstacle sensor status - right | SODR | Used to communicate the operating status of the SODR and to command the BLIS/ HUD alert. |
ACM Network Input Messages
| Broadcast Message | Originating Module | Message Purpose |
|---|---|---|
| Chime source | IPC | Used to command the audio chimes on vehicles without touchscreen. |
DSP Network Input Messages
| Broadcast Message | Originating Module | Message Purpose |
|---|---|---|
| Chime source | IPC | Used to command the audio chimes on vehicles with touchscreen. |
DDM Network Input Messages
| Broadcast Message | Originating Module | Message Purpose |
|---|---|---|
| Cross traffic alert left status | SODL | Used to command the LHBLIS®/ CTALED on and off. |
| Side obstacle sensor status-left | SODL | Used to command the LHBLIS®/ CTALED on and off. |
| Side detect left illumination | SODL | Used to command the LHBLIS®/ CTALED brightness level. |
PDM Network Input Messages
| Broadcast Message | Originating Module | Message Purpose |
|---|---|---|
| Cross traffic alert right status | SODR | Used to command the RHBLIS®/ CTALED on and off. |
| Side obstacle sensor status-right | SODR | Used to command the RHBLIS®/ CTALED on and off. |
| Side detect right illumination | SODR | Used to command the RHBLIS®/ CTALED brightness level. |
SODL Network Input Messages
| Broadcast Message | Originating Module | Message Purpose |
|---|---|---|
| BLIS® LED status driver side | DDM | Used to confirm the operating status of the LH exterior mirror BLIS® LED. |
| Vehicle configuration data | BCM | Used to enable/disable the BLIS® or CTA based on driver input. |
| Ignition key type | BCM | Used to disable the ability to turn off the BLIS® and CTA when a MyKey® restricted key is in use. |
| Gear lever position | PCM | Used to turn the BLIS® and CTA system on and off depending the gear lever position. |
| Wiper front status | SCCM | Used to determine ambient weather conditions for correct system operation. |
| Turn signal switch status | SCCM | Used to generate the secondary flashing LED alert when a turn signal is activated. |
| Trailer lamp connected | TRM | Disables the BLIS® and CTA when a trailer is electrically connected to the vehicle. |
| Vehicle speed | PCM | The vehicle speed input is used to turn the BLIS® on above 10 km/h (6 mph). |
SODR Network Input Messages
| Broadcast Message | Originating Module | Message Purpose |
|---|---|---|
| BLIS® LED status passenger side | PDM | Used to confirm the operating status of the RH exterior mirror BLIS®) LED. |
| Vehicle configuration data | BCM | Used to enable/disable the BLIS® or CTA based on driver input. |
| Ignition key type | BCM | Used to disable the ability to turn off the BLIS® and CTA when a MyKey® restricted key is in use. |
| Gear lever position | PCM | Used to turn the BLIS® and CTA system on and off depending the gear lever position. |
| Wiper front status | SCCM | Used to determine ambient weather conditions for correct system operation. |
| Turn signal switch status | SCCM | Used to generate the secondary flashing LED alert when a turn signal is activated. |
| Trailer lamp connected | TRM | Disables the BLIS® and CTA when a trailer is electrically connected to the vehicle. |
| Vehicle speed | PCM | The vehicle speed input is used to turn the BLIS® on above 10 km/h (6 mph). |