Diagnostic Trouble Code (DTC) Chart
Diagnostics in this service information assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
Diagnostic Trouble Code Chart
| Module | DTC | Description | Action |
|---|---|---|---|
| IPMA | B120C:11 | Heater for Windshield Mounted Sensor: Circuit Short To Ground | GO to Pinpoint Test C |
| IPMA | B120C:13 | Heater for Windshield Mounted Sensor: Circuit Open | GO to Pinpoint Test C |
| IPMA | B13A6:14 | Lane Departure Warning (LDW) Switch Input: Circuit Short To Ground or Open | GO to Pinpoint Test A |
| IPMA | C0072:00 | Brake Temperature Too High: No Sub Type Information | GO to Pinpoint Test R |
| IPMA | C1001:54 | Vision System Camera: Missing Calibration | GO to Pinpoint Test S |
| IPMA | C1001:78 | Vision System Camera: Alignment or Adjustment Incorrect | GO to Pinpoint Test S |
| IPMA | C1001:97 | Vision System Camera: Component or System Operation Obstructed or Blocked | GO to Pinpoint Test T |
| IPMA | C1001:98 | Vision System Camera: Component or System Over Temperature | GO to Pinpoint Test U |
| IPMA | C1A67:08 | Forward Looking Sensor: Bus Signal/Message Failures | GO to Pinpoint Test V |
| IPMA | U0100:00 | Loss Communication with ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test E |
| IPMA | U0121:00 | Loss Communication With Anti-Lock Brake System Control Module: No Sub Type Information | GO to Pinpoint Test F |
| IPMA | U0130:00 | Lost Communication With Steering Effort Control Module: No Sub Type Information | GO to Pinpoint Test Q |
| IPMA | U0131:00 | Lost Communication With Power Steering Control Module: No Sub-Type Information | GO to Pinpoint Test I |
| IPMA | U0140:00 | Lost Communication With Body Control Module: No Sub-Type Information | GO to Pinpoint Test J |
| IPMA | U0151:00 | Lost Communication With Restraints Control Module: No Sub-Type Information | GO to Pinpoint Test K |
| IPMA | U0155:00 | Lost Communication With Instrument Panel Cluster Control Module: No Sub-Type Information | GO to Pinpoint Test L |
| IPMA | U0212:00 | Lost Communication With Steering Column Control Module: No Sub-Type Information | GO to Pinpoint Test M |
| IPMA | U0232:00 | Lost Communication With Side Obstacle Detection Control Module "A": No Sub Type Information | GO to Pinpoint Test G |
| IPMA | U0233:00 | Lost Communication With Side Obstacle Detection Control Module "B": No Sub Type Information | GO to Pinpoint Test H |
| IPMA | U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test N |
| IPMA | U0401:86 | Invalid Data Received from ECM/PCM A: Signal Invalid | GO to Pinpoint Test W |
| IPMA | U0405:64 | Invalid Data Received From Cruise Control Module: Signal Plausibility Failure | GO to Pinpoint Test X |
| IPMA | U0416:86 | Invalid Data Received From Vehicle Dynamics Control Module: Signal Invalid | GO to Pinpoint Test Y |
| IPMA | U0418:86 | Invalid Data Received from Brake System Control Module "A": Signal Invalid | GO to Pinpoint Test Z |
| IPMA | U0419:86 | Invalid Data Received From Steering Effort Control Module: Signal Invalid | GO to Pinpoint Test AA |
| IPMA | U0420:86 | Invalid Data Received from Power Steering Control Module "A": Signal Invalid | GO to Pinpoint Test AB |
| IPMA | U0422:82 | Invalid Data Received From Body Control Module: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test AC |
| IPMA | U0423:82 | Invalid Date Received From Instrument Panel Cluster Control Module: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test AD |
| IPMA | U0423:86 | Invalid Date Received From Instrument Panel Cluster Control Module: Signal Invalid | GO to Pinpoint Test AD |
| IPMA | U0429:86 | Invalid Data Received From Steering Column Control Module: Signal Invalid | GO to Pinpoint Test AE |
| IPMA | U0452:86 | Invalid Data Received From Restraints Control Module: Signal Invalid | GO to Pinpoint Test AF |
| IPMA | U0533:86 | Invalid Data Received From Side Obstacle Detection Control Module "A": Signal Invalid | GO to Pinpoint Test AG |
| IPMA | U0534:86 | Invalid Data Received From Side Obstacle Detection Control Module "B": Signal Invalid | GO to Pinpoint Test AH |
| IPMA | U1000:11 | Solid State Driver Protection Activated: Circuit Short To Ground | GO to Pinpoint Test AI |
| IPMA | U2018:51 | Control Module Software#3: Not Programmed | GO to Pinpoint Test AJ |
| IPMA | U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test AK |
| IPMA | U2101:64 | Control Module Configuration Incompatible: Signal Plausibility Failure | GO to Pinpoint Test AL |
| IPMA | U2300:55 | Central Configuration: Not Configured | GO to Pinpoint Test AM |
| IPMA | U2300:64 | Central Configuration: Signal Plausibility Failure | GO to Pinpoint Test AN |
| IPMA | U3000:41 | Control Module: General Check Sum Failure | GO to Pinpoint Test AO |
| IPMA | U3000:42 | Control Module: General Memory Failure | GO to Pinpoint Test AP |
| IPMA | U3000:44 | Control Module: Data Memory Failure | GO to Pinpoint Test AQ |
| IPMA | U3000:49 | Control Module: Internal Electronic Failure | GO to Pinpoint Test AQ |
| IPMA | U3000:64 | Control Module: Signal Plausibility Failure | GO to Pinpoint Test AR |
| IPMA | U3003:16 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test O |
| IPMA | U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test P |