Common Specifications & Procedures
EXPEDITION COMMON SPECIFICATIONS & PROCEDURES
| System | Specification/Procedure | |||
|---|---|---|---|---|
| Air Conditioning | ||||
| Service | SPECIFICATIONS | |||
| Torque | Refer to the appropriate component in REMOVAL AND INSTALLATION | |||
| Axle Nut/Hub Nut | ||||
| Torque | 30 lb.ft (40 Nm) | |||
| Battery | ||||
| SPECIFICATIONS | ||||
| Brakes | ||||
| Bleeding Sequence | Brake System Pressure Bleeding . | |||
| Disc Brakes | ||||
| Front w/Torque | Refer to the specific component in REMOVAL AND INSTALLATION | |||
| Rear w/Torque | Refer to the specific component in REMOVAL AND INSTALLATION . | |||
| Charging | ||||
| Generator w/Torque | ||||
| Generator Stud Nut | 35 lb.ft (47 Nm) | |||
| Generator Bolt | 35 lb.ft (47 Nm) | |||
| Generator Stud | 71 lb.in (8 Nm) | |||
| Adjustment | Accessory Drive Belt | |||
| Belt Routing | Accessory Drive - Component Location | |||
| Engine Cooling | ||||
| Expedition | ||||
| General Service Specifications | SPECIFICATIONS | |||
| Radiator Cap Pressure | 21 psi (145 kPa) | |||
| Thermostat R & I | Thermostat and Thermostat Housing | |||
| Water Pump R & I | Coolant Pump . | |||
| Engine Mechanical | ||||
| 3.5L EcoBoost | ||||
| Compression | SPECIFICATIONS . | |||
| Oil pressure @ 1, 500 rpm with engine at normal operating temperature (High mode) | 30.0 psi (206.8 kPa) | |||
| Oil pressure @ 1, 500 rpm with engine at normal operating temperature (Low mode) | 20.0 psi (138 kPa) | |||
| Overhaul | SPECIFICATIONS | |||
| Torque | REMOVAL AND INSTALLATION | |||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | |||
| Flywheel/Flex Plate Torque | ||||
| For sequence refer to Flexplate 59 Ft. Lbs. (80 Nm) |
||||
| Fuel System | ||||
| Fuel Filter Location | The fuel tank(s) has a fuel filter that is part of the Fuel Pump (FP) module and cannot be serviced separately from the FP module | |||
| Fuel Filter R & I | Fuel Filter | |||
| Pressure Release Procedure | Fuel System Pressure Release | |||
| Pressure Specification | Engine Running 44 -73 psi (300 -500 kPa) |
|||
| Fuel Pressure Test Procedure | Fuel System Pressure Check . | |||
| Ignition | ||||
| Ignition Wires | Engine has coil-on-plug ignition. | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | |||
| Spark Plugs | ||||
| 3.5L GTDI | ||||
| Type | CYF-S 12Y PCT | |||
| Gap | 0.030 in (.75 mm) | |||
| Torque | 15 Nm (133 lb-in) | |||
| Starting | ||||
| Starter w/Torque | 48 Nm (35 lb-ft) | |||
| Wheel Alignment | ||||
| Adjustment Specifications | SPECIFICATIONS | |||
| Torque | Refer to the appropriate procedure in GENERAL PROCEDURES . | |||
| Wheel & Tire | ||||
| Wheel Lug Nut Torque | 150 Ft. Lbs. (204 N.m) | |||