Side And Rear Vision System DTCS

Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .

DTC INDEX

DTC	Description	Action
B11D6:11	Driver Display Alert LED: Circuit Short To Ground	GO to Pinpoint Test D
B11D6:15	Driver Display Alert LED: Circuit Short To Battery or Open	If the LH or RH Blind Spot Information System (BLIS®)/Cross Traffic Alert (CTA) LED is inoperative, GO to Pinpoint Test D If the LH or RH Blind Spot Information System (BLIS®)/Cross Traffic Alert (CTA) LED is always on, GO to Pinpoint Test C
U0100:00	Lost Communication With ECM/PCM "A": No Sub Type Information	GO to Pinpoint Test G
U0101:00	Lost Communication with TCM: No Sub Type Information	GO to Pinpoint Test H
U0146:00	Lost Communication with Gateway "A": No Sub Type Information	GO to Pinpoint Test I
U0401:86	Invalid Data Received from ECM/PCM A: Signal Invalid	This DTC sets when the SODL or SODR receives invalid network data from the PCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. If no PCM Diagnostic Trouble Codes (DTCs) exist, DIAGNOSE the observable symptom.
U0402:86	Invalid Data Received from TCM: Signal Invalid	This DTC sets when the SODL or SODR receives invalid network data from the PCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. If no PCM Diagnostic Trouble Codes (DTCs) exist, DIAGNOSE the observable symptom.
U2100:00	Initial Configuration Not Complete: No Sub Type Information	This DTC sets due to incomplete or incorrect PMI procedures. CHECK the vehicle service history for recent service actions related to this module. If there have been recent service actions with this module, INSTALL as-built data from Professional Technician Society (PTS) following diagnostic scan tool instructions under Module Programming>As-Built. REFER to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to: Side Obstacle Detection Control Module .
U2300:55	Central Configuration: Not Configured	This DTC sets when the SODL or SODR do not detect the VIN information on the MS-CAN. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in all other modules.
U3000:44	Control Module: Data Memory Failure	CLEAR the SODL or SODR Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If DTC U3000:44 returns, INSTALL a new SODL or SODR. REFER to: Side Obstacle Detection Control Module .
U3000:45	Control Module: Program Memory Failure	CLEAR the SODL or SODR Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If DTC U3000:45 returns, INSTALL a new SODL or SODR. REFER to: Side Obstacle Detection Control Module .
U3000:46	Control Module: Calibration/Parameter Memory Failure	CLEAR the SODL or SODR Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If DTC U3000:46 returns, INSTALL a new SODL or SODR. REFER to: Side Obstacle Detection Control Module .
U3000:49	Control Module: Internal Electronic Failure	CLEAR the SODL or SODR Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If DTC U3000:49 returns, INSTALL a new SODL or SODR. REFER to: Side Obstacle Detection Control Module .
U3002:62	Vehicle Identification Number: Signal Compare Failure	This DTC sets when the VIN stored in the SODL or SODR does not match the VIN that is broadcast on the network. CHECK the vehicle service history for recent service actions related to this module. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the diagnostic scan tool. REFER to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to: Side Obstacle Detection Control Module .