Pinpoint Test F: U023A:87
- Refer to Module Communications Network
for schematic and connector information.
Normal Operation and Fault Conditions
DTC Fault Trigger Conditions
DTC Description Fault Trigger Condition BCMC U023A:87 Lost Communication With Image Processing Module A: Missing Message A continuous memory DTC that sets in the BCMC if data messages received from the IPMA module through the GWM are missing. Possible Sources
- Communication network concern
- IPMA
- BCMC (BJB)
- F1 CHECK THE COMMUNICATION NETWORK
- Ignition ON.
- Using a diagnostic scan tool, perform a network test.
Does the IPMA pass the network test?
Yes GO to F2 No REFER to: Controller Area Network (CAN) Module Communications Network - F2 CHECK THE BCMC (BODY CONTROL MODULE C) CONTINUOUS MEMORY DIAGNOSTIC TROUBLE CODES (CMDTCS)
- Using a diagnostic scan tool, clear the Diagnostic Trouble Codes (DTCs).
- Wait 10 seconds.
- Using a diagnostic scan tool, check the BCMC Continuous Memory Diagnostic Trouble Codes (CM DTCs).
Is BCMC DTC U023A:87 retrieved again?
Yes GO to F3 No The system is operating correctly at this time. The DTC may have been set due to high network traffic or an intermittent fault condition. - F3 RETRIEVE THE IPMA (IMAGE PROCESSING MODULE A) DIAGNOSTIC TROUBLE CODES (DTCS)
- Using a diagnostic scan tool, perform the IPMA self-test.
Are any IPMA Diagnostic Trouble Codes (DTCs) recorded?
Yes REFER to: Lane Keeping System No GO to F4 - F4 RECHECK THE BCMC (BODY CONTROL MODULE C) CONTINUOUS MEMORY DIAGNOSTIC TROUBLE CODES (CMDTCS)
- Using a diagnostic scan tool, clear the Diagnostic Trouble Codes (DTCs).
- Wait 10 seconds.
- Using a diagnostic scan tool, check the BCMC Continuous Memory Diagnostic Trouble Codes (CM DTCs).
Is DTC U023A:87 still present?
Yes GO to F5 No The system is operating correctly at this time. The DTC may have been set due to high network traffic or an intermittent fault condition. - F5 CHECK FOR DTC (DIAGNOSTIC TROUBLE CODE) U023A:87 SET IN OTHER MODULES
- Using a diagnostic scan tool, clear the Diagnostic Trouble Codes (DTCs).
- Ignition OFF.
- Ignition ON.
- Wait 10 seconds.
- Using a diagnostic scan tool, retrieve all
Continuous Memory Diagnostic Trouble Codes (CM DTCs).
Is DTC U023A:87 set in other modules?
Yes GO to F6 No GO to F7 - F6 CHECK FOR CORRECT IPMA (IMAGE PROCESSING MODULE A) OPERATION
- Disconnect and inspect the IPMA connector.
- Repair:
- corrosion (install new connector or terminals - clean module pins)
- damaged or bent pins - install new terminals/pins
- pushed-out pins - install new pins as necessary
- Reconnect the IPMA connector. Make sure it seats and latches correctly.
- Operate the system and determine if the concern is still present.
Is the concern still present?
Yes CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, INSTALL a new IPMA. REFER to: Image Processing Module A (IPMA) No The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues. - F7 CHECK FOR CORRECT BCMC (BODY CONTROL MODULE C) OPERATION
- Disconnect and inspect all BCMC connectors.
- Repair:
- corrosion (install new connector or terminals - clean module pins)
- damaged or bent pins - install new terminals/pins
- pushed-out pins - install new pins as necessary
- Connect the BCMC connectors. Make sure they seat and latch correctly.
- Operate the system and determine if the concern is still present.
Is the concern still present?
Yes CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, INSTALL a new BCMC. REFER to: Body Control Module C (BCMC) No The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.