Network Message Chart
WARNING: This page is about a different car, the 2020 Ford Mustang. However, it is still accessible from the selected car via links, so may be relevant.
IPC Network Input Messages
| Broadcast Message | Originating Module | Message Purpose |
|---|---|---|
| Side obstacle sensor status - left | SODL | Used to communicate the operating status of the SODL and to command the Cross Traffic Alert (CTA) message center displays. |
| Side obstacle sensor status - right | SODR | Used to communicate the operating status of the SODR and to command the Cross Traffic Alert (CTA) message center displays. |
| Cross traffic alert left status | SODL | Used to command the Cross Traffic Alert (CTA) audio chime and the BLIS® RTT. |
| Cross traffic alert right status | SODR |
ACM Network Input Messages
| Broadcast Message | Originating Module | Message Purpose |
|---|---|---|
| Chime mode | IPC | Used to command the Cross Traffic Alert (CTA) audio chimes on without touchscreen. |
DSP Network Input Messages
| Broadcast Message | Originating Module | Message Purpose |
|---|---|---|
| Chime mode | IPC | Used to command the Cross Traffic Alert (CTA) audio chimes on vehicles with touchscreen. |
SODL Network Input Messages
| Broadcast Message | Originating Module | Message Purpose |
|---|---|---|
| Blind Spot Information System (BLIS®)Cross Traffic Alert (CTA) enable command | IPC | Used to enable/disable the Blind Spot Information System (BLIS®) or Cross Traffic Alert (CTA) based on driver input. |
| Ignition key type | BCM | Used to disable the ability to turn OFF the Blind Spot Information System (BLIS®) and Cross Traffic Alert (CTA) when a MyKey restricted key is in use. |
| Gear lever position (automatic transmission vehicles only) | PCM | Used to turn the Blind Spot Information System (BLIS®) and Cross Traffic Alert (CTA) system on and off depending the gear lever position. |
| Reverse gear (manual transmission vehicles only) | PCM | Used to turn the Cross Traffic Alert (CTA) system on and off when the transmission is shifted in to and out of REVERSE (R). |
| Vehicle speed | PCM | Used to activate the Blind Spot Information System (BLIS®) after an ignition cycle and deactivate the Cross Traffic Alert (CTA) system when the vehicle speed exceeds preset thresholds. |
| Wiper status | SCCM | Used to determine ambient weather conditions for correct system operation. |
| Turn signal status | SCCM | Used to generate the secondary alert when a turn signal is activated. |
| VIN information | BCM | Contains VIN information. |
SODR Network Input Messages
| Broadcast Message | Originating Module | Message Purpose |
|---|---|---|
| Blind Spot Information System (BLIS®)Cross Traffic Alert (CTA) enable command | IPC | Used to enable/disable the Blind Spot Information System (BLIS®) or Cross Traffic Alert (CTA) based on driver input. |
| Gear lever position (automatic transmission vehicles only) | PCM | Used to turn the Blind Spot Information System (BLIS®) and Cross Traffic Alert (CTA) system on and off depending the gear lever position. |
| Reverse gear (manual transmission vehicles only) | PCM | Used to turn the Cross Traffic Alert (CTA) system on and off when the transmission is shifted in to and out of REVERSE (R). |
| Ignition key type | BCM | Used to disable the ability to turn OFF the Blind Spot Information System (BLIS®) and Cross Traffic Alert (CTA) when a MyKey® restricted key is in use. |
| Vehicle speed | PCM | Used to activate the Blind Spot Information System (BLIS®) after an ignition cycle and deactivate the Cross Traffic Alert (CTA) system when the vehicle speed exceeds preset thresholds. |
| Wiper status | SCCM | Used to determine ambient weather conditions for correct system operation. |
| Turn signal status | SCCM | Used to generate the secondary alert when a turn signal is activated. |
| VIN information | BCM | Contains VIN information. |