Common Specifications & Procedures
TRANSIT CONNECT COMMON SPECIFICATIONS & PROCEDURES
| System | Specification/Procedure | |||
|---|---|---|---|---|
| Air Conditioning | ||||
| Service | SPECIFICATIONS | |||
| Torque | TORQUE SPECIFICATIONS | |||
| Axle Nut/Hub Nut | 81 lb.ft (110 Nm) | |||
| Battery | BATTERY - 2.5L DURATEC (125KW/170PS) | |||
| Brakes | ||||
| Bleeding Sequence | BRAKE SYSTEM PRESSURE BLEEDING | |||
| Front Disc Brakes w/Torque | Refer to appropriate component in REMOVAL AND INSTALLATION | |||
| Rear Disc Brakes w/Torque | Refer to appropriate component in REMOVAL AND INSTALLATION | |||
| Charging | ||||
| Generator w/Torque | ||||
| 2.5L Duratec | For removal and installation, refer to GENERATOR - 2.5L DURATEC (125KW/170PS) Upper Generator Bolt: 18 lb.ft (25 Nm) Lower Generator Bolts: 18 lb.ft (25 Nm) |
|||
| Drive Belts | ||||
| Adjustment | ACCESSORY DRIVE | |||
| Belt Routing | ACCESSORY DRIVE - COMPONENT LOCATION . | |||
| Engine Cooling | ||||
| General Service Specifications | SPECIFICATIONS | |||
| Radiator Cap Pressure | N/A | |||
| Thermostat R & I | THERMOSTAT . | |||
| Water Pump R & I | COOLANT PUMP | |||
| Engine Mechanical | ||||
| Compression | SPECIFICATIONS | |||
| Oil pressure (hot @ 2, 000 rpm) | 200-414 kPa (29.0-60 psi) | |||
| Overhaul | SPECIFICATIONS | |||
| Torque | Refer to appropriate component in REMOVAL AND INSTALLATION | |||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | |||
| Flywheel/Flex Plate Torque | ||||
| 2.5L Duratec | For tightening sequence, refer to FLEXPLATE
. Stage 1: 37 lb.ft (50 Nm) Stage 2: 59 lb.ft (80 Nm) Stage 3: 83 lb.ft (112 Nm) |
|||
| Fuel System | ||||
| Fuel Filter Location | Located in fuel tank as part of the fuel pump module. | |||
| Fuel Filter R & I | FUEL PUMP AND SENDER UNIT | |||
| Pressure Release Procedure | FUEL SYSTEM PRESSURE RELEASE | |||
| Fuel Pressure Test Procedure | FUEL SYSTEM PRESSURE CHECK | |||
| Ignition | ||||
| Firing Order & Cylinder Identification | 1-3-4-2 FIRING ORDER & CYLINDER IDENTIFICATION |
|||
| Ignition Wires (Routing) | Engine has coil-on-plug ignition. | |||
| Spark Plug | ||||
| 2.5L Duratec | ||||
| Type | AYFS 32Y R | |||
| Gap | 0.051 in (1.3 mm) | |||
| Torque | 106 lb.in (12 Nm) | |||
| Starting | ||||
| Starter | SPECIFICATIONS | |||
| Torque | ||||
| For removal and installation, refer to STARTER MOTOR . | Starter Motor Studbolts: 26 lb.ft (35 Nm) | |||
| Wheel Alignment | ||||
| Adjustment Specifications | SPECIFICATIONS | |||
| Torque | Refer to the appropriate procedure in GENERAL PROCEDURES | |||
| Wheel & Tire | ||||
| Wheel Lug Nut Torque | For tightening sequence, refer to WHEEL AND TIRE
. 111 lb.ft (150 Nm) |
|||