Pinpoint Test I : U0200:87
WARNING: This page is about a different car, the 2019 Ford F-550 Super Duty, 2019 Ford F-450 Super Duty, 2019 Ford F-350 Super Duty, and 2019 Ford F-250 Super Duty. However, it is still accessible from the selected car via links, so may be relevant.
NOTE:
If new modules were installed prior to the DTC being set, the module configuration may be incorrectly set during the PMI or the PMI may not have been carried out.
- I1 CHECK THE COMMUNICATION NETWORK
- Using a diagnostic scan tool, perform a network test.
Does the PDM pass the network test?
Yes GO to I2 No DIAGNOSE no communication with the PDM. REFER to: Communications Network . - I2 CHECK THE BCM (BODY CONTROL MODULE) CONTINUOUS MEMORY DIAGNOSTIC TROUBLE CODES (CMDTCS)
- Using a diagnostic scan tool, clear the Diagnostic Trouble Codes (DTCs).
- Wait 10 seconds.
- Using a diagnostic scan tool, check the BCM Continuous Memory Diagnostic Trouble Codes (CM DTCs).
Is DTC U3006:16, U3006:17, U3007:16, U3007:17, U3013:16, U3013:17, U3014:16 or U3014:17 recorded?
Yes For DTC U3006:16, U3007:16, U3013:16 or U3014:16, GO to Pinpoint Test K For DTC U3006:17, U3007:17, U3013:17 or U3014:17, GO to Pinpoint Test L No GO to I3 - I3 RETRIEVE THE PDM (PASSENGER DOOR MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)
- Using a diagnostic scan tool, perform the PDM self-test.
Are any Diagnostic Trouble Codes (DTCs) recorded?
Yes REFER to: Locks, Latches and Entry Systems . No GO to I4 - I4 RECHECK THE BCM (BODY CONTROL MODULE) CONTINUOUS MEMORY DIAGNOSTIC TROUBLE CODES (CMDTCS)
- Using a diagnostic scan tool, clear the Diagnostic Trouble Codes (DTCs).
- Wait 10 seconds.
- Using a diagnostic scan tool, check the BCM Continuous Memory Diagnostic Trouble Codes (CM DTCs).
Is DTC U0200:87 still present?
Yes GO to I5 No The system is operating correctly at this time. The DTC may have been set due to high network traffic or an intermittent fault condition. - I5 CHECK FOR DTC (DIAGNOSTIC TROUBLE CODE) U0200:87 SET IN OTHER MODULES
- Using a diagnostic scan tool, clear the Diagnostic Trouble Codes (DTCs).
- Ignition OFF.
- Ignition ON.
- Wait 10 seconds.
- Using a diagnostic scan tool, retrieve all Continuous Memory Diagnostic Trouble Codes (CM DTCs).
Is DTC U0200:87 set in other modules?
Yes GO to I6 No GO to I7 - I6 CHECK FOR CORRECT PDM (PASSENGER DOOR MODULE) OPERATION
- Disconnect and inspect the PDM connectors.
- Repair:
- corrosion (install new connector or terminals - clean module pins)
- damaged or bent pins - install new terminals/pins
- pushed-out pins - install new pins as necessary
- Reconnect the PDM connectors. Make sure they seat and latch correctly.
- Operate the system and determine if the concern is still present.
Is the concern still present?
Yes CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, INSTALL a new PDM. REFER to: Passenger Door Module (PDM) . No The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues. - I7 CHECK FOR CORRECT BCM (BODY CONTROL MODULE) OPERATION
- Disconnect and inspect the BCM connectors.
- Repair:
- corrosion (install new connector or terminals - clean module pins)
- damaged or bent pins - install new terminals/pins
- pushed-out pins - install new pins as necessary
- Reconnect the BCM connectors. Make sure they seat and latch correctly.
- Operate the system and determine if the concern is still present.
Is the concern still present?
Yes CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, Refer to BCM Guided Routine . No The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.