Common Specifications & Procedures
TRANSIT COMMON SPECIFICATIONS & PROCEDURES
| System | Specification/Procedure | |||
|---|---|---|---|---|
| Air Conditioning | ||||
| Service | Specifications | |||
| Torque | Refer to appropriate component in Removal And Installation | |||
| Fron Drive Halfshaft Wheel Hub Nut | Stage 1: 74 lb.ft (100 Nm) Stage 2: 184 lb. ft (250 Nm) Stage 3: 380 lb.ft (515 Nm) |
|||
| Axle Nut/Hub Nut | Stage 1: 70 lb.ft (95 Nm) Stage 2: Loosen: 180° Stage 3: 25 lb.ft (34 Nm) |
|||
| Battery | Specifications | |||
| Brakes | ||||
| Bleeding Sequence | Brake System Pressure Bleeding | |||
| Front Disc Brakes w/Torque | Refer to appropriate component in Removal And Installation | |||
| Rear Disc Brakes w/Torque | Refer to appropriate component in Removal And Installation | |||
| Charging | ||||
| Generator w/Torque | ||||
| 3.5L EcoBoost | Generator Mounting Nut: Torque: 35 lb.ft (47 Nm) Generator Mounting Bolt: Torque: 35 lb.ft (47 Nm) Generator Stud: 71 lb.in (8 Nm) |
|||
| 3.5L Duratec | Generator Bolt and Nut: 35 lb.ft (47 Nm) | |||
| Drive Belts | ||||
| Adjustment | ||||
| 3.5L Duratec | Accessory Drive Belt | |||
| 3.5L EcoBoost | Accessory Drive Belt | |||
| Belt Routing | ||||
| 3.5L Duratec | Accessory Drive - Component Location | |||
| 3.5L EcoBoost | Accessory Drive - Component Location | |||
| Engine Cooling | ||||
| General Service Specifications | ||||
| 3.5L Duratec | Specifications | |||
| 3.5L EcoBoost | Specifications | |||
| Radiator Cap Pressure | ||||
| 3.5L Duratec | 120 kPa (17.4 psi) to 150 kPa (21.7 psi) | |||
| 3.5L EcoBoost | 120 kPa (17.4 psi) to 150 kPa (21.7 psi) | |||
| Thermostat R & I | ||||
| 3.5L Duratec | Thermostat . | |||
| 3.5L EcoBoost | Thermostat . | |||
| Water Pump R & I | ||||
| 3.5L Duratec | Coolant Pump | |||
| 3.5L EcoBoost | Coolant Pump | |||
| Engine Mechanical | ||||
| Compression | ||||
| 3.5L EcoBoost | Specifications | |||
| 3.5L Duratec | Specifications | |||
| Oil Pressure | ||||
| 3.5L EcoBoost | Oil pressure @ 1, 500 rpm with engine at normal operating temperature: 30.0 psi (206.8 kPa) | |||
| 3.5L Duratec | Oil pressure @ 1, 500 rpm with engine at normal operating temperature: 21.8 psi (150 kPa) | |||
| Overhaul | ||||
| 3.5L EcoBoost | Specifications | |||
| 3.5L Duratec | Specifications | |||
| Torque | ||||
| 3.5L EcoBoost | Refer to the appropriate component in Removal And Installation | |||
| 3.5L Duratec | Refer to the appropriate component in Removal And Installation | |||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | |||
| Flywheel/Flex Plate Torque | ||||
| 3.5L Ecoboost | Flexplate . | |||
| 3.5L Duratec | Flexplate | |||
| Fuel System | ||||
| Fuel Filter Location | ||||
| 3.5L Ecoboost/3.5L Duratec | Located in fuel tank as part of the fuel pump module. | |||
| Fuel Filter R & I | ||||
| 3.5L EcoBoost | Fuel Pump And Sender Unit | |||
| 3.5L Duratec | Fuel Pump And Sender Unit | |||
| Pressure Release Procedure | ||||
| 3.5L EcoBoost | Fuel System Pressure Release | |||
| 3.5L Duratec | Fuel System Pressure Release | |||
| Fuel pressure | ||||
| 3.5L EcoBoost | Engine running 71.1 psi (490 kPa) |
|||
| 3.5L Duratec | Engine running 75.4 psi (520 kPa) |
|||
| Fuel Pressure Test Procedure | ||||
| 3.5L EcoBoost | Fuel System Pressure Check | |||
| 3.5L Duratec | Fuel System Pressure Check | |||
| Ignition | ||||
| Firing Order & Cylinder Identification | Firing Order & Cylinder Identification | |||
| Ignition Wires (Routing) | Engine has coil-on-plug ignition. | |||
| Spark Plug | ||||
| 3.5L EcoBoost | ||||
| Type | CYFS 12 YT4 | |||
| Gap | 0.028-0.037 in (.7-.95 mm) | |||
| Torque | 133 lb.in (15 Nm) | |||
| 3.5L Duratec | ||||
| Type | CYFS 12F 5 | |||
| Gap | 0.051 in (1.3 mm) | |||
| Torque | 133 lb.in (15 Nm) | |||
| Starting | ||||
| Starter | ||||
| 3.5L EcoBoost | Specifications | |||
| 3.5L Duratec | Specifications | |||
| Torque | ||||
| 3.5L EcoBoost | Starter Motor Mounting Bolts: 26 lb.ft (35 Nm) | |||
| 3.5L Duratec | Starter Motor Mounting Bolts: 26 lb.ft (35 Nm) | |||
| Wheel Alignment | ||||
| Adjustment Specifications | Specifications | |||
| Torque | Refer to General Procedures | |||
| Wheel & Tire | ||||
| Wheel Lug Nut Torque | For tightening sequence, refer to Wheel And Tire
or Wheel And Tire - Vehicles With: Dual Rear Wheels
. 148 lb.ft (200 Nm) |
|||