LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Ford >> 2020 >> Fusion Titanium, AWD >> Repair and Diagnosis (Single Page) >> External Pages >> Different car >> Section 565 (Module Communications Network) >> Diagnosis And Testing >> Communications Network >> Pinpoint Tests >> Pinpoint Test S : The Power Steering Control Module (PSCM) Does Not Respond To The Diagnostic Scan Tool
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Pinpoint Test S : The Power Steering Control Module (PSCM) Does Not Respond To The Diagnostic Scan Tool

WARNING: This page is about a different car, the 2020 Ford Transit Connect. However, it is still accessible from the selected car via links, so may be relevant.
  1. Refer to Module Communications Network for schematic and connector information. Refer to Power Steering Controls for schematic and connector information.

    Normal Operation and Fault Conditions 

    The PSCM communicates on the HS-CAN2. REFER to: Communications Network - System Operation and Component Description .

    Possible Sources 

    • Fuse
    • Wiring, terminals and connector
    • PSCM

    Visual Inspection and Pre-checks 

    • Verify the high current BJB MEGA fuse 2 (80A) and BJB fuse 65 (5A) are OK.

  2. S1 CHECK THE PSCM (POWER STEERING CONTROL MODULE) VOLTAGE SUPPLY CIRCUITS FOR AN OPEN

    • Ignition OFF.

    • Disconnect: PSCM C1463A and C1463B

    • Ignition ON.

    • Measure:
      Positive Lead Measurement / Action Negative Lead
      C1463A-1
      GFD455923Courtesy of FORD MOTOR COMPANY
      		 Ground

    • Measure:
      Positive Lead Measurement / Action Negative Lead
      C1463B-3
      GFD455923Courtesy of FORD MOTOR COMPANY
      		 Ground

    Is the voltage greater than 11 volts? 

    Yes  GO to  S2
    No  Verify the high current BJB MEGA fuse 2 (80A) and BJB fuse 65 (5A) are OK. If OK, REPAIR the circuit. If not OK, REFER to OEM Electrical Wiring Diagram Introduction to identify the possible causes of the circuit short.

  3. S2 CHECK THE PSCM (POWER STEERING CONTROL MODULE) GROUND CIRCUIT FOR AN OPEN

    • Ignition OFF.

    • Measure:
      Positive Lead Measurement / Action Negative Lead
      C1463A-2
      GFD455922Courtesy of FORD MOTOR COMPANY
      		 Ground

    Is the resistance less than 3 ohms? 

    Yes  GO to  S3
    No  REPAIR the circuit.

  4. S3 CHECK THE HS-CAN2 (HIGH-SPEED CONTROLLER AREA NETWORK 2) CIRCUITS BETWEEN THE PSCM (POWER STEERING CONTROL MODULE) AND THE GWM (GATEWAY MODULE A) FOR AN OPEN

    • Disconnect GWM C2431.

    Are the resistances less than 3 ohms? 

    Yes  CONNECT the GWM, GO to  S4
    No  REPAIR the circuit in question.

  5. S4 CHECK FOR CORRECT PSCM (POWER STEERING CONTROL MODULE) OPERATION

    • Ignition OFF.

    • Disconnect and inspect all the PSCM connectors and related in-line connectors.

    • Repair:

      • corrosion (install new connector or terminals - clean module pins)
      • damaged or bent pins - install new terminals/pins
      • pushed-out pins - install new pins as necessary

    • Reconnect the PSCM connectors and related in-line connectors. Make sure they seat and latch correctly.

    • Operate the system and determine if the concern is still present.

    Is the concern still present? 

    Yes  CHECK OASIS for any applicable service articles: TSB, General Service Bulletin (GSB), SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, REFER to the EPAS Symptom Chart. Refer to EPAS Guided Routine .
    No  The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.
scientia non olet · About LEMON Manuals