Pinpoint Test C: AWD Module Power, Ground, Or Internal Fault
WARNING: This page is about a different variant/trim than selected.
- Refer to FOUR WHEEL DRIVE SYSTEMS
for schematic and connector information.
Normal Operation and Fault Conditions
If the AWD module observes an overpower or a low voltage condition, a DTC is set.
DTC Fault Trigger Conditions
DTC Description Fault Trigger Condition AWD C00A1:57 Driveline Control Module: Invalid/Incompatible Software Component Sets when the AWD module detects invalid / incompatible software. AWD C00A1:F1 Driveline Control Module: Ethernet 2 Failure Indicates the AWD module went into a safe state. AWD P0562:00 System Voltage Low: No Sub Type Information The AWD module detected battery voltage below 9 volts on the voltage supply input circuit. AWD P0563:00 System Voltage High: No Sub Type Information The AWD module detected battery voltage above 16 volts on the voltage supply input circuit. AWD P0603:00 Internal Control Module Keep Alive Memory (KAM) Error: No Sub Type Information The AWD module detected an internal fault which may have been caused by a voltage supply concern to the module. AWD P0604:00 Internal Control Module Random Access Memory (RAM) Error: No Sub Type Information The AWD module detected an internal fault which may have been caused by a voltage supply concern to the module. AWD P0605:00 Internal Control Module Read Only Memory (ROM) Error: No Sub Type Information The AWD module detected an internal fault which may have been caused by a voltage supply concern to the module. AWD P0607:00 Control Module Performance: No Sub Type Information The AWD module detected an internal fault which may have been caused by a voltage supply concern to the module. AWD P060A:00 Internal Control Module Monitoring Processor Performance: No Sub Type Information The AWD module detected an internal fault which may have been caused by a voltage supply concern to the module. AWD P060B:00 Internal Control Module A/D Processing Performance: No Sub Type Information The AWD module detected an internal fault which may have been caused by a voltage supply concern to the module. AWD P060C:00 Internal Control Module Main Processor Performance: No Sub Type Information The AWD module detected an internal fault which may have been caused by a voltage supply concern to the module. AWD P064F:00 Unauthorized Software/Calibration Detected: No Sub Type Information Sets when the AWD module detects unauthorized software/calibration detected. AWD P068A:00 ECM/PCM Power Relay De-Energized - Too Early: No Sub Type Information The AWD module detected 0 volts on the voltage supply input circuit before it was expected. AWD P166E:00 Internal Control Module All Wheel Drive Disconnect Control Performance: No Sub Type Information This DTC sets when a malfunction has been detected by the AWD module. AWD P1674:00 Control Module Software Corrupted: No Sub Type Information Sets when the AWD module detects control module software corrupted. Possible Sources
- Vehicle level voltage concern
- AWD module voltage supply
- AWD module ground
- AWD module
- Wrong AWD software flashed on module -Overall vehicle battery supply
- C1 CHECK FOR VOLTAGE DTC IN OTHER MODULES
- Ignition ON.
- Connect the diagnostic scan tool.
- Retrieve continuous memory DTC.
Are voltage DTC set in other modules?
Yes REFER to: Charging System - 2.3L EcoBoost (199kW/270PS) . REFER to: Charging System - 2.7L EcoBoost (238kW/324PS) . No GO to C2 - C2 CHECK VOLTAGE AND GROUND TO THE AWD MODULE
- Ignition OFF.
- Disconnect AWD module connector C2371.
- Ignition ON.
Is the voltage between 11 and 14 volts?
Yes GO to C4 No GO to C3 - C3 CHECK VOLTAGE TO THE AWD MODULE
Is the voltage greater than 10v and remain constant while wiggle testing the harness?
Yes REPAIR the ground circuit. CLEAR all CMDTC. No VERIFY BJB fuse 15 (25A) and fuse 54 (40A) is OK. If OK, REPAIR the open circuit or short to power. If not OK, REFER to OEM Electrical Wiring Diagram Introduction to identify possible causes of the circuit short. CLEAR all CMDTC. - C4 VERIFY CONCERN IS PRESENT
- Ignition ON.
- Connect the diagnostic scan tool.
- Clear continuous memory DTC.
- Ignition OFF.
- Open and Close Driver's door to initiate module shut down.
- Wait 1 minute for AWD module to sleep.
- Start Engine, allow to idle for 1 minute.
- Retrieve continuous memory DTC.
Did the voltage or internal fault DTC set again?
Yes INSTALL a new AWD module. REFER to: All-Wheel Drive (AWD) Module . No The system is operating correctly at this time. The concern may have been caused by module connections. Address the root cause of any connector or pin issues.