Steering Column DTCS: DSM
| DTC | Description | Action |
|---|---|---|
| B1298:24 | Steering Column Adjust Up Switch: Signal Stuck High |
NOTE:
The SCCM continually monitors the steering column control switch input. With battery voltage between 10 and 15.5 volts and with the ignition set to ON, if the SCCM receives switch input for more than 2 minutes, a DTC is set. INSTALL a new steering column control switch. REFER to: Steering Column Control Switch
.
CLEAR the SCCM and DSM Diagnostic Trouble Codes (DTCs). Using a diagnostic scan tool, CARRY OUT a SCCM self-test. If DTC B1298:24 returns, INSTALL a new SCCM. REFER to: Steering Column Control Module (SCCM)
. |
| B1299:24 | Steering Column Adjust Down Switch: Signal Stuck High |
NOTE:
The SCCM continually monitors the steering column control switch input. With battery voltage between 10 and 15.5 volts and with the ignition set to ON, if the SCCM receives switch input for more than 2 minutes, a DTC is set. INSTALL a new steering column control switch. REFER to: Steering Column Control Switch
.
CLEAR the SCCM and DSM Diagnostic Trouble Codes (DTCs). Using a diagnostic scan tool, CARRY OUT a SCCM self-test. If DTC B1299:24 returns, INSTALL a new SCCM. REFER to: Steering Column Control Module (SCCM)
. |
| B12A1:24 | Steering Column Adjust Out Switch: Signal Stuck High |
NOTE:
The SCCM continually monitors the steering column control switch input. With battery voltage between 10 and 15.5 volts and with the ignition set to ON, if the SCCM receives switch input for more than 2 minutes, a DTC is set. INSTALL a new steering column control switch. REFER to: Steering Column Control Switch
.
CLEAR the SCCM and DSM Diagnostic Trouble Codes (DTCs). Using a diagnostic scan tool, CARRY OUT a SCCM self-test. If DTC B12A1:24 returns, INSTALL a new SCCM. REFER to: Steering Column Control Module (SCCM)
. |
| B12A2:24 | Steering Column Adjust In Switch: Signal Stuck High |
NOTE:
The SCCM continually monitors the steering column control switch input. With battery voltage between 10 and 15.5 volts and with the ignition set to ON, if the SCCM receives switch input for more than 2 minutes, a DTC is set. INSTALL a new steering column control switch. REFER to: Steering Column Control Switch
.
CLEAR the SCCM and DSM Diagnostic Trouble Codes (DTCs). Using a diagnostic scan tool, CARRY OUT a SCCM self-test. If DTC B12A2:24 returns, INSTALL a new SCCM. REFER to: Steering Column Control Module (SCCM)
. |
| B12A7:11 | Steering Column Tilt Sensor A: Circuit Short To Ground | GO to Pinpoint Test C |
| B12A7:12 | Steering Column Tilt Sensor A: Circuit Short To Battery | GO to Pinpoint Test C |
| B12A8:11 | Steering Column Telescope Sensor A: Circuit Short To Ground | GO to Pinpoint Test C |
| B12A8:12 | Steering Column Telescope Sensor A: Circuit Short To Battery | GO to Pinpoint Test C |
| B1375:09 | Steering Column Tilt Motor: Component Failure | GO to Pinpoint Test D |
| B1375:11 | Steering Column Tilt Motor: Circuit Short To Ground | GO to Pinpoint Test D |
| B1375:12 | Steering Column Tilt Motor: Circuit Short To Battery | GO to Pinpoint Test D |
| B1375:13 | Steering Column Tilt Motor: Circuit Open | GO to Pinpoint Test D |
| B1375:1A | Steering Column Tilt Motor Circuit Resistance Below Threshold | GO to Pinpoint Test D |
| B1375:31 | Steering Column Tilt Motor: No Signal | GO to Pinpoint Test C |
| B137E:09 | Steering Column Telescope Motor: Component Failure | GO to Pinpoint Test D |
| B137E:11 | Steering Column Telescope Motor: Circuit Short To Ground | GO to Pinpoint Test D |
| B137E:12 | Steering Column Telescope Motor: Circuit Short To Battery | GO to Pinpoint Test D |
| B137E:13 | Steering Column Telescope Motor: Circuit Open | GO to Pinpoint Test D |
| B137E:1A | Steering Column Telescope Motor: Circuit Resistance Below Threshold | GO to Pinpoint Test D |
| B137E:31 | Steering Column Telescope Motor: No Signal | GO to Pinpoint Test C |
| All other DSM Diagnostic Trouble Codes (DTCs) | -- | REFER to: Front Seats . |