LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Ford >> 2020 >> Fusion S >> Repair and Diagnosis >> External Pages >> Different car >> Section 34 (Climate Control System - General Information) >> Diagnosis And Testing >> Climate Control System - Vehicles With: Electronic Manual Temperature Control (EMTC) >> Pinpoint Test(s) >> Pinpoint Test N : P193E >> Pinpoint Test N : P193E
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Pinpoint Test N : P193E

WARNING: This page is about a different car, the 2018 Ford F-550 Super Duty, 2018 Ford F-450 Super Duty, 2018 Ford F-350 Super Duty, and 2018 Ford F-250 Super Duty. However, it is still accessible from the selected car via links, so may be relevant.

  1. N1 VERIFY THE CUSTOMER CONCERN

    • Ignition ON.

    • Verify there is an observable symptom present.

    Is an observable symptom present? 

    Yes  GO to  N2
    No  The system is operating correctly at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.

  2. N2 CHECK THE COMMUNICATION NETWORK

    • Using a diagnostic scan tool, carry out the Network Test.

    Do the BCM, PCM and the FCIM pass the Network Test? 

    Yes  GO to  N3
    No  DIAGNOSE the BCM, PCM or FCIM does not communicate with the diagnostic scan tool. Refer to: Communications Network .

  3. N3 CHECK THE PCM (POWERTRAIN CONTROL MODULE) A/C (AIR CONDITIONING) REQUEST SIGNAL (AC_REQ) PID (PARAMETER IDENTIFICATION)

    • Start the engine.

    • Using a diagnostic scan tool, monitor the PCM AC_REQ PID.

    • On the HVAC controls, select PANEL mode, then press the A/C button (indicator ON).

    Does the AC_REQ PID display YES or On when the A/C button indicator is illuminated? 

    Yes  GO to  N7
    No  GO to  N4

  4. N4 CHECK THE FCIM (FRONT CONTROLS INTERFACE MODULE) A/C (AIR CONDITIONING) SWITCH (CC_SW_AC) PID (PARAMETER IDENTIFICATION)

    • Using a diagnostic scan tool, monitor the FCIM CC_SW_AC PID while pressing and releasing the A/C button.

    Does the PID display Active or On when the A/C button indicator is illuminated? 

    Yes  GO to  N6
    No  GO to  N5

  5. N5 CHECK FOR CORRECT FCIM (FRONT CONTROLS INTERFACE MODULE) OPERATION

    • Ignition OFF.

    • Disconnect and inspect all FCIM connectors.

    • Repair:

      • corrosion (install new connector or terminals - clean module pins)
      • damaged or bent pins - install new terminals/pins
      • pushed-out pins - install new pins as necessary

    • Reconnect all FCIM connectors. Make sure they seat and latch correctly.

    • Operate the system and determine if the concern is still present.

    Is the concern still present? 

    Yes  CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, Refer to FCIM HARDWARE TESTING .
    No  The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.

  6. N6 VERIFY CORRECT BCM (BODY CONTROL MODULE) OPERATION

    • Ignition OFF.

    • Disconnect and inspect all BCM electrical connectors.

    • Repair:

      • corrosion (install new connector or terminals - clean module pins)
      • damaged or bent pins - install new terminals/pins
      • pushed-out pins - install new pins as necessary

    • Reconnect all BCM electrical connectors. Make sure they seat and latch correctly.

    • Operate the system and determine if the concern is still present.

    Is the concern still present? 

    Yes  CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW the TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, Refer to BCM Hardware Testing .
    No  The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.

  7. N7 VERIFY CORRECT PCM (POWERTRAIN CONTROL MODULE) OPERATION

    • Ignition OFF.

    • Disconnect and inspect all PCM electrical connectors.

    • Repair:

      • corrosion (install new connector or terminals - clean module pins)
      • damaged or bent pins - install new terminals/pins
      • pushed-out pins - install new pins as necessary

    • Reconnect all PCM electrical connectors. Make sure they seat and latch correctly.

    • Operate the system and determine if the concern is still present.

    Is the concern still present? 

    Yes  CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, INSTALL a new PCM. Refer to: Powertrain Control Module (PCM) - 6.2L V8 . Refer to: Powertrain Control Module (PCM) - 6.8L Triton-30V - V10 . Refer to: Powertrain Control Module (PCM) - 6.7L Power Stroke Diesel .
    No  The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.
scientia non olet · About LEMON Manuals