| C0051:23 |
Steering Wheel Position Sensor: Signal Stuck Low |
GO to Pinpoint Test AG |
| C0051:27 |
Steering Wheel Position Sensor: Signal Rate Of Change Above Threshold |
GO to Pinpoint Test AG |
| C0051:28 |
Steering Wheel Position Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure |
GO to Pinpoint Test AG |
| C0051:41 |
Steering Wheel Position Sensor: General Checksum Failure |
GO to Pinpoint Test AG |
| C0051:54 |
Steering Wheel Position Sensor: Missing Calibration |
GO to Pinpoint Test AG |
| C0051:62 |
Steering Wheel Position Sensor: Signal Compare Failure |
GO to Pinpoint Test AG |
| C0051:64 |
Steering Wheel Position Sensor: Signal Plausibility Failure |
GO to Pinpoint Test AG |
| C0051:67 |
Steering Wheel Position Sensor: Signal Incorrect After Event |
GO to Pinpoint Test AG |
| C0051:85 |
Steering Wheel Position Sensor: Signal Above Allowable Range |
GO to Pinpoint Test AG |
| C0051:86 |
Steering Wheel Position Sensor: Signal Invalid |
GO to Pinpoint Test AG |
| C006B:00 |
Stability System Active Too Long: No Sub Type Information |
GO to Pinpoint Test AG |
| B1D23:4B |
Overheat Sensor: Over Temperature |
GO to Pinpoint Test BB |
| C102D:00 |
High Friction Inside Power Steering: No Sub Type Information |
GO to Pinpoint Test J |
| C1110:56 |
Power steering Calibration Data: Invalid/Incompatible Configuration |
GO to Pinpoint Test E |
| C1B00:49 |
Steering Angle Sensor: Internal Electronic Failure |
GO to Pinpoint Test X |
| C1B00:62 |
Steering Angle Sensor: Signal Compare Failure |
GO to Pinpoint Test W |
| C200B:49 |
Steering Shaft Torque Sensor 1: Internal Electronic Failure |
GO to Pinpoint Test O |
| C200B:62 |
Steering Shaft Torque Sensor 1: Signal Compare Failure |
GO to Pinpoint Test R |
| C200C:49 |
Steering Shaft Torque Sensor 2: Internal Electronic Failure |
GO to Pinpoint Test P |
| C200C:62 |
Steering Shaft Torque Sensor 2: Signal Compare Failure |
GO to Pinpoint Test S |
| C200D:49 |
Motor Rotation Angle Sensor: Internal Electronic Failure |
GO to Pinpoint Test Q |
| C200D:62 |
Motor Rotation Angle Sensor: Signal Compare Failure |
GO to Pinpoint Test T |
| U0100:00 |
Lost Communication With ECM / PCM "A": No Sub Type Information |
GO to Pinpoint Test AB |
| U0102:00 |
Lost Communication with Transfer Case Control Module: No Sub Type Information |
GO to Pinpoint Test CF |
| U0121:00 |
Lost Communication With Anti-lock Brake System (ABS) Control Module: No Sub Type Information |
GO to Pinpoint Test AI |
| U0126:00 |
Lost Communication with Steering Angle Sensor Module: No Sub Type Information |
GO to Pinpoint Test AY |
| U0137:00 |
Lost Communication with Trailer Brake Control Module: No Sub Type Information |
GO to Pinpoint Test CK |
| U0140:00 |
Lost Communication with Body Control Module: No Sub Type Information |
GO to Pinpoint Test AL |
| U0146:00 |
Lost Communication With Serial Data Gateway "A": No Sub Type Information |
GO to Pinpoint Test AM |
| U0151:00 |
Lost Communication With Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test AN |
| U0155:00 |
Lost Communication with Instrument Panel Cluster (IPC) Control Module: No Sub Type Information |
GO to Pinpoint Test AO |
| U0159:00 |
Lost Communication with Parking Assist Control Module "A": No Sub Type Information |
GO to Pinpoint Test AP |
| U0212:00 |
Lost Communication with Steering Column Control Module: No Sub Type Information |
GO to Pinpoint Test AQ |
| U023A:00 |
Lost Communication With Image Processing Module A: No Sub Type Information |
GO to Pinpoint Test AR |
| U0253:00 |
Lost Communication with Accessory Protocol Interface Module: No Sub Type Information |
GO to Pinpoint Test BT |
| U0256:00 |
Lost Communication with Front Controls Interface Module: No Sub Type Information |
GO to Pinpoint Test CL |
| U0401:00 |
Invalid Data Received from Powertrain Control Module: No Sub Type Information |
GO to Pinpoint Test U |
| U0403:00 |
Invalid Data Received from Transfer Case Control Module: No Sub Type Information |
GO to Pinpoint Test CJ |
| U0415:00 |
Invalid Data Received from Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information |
GO to Pinpoint Test V |
| U0415:22 |
Invalid Data Received from Anti-Lock Brake System (ABS) Control Module "A": Signal Amplitude Greater Than Maximum |
GO to Pinpoint Test V |
| U0422:00 |
Invalid Data Received From Body Control Module: No Sub Type Information |
GO to Pinpoint Test BU |
| U0423:00 |
Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information |
GO to Pinpoint Test BW |
| U0428:00 |
Invalid Data Received from the Steering Angle Sensor Module: No Sub Type Information |
GO to Pinpoint Test BV |
| U0452:00 |
Invalid Data Received From Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test BX |
| U045A:00 |
Invalid Data Received from the Parking Assist Control Module: No Sub Type Information |
GO to Pinpoint Test AW |
| U053B:00 |
Invalid Data Received From Image Processing Module A: No Sub Type Information |
GO to Pinpoint Test AX |
| U0554:00 |
Invalid Data Received From The Accessory Protocol Interface Module: No Sub Type Information |
GO to Pinpoint Test CD |
| U0557:00 |
Invalid Data Received From Front Controls Interface Module "A": No Sub Type Information |
GO to Pinpoint Test CM |
| U2014:78 |
Control Module Hardware: Alignment Or Adjustment Incorrect |
GO to Pinpoint Test H |
| U2014:81 |
Control Module Hardware: Invalid Serial Data Received |
GO to Pinpoint Test H |
| U2014:92 |
Control Module Hardware: Performance Or Incorrect Operation |
GO to Pinpoint Test H |
| U2016:47 |
Control Module Main Software: Watchdog/Safety μC Failure |
GO to Pinpoint Test Y |
| U2016:48 |
Control Module Main Software: Supervision Software Failure |
GO to Pinpoint Test Y |
| U202B:00 |
In-Use Application Signing Key: No Sub Type Information |
GO to Pinpoint Test CR |
| U202B:56 |
In-Use Application Signing Key: Invalid/Incompatible Configuration |
GO to Pinpoint Test CR |
| U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test AA |
| U2300:55 |
Central Configuration: Not Configured |
GO to Pinpoint Test F |
| U2300:56 |
Central Configuration: Invalid/Incompatible Configuration |
GO to Pinpoint Test F |
| U3000:42 |
Control Module: General Memory Failure |
GO to Pinpoint Test C |
| U3000:49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test C |
| U3000:61 |
Control Module: Signal Calculation Failure |
GO to Pinpoint Test C |
| U3000:96 |
Control Module: Component Internal Failure |
GO to Pinpoint Test B |
| U3001:68 |
Control Module Improper Shutdown Performance: Event Information |
GO to Pinpoint Test BD |
| U3001:89 |
Control Module Improper Shutdown Performance: Data Transfer Failure |
GO to Pinpoint Test BD |
| U3003:16 |
Battery Voltage: Circuit Voltage Below Threshold |
GO to Pinpoint Test Z |
| U3003:17 |
Battery Voltage: Circuit Voltage Above Threshold |
GO to Pinpoint Test Z |
| U3003:18 |
Battery Voltage: Circuit Current Below Threshold |
GO to Pinpoint Test Z |
| U3003:19 |
Battery Voltage: Circuit Current Above Threshold |
GO to Pinpoint Test Z |
| U3003:68 |
Battery Voltage: Event Information |
GO to Pinpoint Test Z |
| U3003:A2 |
Battery Voltage: System Voltage Low |
GO to Pinpoint Test Z |
| U3008:1B |
Control Module Ground "A": Circuit Resistance Above Threshold |
GO to Pinpoint Test CS |
| U3009:1B |
Control Module Ground "B": Circuit Resistance Above Threshold |
GO to Pinpoint Test CT |