| B1026:04 |
Steering Column Lock: System Internal Failure |
DIAGNOSE all other Diagnostic Trouble Codes (DTCs) present. If no other Diagnostic Trouble Codes (DTCs) are present, INSTALL a new steering column lock module. REFER to: Steering Column Lock Module |
| B1026:05 |
Steering Column Lock: System Programming Failure |
CARRY OUT the BCM to Electronic Steering Column Lock (ESCL) configuration/training procedure. REFER to: ANTI-THEFT KEY PROGRAMMING - SCAN TOOL
. |
| B1026:09 |
Steering Column Lock: Component Failure |
CARRY OUT a battery disconnect and reconnect procedure and RETEST Electronic Steering Column Lock (ESCL) operation. REFER to: Battery Disconnect and Connect
.
. If no change, INSTALL a new steering column lock module. REFER to: Steering Column Lock Module |
| B1026:49 |
Steering Column Lock: Internal Electronic Failure |
CARRY OUT a battery disconnect and reconnect procedure and RETEST Electronic Steering Column Lock (ESCL) operation. REFER to: Battery Disconnect and Connect
.
. If no change, INSTALL a new steering column lock module. REFER to: Steering Column Lock Module |
| B1026:51 |
Steering Column Lock: Not Programmed |
CARRY OUT the BCM to Electronic Steering Column Lock (ESCL) configuration/training procedure. REFER to:ANTI-THEFT KEY PROGRAMMING - SCAN TOOL
. |
| B1026:56 |
Steering Column Lock: Invalid /Incompatible Configuration |
CARRY OUT the BCM to Electronic Steering Column Lock (ESCL) configuration/training procedure. REFER to:ANTI-THEFT KEY PROGRAMMING - SCAN TOOL
. |
| B1026:62 |
Steering Column Lock: Signal Compare Failure |
CARRY OUT the BCM to Electronic Steering Column Lock (ESCL) configuration/training procedure. REFER to:ANTI-THEFT KEY PROGRAMMING - SCAN TOOL
. |
| B1026:77 |
Steering Column Lock: Commanded Position Not Reachable |
INSTALL a new steering column lock module. REFER to: Steering Column Lock Module |
| B1026:87 |
Steering Column Lock: Missing Message |
GO to Pinpoint Test D |
| B1026:92 |
Steering Column Lock: Performance or Incorrect Operation |
GO to Pinpoint Test D |
| B1026:93 |
Steering Column Lock: No Operation |
DIAGNOSE all other Diagnostic Trouble Codes (DTCs) present. If no other Diagnostic Trouble Codes (DTCs) are present, INSTALL a new steering column lock module. |
| B1026:96 |
Steering Column Lock: Component Internal Failure |
INSTALL a new steering column lock module. |
| B108A:01 |
Start Button: General Electrical Failure |
GO to Pinpoint Test A |
| B108A:9E |
Start Button: Stuck On |
GO to Pinpoint Test A |
| B108A:24 |
Start Button: Signal Stuck High |
GO to Pinpoint Test A |
| B1142:29 |
Ignition Status 1: Signal Invalid |
GO to Pinpoint Test A |
| B1184:11 |
Steering Column Lock Output: Circuit Short To Ground |
GO to Pinpoint Test D |
| B1184:12 |
Steering Column Lock Output: Circuit Short To Battery |
GO to Pinpoint Test D |
| B1184:15 |
Steering Column Lock Output: Circuit Short To Battery or Open |
GO to Pinpoint Test D |
| B1240:11 |
Start Button Mode Indicator: Circuit Short to Ground |
GO to Pinpoint Test B |
| B1240:15 |
Start Button Mode Indicator: Circuit Short to Battery or Open |
If the ignition mode indicator is inoperative, GO to Pinpoint Test B
If the ignition mode indicator is always on, GO to Pinpoint Test C |
| B130F:12 |
Run Accessory Control: Circuit Short to Battery |
REFER to: Wipers and Washers |
| B130F:14 |
Run Accessory Control: Circuit Short to Ground or Open |
REFER to: Wipers and Washers |
| All other Diagnostic Trouble Codes (DTCs) |
- |
REFER to: Body Control Module (BCM) |