Supplemental Restraint System DTCS
NOTE:
Unlisted Diagnostic Trouble Codes (DTCs) are often retrieved as a result of incorrect repair procedures. Before attempting any repairs for unlisted Diagnostic Trouble Codes (DTCs), check the vehicle service history for recent repairs. For RCM Diagnostic Trouble Codes (DTCs) not listed in this chart,
- Repair all other RCM Diagnostic Trouble Codes (DTCs) before attempting to repair any Diagnostic Trouble Codes (DTCs) not listed in this chart.
- If no other RCM Diagnostic Trouble Codes (DTCs) are retrieved, CLEAR the RCM Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If the RCM Diagnostic Trouble Codes (DTCs) return, VERIFY that the RCM is the correct part number for the vehicle application, and INSTALL As-Built data following scan tool instructions under Module Programming > As-Built.
- Inspect the RCM and RCM connectors for any damaged pins or connections.
Diagnostic Trouble Code Chart
| DTC | Description | Action |
|---|---|---|
| B00A0:11 | Occupant Classification System: Circuit Short to Ground | GO to Pinpoint Test BD |
| B00A0:12 | Occupant Classification System: Circuit Short to Battery | GO to Pinpoint Test BD |
| B1123:11 | Restraints Ignition Relay: Circuit Short to Ground | GO to Pinpoint Test BD |
| B1123:12 | Restraints Ignition Relay: Circuit Short to Battery | GO to Pinpoint Test BD |
| B11D8:01 | Restraint Event Notification: General Electrical Failure | GO to Pinpoint Test T |
| B0061:11 | Passenger Seatbelt Tension Sensor: Circuit Short to Ground | GO to Pinpoint Test BA |
| B0061:12 | Passenger Seatbelt Tension Sensor: Circuit Short to Battery | GO to Pinpoint Test BA |
| B0061:13 | Passenger Seatbelt Tension Sensor: Circuit Open | GO to Pinpoint Test BA |
| B0061:64 | Passenger Seatbelt Tension Sensor: Signal Plausibility Failure | GO to Pinpoint Test BA |
| B00C0:11 | Passenger Seat Occupant Classification Sensor "A": Circuit Short To Ground | GO to Pinpoint Test BC |
| B00C0:12 | Passenger Seat Occupant Classification Sensor "A": Circuit Short To Battery | GO to Pinpoint Test BC |
| B00C0:16 | Passenger Seat Occupant Classification Sensor "A": Circuit Voltage Below Threshold | GO to Pinpoint Test BC |
| B00C0:49 | Passenger Seat Occupant Classification Sensor "A": Internal Electronic Failure | GO to Pinpoint Test BC |
| B00C0:7B | Passenger Seat Occupant Classification Sensor "A": Low Fluid Level | GO to Pinpoint Test BC |
| B00C2:11 | Passenger Seat Occupant Classification Sensor "C": Circuit Short to Ground | GO to Pinpoint Test BB |
| B00C2:12 | Passenger Seat Occupant Classification Sensor "C": Circuit Short to Battery | GO to Pinpoint Test BB |
| B1193:00 | Crash Event Storage Full and Locked: No Sub Type Information | GO to Pinpoint Test BE |
| U0100:00 | Lost Communication with ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test BF |
| U0151:00 | Lost Communication with Restraints Control Module: No Sub Type Information | GO to Pinpoint Test BG |
| U0401:00 | Invalid Data Received from ECM/PCM A: No Sub Type Information | GO to Pinpoint Test BH |
| U3000:41 | Control Module: General Checksum Failure | GO to Pinpoint Test BI |
| U3000:42 | Control Module: General Memory Failure | GO to Pinpoint Test BI |
| U3000:46 | Control Module: Special Memory Failure | GO to Pinpoint Test BI |
| U3000:54 | Control Module: Missing Calibration | GO to Pinpoint Test BJ |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AZ |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AZ |
| B0001:11 | Driver Frontal Stage 1 Deployment Control: Circuit Short to Ground | GO to Pinpoint Test A |
| B0001:12 | Driver Frontal Stage 1 Deployment Control: Circuit Short to Battery | GO to Pinpoint Test A |
| B0001:13 | Driver Frontal Stage 1 Deployment Control: Circuit Open | GO to Pinpoint Test A |
| B0001:1A | Driver Frontal Stage 1 Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test A |
| B0001:2B | Driver Frontal Stage 1 Deployment Control: Signal Cross Coupled | GO to Pinpoint Test AL |
| B0001:4A | Driver Frontal Stage 1 Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AM |
| B0002:11 | Driver Frontal Stage 2 Deployment Control: Circuit Short to Ground | GO to Pinpoint Test B |
| B0002:12 | Driver Frontal Stage 2 Deployment Control: Circuit Short to Battery | GO to Pinpoint Test B |
| B0002:13 | Driver Frontal Stage 2 Deployment Control: Circuit Open | GO to Pinpoint Test B |
| B0002:1A | Driver Frontal Stage 2 Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test B |
| B0002:2B | Driver Frontal Stage 2 Deployment Control: Signal Cross Coupled | GO to Pinpoint Test AL |
| B0002:4A | Driver Frontal Stage 2 Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AM |
| B0010:11 | Passenger Frontal Stage 1 Deployment Control: Circuit Short to Ground | GO to Pinpoint Test C |
| B0010:12 | Passenger Frontal Stage 1 Deployment Control: Circuit Short to Battery | GO to Pinpoint Test C |
| B0010:13 | Passenger Frontal Stage 1 Deployment Control: Circuit Open | GO to Pinpoint Test C |
| B0010:1A | Passenger Frontal Stage 1 Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test C |
| B0010:2B | Passenger Frontal Stage 1 Deployment Control: Signal Cross Coupled | GO to Pinpoint Test AL |
| B0010:4A | Passenger Frontal Stage 1 Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AM |
| B0011:11 | Passenger Frontal Stage 2 Deployment Control: Circuit Short to Ground | GO to Pinpoint Test D |
| B0011:12 | Passenger Frontal Stage 2 Deployment Control: Circuit Short to Battery | GO to Pinpoint Test D |
| B0011:13 | Passenger Frontal Stage 2 Deployment Control: Circuit Open | GO to Pinpoint Test D |
| B0011:1A | Passenger Frontal Stage 2 Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test D |
| B0011:2B | Passenger Frontal Stage 2 Deployment Control: Signal Cross-Coupled | GO to Pinpoint Test AL |
| B0011:4A | Passenger Frontal Stage 2 Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AM |
| B0050:11 | Driver Seatbelt Sensor: Circuit Short to Ground | GO to Pinpoint Test E |
| B0050:12 | Driver Seatbelt Sensor: Circuit Short to Battery | GO to Pinpoint Test E |
| B0050:13 | Driver Seatbelt Sensor: Circuit Open | GO to Pinpoint Test E |
| B0050:1D | Driver Seatbelt Sensor: Circuit Current Out of Range | GO to Pinpoint Test E |
| B0050:2B | Driver Seatbelt Sensor: Signal Cross-Coupled | GO to Pinpoint Test AL |
| B0050:4A | Driver Seatbelt Sensor: Incorrect Component Installed | GO to Pinpoint Test AM |
| B0052:11 | Passenger Seatbelt Sensor: Circuit Short to Ground | GO to Pinpoint Test F |
| B0052:12 | Passenger Seatbelt Sensor: Circuit Short to Battery | GO to Pinpoint Test F |
| B0052:13 | Passenger Seatbelt Sensor: Circuit Open | GO to Pinpoint Test F |
| B0052:1D | Passenger Seatbelt Sensor: Circuit Current Out of Range | GO to Pinpoint Test F |
| B0052:2B | Passenger Seatbelt Sensor: Signal Cross-Coupled | GO to Pinpoint Test AL |
| B0052:4A | Passenger Seatbelt Sensor: Incorrect Component Installed | GO to Pinpoint Test AM |
| B0054:11 | Second Row Center Seatbelt Sensor: Circuit Short To Ground | GO to Pinpoint Test G |
| B0054:12 | Second Row Center Seatbelt Sensor: Circuit Short To Battery | GO to Pinpoint Test G |
| B0054:13 | Second Row Center Seatbelt Sensor: Circuit Open | GO to Pinpoint Test G |
| B0054:1D | Second Row Center Seatbelt Sensor: Circuit Current Out Of Range | GO to Pinpoint Test G |
| B0054:2B | Second Row Center Seatbelt Sensor: Signal Cross-Coupled | GO to Pinpoint Test AL |
| B0054:4A | Second Row Center Seatbelt Sensor: Incorrect Component Installed | GO to Pinpoint Test AM |
| B0070:11 | Driver Seatbelt Pretensioner "A" Deployment Control: Circuit Short to Ground | GO to Pinpoint Test H |
| B0070:12 | Driver Seatbelt Pretensioner "A" Deployment Control: Circuit Short to Battery | GO to Pinpoint Test H |
| B0070:13 | Driver Seatbelt Pretensioner "A" Deployment Control: Circuit Open | GO to Pinpoint Test H |
| B0070:1A | Driver Seatbelt Pretensioner "A" Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test H |
| B0070:2B | Driver Seatbelt Pretensioner "A" Deployment Control: Signal Cross Coupled | GO to Pinpoint Test AL |
| B0070:4A | Driver Seatbelt Pretensioner "A" Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AM |
| B0072:11 | Passenger Seatbelt Pretensioner "A" Deployment Control: Circuit Short to Ground | GO to Pinpoint Test I |
| B0072:12 | Passenger Seatbelt Pretensioner "A" Deployment Control: Circuit Short to Battery | GO to Pinpoint Test I |
| B0072:13 | Passenger Seatbelt Pretensioner "A" Deployment Control: Circuit Open | GO to Pinpoint Test I |
| B0072:1A | Passenger Seatbelt Pretensioner "A" Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test I |
| B0072:2B | Passenger Seatbelt Pretensioner "A" Deployment Control: Signal Cross Coupled | GO to Pinpoint Test AL |
| B0072:4A | Passenger Seatbelt Pretensioner "A" Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AM |
| B007E:11 | Driver Seatbelt Pretensioner "C" Deployment Control: Circuit Short to Ground | GO to Pinpoint Test J |
| B007E:12 | Driver Seatbelt Pretensioner "C" Deployment Control: Circuit Short to Battery | GO to Pinpoint Test J |
| B007E:13 | Driver Seatbelt Pretensioner "C" Deployment Control: Circuit Open | GO to Pinpoint Test J |
| B007E:1A | Driver Seatbelt Pretensioner "C" Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test J |
| B007E:2B | Driver Seatbelt Pretensioner "C" Deployment Control: Signal Cross-Coupled | GO to Pinpoint Test AL |
| B007E:4A | Driver Seatbelt Pretensioner "C" Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AM |
| B007F:11 | Passenger Seatbelt Pretensioner "C" Deployment Control: Circuit Short to Ground | GO to Pinpoint Test K |
| B007F:12 | Passenger Seatbelt Pretensioner "C" Deployment Control: Circuit Short to Battery | GO to Pinpoint Test K |
| B007F:13 | Passenger Seatbelt Pretensioner "C" Deployment Control: Circuit Open | GO to Pinpoint Test K |
| B007F:1A | Passenger Seatbelt Pretensioner "C" Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test K |
| B007F:2B | Passenger Seatbelt Pretensioner "C" Deployment Control: Signal Cross-Coupled | GO to Pinpoint Test AL |
| B007F:4A | Passenger Seatbelt Pretensioner "C" Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AM |
| B0082:11 | Passenger Seatbelt Load Limiter Deployment Control: Circuit Short to Ground | GO to Pinpoint Test L |
| B0082:12 | Passenger Seatbelt Load Limiter Deployment Control: Circuit Short to Battery | GO to Pinpoint Test L |
| B0082:13 | Passenger Seatbelt Load Limiter Deployment Control: Circuit Open | GO to Pinpoint Test L |
| B0082:1A | Passenger Seatbelt Load Limiter Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test L |
| B0082:2B | Passenger Seatbelt Load Limiter Deployment Control: Signal Cross Coupled | GO to Pinpoint Test AL |
| B0082:4A | Passenger Seatbelt Load Limiter Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AM |
| B00A0:09 | Occupant Classification System: Component Failure | GO to Pinpoint Test M |
| B00A0:4A | Occupant Classification System: Incorrect Component Installed | GO to Pinpoint Test AM |
| B00A0:63 | Occupant Classification System: Circuit / Component Protection Time-Out | GO to Pinpoint Test M |
| B00A0:64 | Occupant Classification System: Signal Plausibility Failure | GO to Pinpoint Test M |
| B00A0:68 | Occupant Classification System: Event Information | GO to Pinpoint Test M |
| B00B5:11 | Driver Seat Track Position Restraints Sensor: Circuit Short to Ground | GO to Pinpoint Test N |
| B00B5:12 | Driver Seat Track Position Restraints Sensor: Circuit Short to Battery | GO to Pinpoint Test N |
| B00B5:13 | Driver Seat Track Position Restraints Sensor: Circuit Open | GO to Pinpoint Test N |
| B00B5:1D | Driver Seat Track Position Restraints Sensor: Circuit Current Out of Range | GO to Pinpoint Test N |
| B00B5:2B | Driver Seat Track Position Restraints Sensor: Signal Cross Coupled | GO to Pinpoint Test AL |
| B00B5:4A | Driver Seat Track Position Restraints Sensor: Incorrect Component Installed | GO to Pinpoint Test AM |
| B00C5:11 | Passenger Seat Track Position Restraints Sensor: Circuit Short to Ground | GO to Pinpoint Test O |
| B00C5:12 | Passenger Seat Track Position Restraints Sensor: Circuit Short to Battery | GO to Pinpoint Test O |
| B00C5:13 | Passenger Seat Track Position Restraints Sensor: Circuit Open | GO to Pinpoint Test O |
| B00C5:1D | Passenger Seat Track Position Restraints Sensor: Circuit Current Out of Range | GO to Pinpoint Test O |
| B00C5:2B | Passenger Seat Track Position Restraints Sensor: Signal Cross Coupled | GO to Pinpoint Test AL |
| B00C5:4A | Passenger Seat Track Position Restraints Sensor: Incorrect Component Installed | GO to Pinpoint Test AM |
| B00D5:11 | Restraint System Passenger Disable Indicator: Circuit Short To Ground | GO to Pinpoint Test P |
| B00D5:12 | Restraint System Passenger Disable Indicator: Circuit Short To Battery | GO to Pinpoint Test P |
| B00D5:13 | Restraint System Passenger Disable Indicator: Circuit Open | GO to Pinpoint Test P |
| B00D5:4A | Restraint System Passenger Disable Indicator: Incorrect Component Installed | GO to Pinpoint Test AM |
| B1193:00 | Crash Event Storage Full and Locked: No Sub Type Information | GO to Pinpoint Test R |
| B11CF:11 | Passenger Frontal Airbag Canister Vent: Circuit Short to Ground | GO to Pinpoint Test S |
| B11CF:12 | Passenger Frontal Airbag Canister Vent: Circuit Short to Battery | GO to Pinpoint Test S |
| B11CF:13 | Passenger Frontal Airbag Canister Vent: Circuit Open | GO to Pinpoint Test S |
| B11CF:1A | Passenger Frontal Airbag Canister Vent: Circuit Resistance Below Threshold | GO to Pinpoint Test S |
| B11CF:2B | Passenger Frontal Airbag Canister Vent: Signal Cross Coupled | GO to Pinpoint Test AL |
| B11CF:4A | Passenger Frontal Airbag Canister Vent: Incorrect Component Installed | GO to Pinpoint Test AM |
| B11D8:11 | Restraint Event Notification: Circuit Short To Ground | GO to Pinpoint Test T |
| B11D8:12 | Restraint Event Notification: Circuit Short To Battery | GO to Pinpoint Test T |
| B11D8:13 | Restraint Event Notification: Circuit Open | GO to Pinpoint Test T |
| B1202:11 | Restraint System Passenger Enable Indicator: Circuit Short To Ground | GO to Pinpoint Test Q |
| B1202:12 | Restraint System Passenger Enable Indicator: Circuit Short To Battery | GO to Pinpoint Test Q |
| B1202:13 | Restraint System Passenger Enable Indicator: Circuit Open | GO to Pinpoint Test Q |
| B1202:4A | Restraint System Passenger Enable Indicator: Incorrect Component Installed | GO to Pinpoint Test AM |
| B1404:11 | Driver Side Airbag Deployment Control: Circuit Short to Ground | GO to Pinpoint Test U |
| B1404:12 | Driver Side Airbag Deployment Control: Circuit Short to Battery | GO to Pinpoint Test U |
| B1404:13 | Driver Side Airbag Deployment Control: Circuit Open | GO to Pinpoint Test U |
| B1404:1A | Driver Side Airbag Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test U |
| B1404:2B | Driver Side Airbag Deployment Control: Signal Cross Coupled | GO to Pinpoint Test AL |
| B1404:4A | Driver Side Airbag Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AM |
| B1405:11 | Driver Side Curtain Deployment Control 1: Circuit Short to Ground | GO to Pinpoint Test V |
| B1405:12 | Driver Side Curtain Deployment Control 1: Circuit Short to Battery | GO to Pinpoint Test V |
| B1405:13 | Driver Side Curtain Deployment Control 1: Circuit Open | GO to Pinpoint Test V |
| B1405:1A | Driver Side Curtain Deployment Control 1: Circuit Resistance Below Threshold | GO to Pinpoint Test V |
| B1405:2B | Driver Curtain Deployment Control 1: Signal Cross Coupled | GO to Pinpoint Test AL |
| B1405:4A | Driver Curtain Deployment Control 1: Incorrect Component Installed | GO to Pinpoint Test AM |
| B1407:11 | Passenger Side Airbag Deployment Control: Circuit Short to Ground | GO to Pinpoint Test W |
| B1407:12 | Passenger Side Airbag Deployment Control: Circuit Short to Battery | GO to Pinpoint Test W |
| B1407:13 | Passenger Side Airbag Deployment Control: Circuit Open | GO to Pinpoint Test W |
| B1407:1A | Passenger Side Airbag Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test W |
| B1407:2B | Passenger Side Airbag Deployment Control: Signal Cross Coupled | GO to Pinpoint Test AL |
| B1407:4A | Passenger Side Airbag Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AM |
| B1408:11 | Passenger Side Curtain Deployment Control 1: Circuit Short to Ground | GO to Pinpoint Test X |
| B1408:12 | Passenger Side Curtain Deployment Control 1: Circuit Short to Battery | GO to Pinpoint Test X |
| B1408:13 | Passenger Side Curtain Deployment Control 1: Circuit Open | GO to Pinpoint Test X |
| B1408:1A | Passenger Side Curtain Deployment Control 1: Circuit Resistance Below Threshold | GO to Pinpoint Test X |
| B1408:2B | Passenger Curtain Deployment Control 1: Signal Cross Coupled | GO to Pinpoint Test AL |
| B1408:4A | Passenger Curtain Deployment Control 1: Incorrect Component Installed | GO to Pinpoint Test AM |
| B140C:11 | Second Row Driver Side Seatbelt Sensor: Circuit Short to Ground | GO to Pinpoint Test Y |
| B140C:12 | Second Row Driver Side Seatbelt Sensor: Circuit Short to Battery | GO to Pinpoint Test Y |
| B140C:13 | Second Row Driver Side Seatbelt Sensor: Circuit Open | GO to Pinpoint Test Y |
| B140C:1D | Second Row Driver Side Seatbelt Sensor: Circuit Current Out of Range | GO to Pinpoint Test Y |
| B140C:2B | Second Row Driver Side Seatbelt Sensor: Signal Cross-Coupled | GO to Pinpoint Test AL |
| B140C:4A | Second Row Driver Side Seatbelt Sensor: Incorrect Component Installed | GO to Pinpoint Test AM |
| B140D:11 | Second Row Passenger Side Seatbelt Sensor: Circuit Short to Ground | GO to Pinpoint Test Z |
| B140D:12 | Second Row Passenger Side Seatbelt Sensor: Circuit Short to Battery | GO to Pinpoint Test Z |
| B140D:13 | Second Row Passenger Side Seatbelt Sensor: Circuit Open | GO to Pinpoint Test Z |
| B140D:1D | Second Row Passenger Side Seatbelt Sensor: Circuit Current Out of Range | GO to Pinpoint Test Z |
| B140D:2B | Second Row Passenger Side Seatbelt Sensor: Signal Cross-Coupled | GO to Pinpoint Test AL |
| B140D:4A | Second Row Passenger Side Seatbelt Sensor: Incorrect Component Installed | GO to Pinpoint Test AM |
| B1410:11 | Second Row Driver Side Seatbelt Pretensioner Deployment Control: Circuit Short To Ground | GO to Pinpoint Test AA |
| B1410:12 | Second Row Driver Side Seatbelt Pretensioner Deployment Control: Circuit Short To Battery | GO to Pinpoint Test AA |
| B1410:13 | Second Row Driver Side Seatbelt Pretensioner Deployment Control: Circuit Open | GO to Pinpoint Test AA |
| B1410:1A | Second Row Driver Side Seatbelt Pretensioner Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test AA |
| B1410:2B | Second Row Driver Side Seatbelt Pretensioner Deployment Control: Signal Cross-Coupled | GO to Pinpoint Test AL |
| B1410:4A | Second Row Driver Side Seatbelt Pretensioner Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AM |
| B1412:11 | Second Row Passenger Side Seatbelt Pretensioner Deployment Control: Circuit Short To Ground | GO to Pinpoint Test AB |
| B1412:12 | Second Row Passenger Side Seatbelt Pretensioner Deployment Control: Circuit Short To Battery | GO to Pinpoint Test AB |
| B1412:13 | Second Row Passenger Side Seatbelt Pretensioner Deployment Control: Circuit Open | GO to Pinpoint Test AB |
| B1412:1A | Second Row Passenger Side Seatbelt Pretensioner Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test AB |
| B1412:2B | Second Row Passenger Side Seatbelt Pretensioner Deployment Control: Signal Cross-Coupled | GO to Pinpoint Test AL |
| B1412:4A | Second Row Passenger Side Seatbelt Pretensioner Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AM |
| B1413:11 | Driver Frontal Restraints Sensor: Circuit Short To Ground | GO to Pinpoint Test AJ |
| B1413:12 | Driver Frontal Restraints Sensor: Circuit Short To Battery | GO to Pinpoint Test AJ |
| B1413:13 | Driver Frontal Restraints Sensor: Circuit Open | GO to Pinpoint Test AJ |
| B1413:4A | Driver Frontal Restraints Sensor: Incorrect Component Installed | GO to Pinpoint Test AM |
| B1413:81 | Driver Frontal Restraints Sensor: Invalid Serial Data Received | GO to Pinpoint Test AC |
| B1413:96 | Driver Frontal Restraints Sensor: Component Internal Failure | GO to Pinpoint Test AC |
| B1414:11 | Driver Side Restraints Sensor 1: Circuit Short to Ground | GO to Pinpoint Test AD |
| B1414:12 | Driver Side Restraints Sensor 1: Circuit Short to Battery | GO to Pinpoint Test AD |
| B1414:13 | Driver Side Restraints Sensor 1: Circuit Open | GO to Pinpoint Test AD |
| B1414:4A | Driver Side Restraints Sensor 1: Incorrect Component Installed | GO to Pinpoint Test AM |
| B1414:81 | Driver Side Restraints Sensor 1: Invalid Serial Data Received | GO to Pinpoint Test AC |
| B1414:96 | Driver Side Restraints Sensor 1: Component Internal Failure | GO to Pinpoint Test AC |
| B1415:11 | Driver Side Restraints Sensor 2: Circuit Short To Ground | GO to Pinpoint Test AE |
| B1415:11 | Driver Side Restraints Sensor 2: Circuit Short To Ground | GO to Pinpoint Test AH |
| B1415:12 | Driver Side Restraints Sensor 2: Circuit Short To Battery | GO to Pinpoint Test AE |
| B1415:12 | Driver Side Restraints Sensor 2: Circuit Short To Battery | GO to Pinpoint Test AH |
| B1415:13 | Driver Side Restraints Sensor 2: Circuit Open | GO to Pinpoint Test AE |
| B1415:13 | Driver Side Restraints Sensor 2: Circuit Open | GO to Pinpoint Test AH |
| B1415:4A | Driver Side Restraints Sensor 2: Incorrect Component Installed | GO to Pinpoint Test AM |
| B1415:81 | Driver Side Restraints Sensor 2: Invalid Serial Data Received | GO to Pinpoint Test AC |
| B1415:96 | Driver Side Restraints Sensor 2: Component Internal Failure | GO to Pinpoint Test AC |
| B1416:11 | Driver Side Restraints Sensor 3: Circuit Short To Ground | GO to Pinpoint Test AI |
| B1416:12 | Driver Side Restraints Sensor 3: Circuit Short To Battery | GO to Pinpoint Test AI |
| B1416:13 | Driver Side Restraints Sensor 3: Circuit Open | GO to Pinpoint Test AI |
| B1416:4A | Driver Side Restraints Sensor 3: Incorrect Component Installed | GO to Pinpoint Test AM |
| B1416:81 | Driver Side Restraints Sensor 3: Invalid Serial Data Received | GO to Pinpoint Test AC |
| B1416:96 | Driver Side Restraints Sensor 3: Component Internal Failure | GO to Pinpoint Test AC |
| B1417:11 | Passenger Frontal Restraints Sensor: Circuit Short To Ground | GO to Pinpoint Test AK |
| B1417:12 | Passenger Frontal Restraints Sensor: Circuit Short To Battery | GO to Pinpoint Test AK |
| B1417:13 | Passenger Frontal Restraints Sensor: Circuit Open | GO to Pinpoint Test AK |
| B1417:4A | Passenger Frontal Restraints Sensor: Incorrect Component Installed | GO to Pinpoint Test AM |
| B1417:81 | Passenger Frontal Restraints Sensor: Invalid Serial Data Received | GO to Pinpoint Test AC |
| B1417:96 | Passenger Frontal Restraints Sensor: Component Internal Failure | GO to Pinpoint Test AC |
| B1418:11 | Passenger Side Restraints Sensor 1: Circuit Short To Ground | GO to Pinpoint Test AF |
| B1418:12 | Passenger Side Restraints Sensor 1: Circuit Short To Battery | GO to Pinpoint Test AF |
| B1418:13 | Passenger Side Restraints Sensor 1: Circuit Open | GO to Pinpoint Test AF |
| B1418:4A | Passenger Side Restraints Sensor 1: Incorrect Component Installed | GO to Pinpoint Test AM |
| B1418:81 | Passenger Side Restraints Sensor 1: Invalid Serial Data Received | GO to Pinpoint Test AC |
| B1418:96 | Passenger Side Restraints Sensor 1: Component Internal Failure | GO to Pinpoint Test AC |
| B1419:11 | Passenger Side Restraints Sensor 2: Circuit Short To Ground | GO to Pinpoint Test AG |
| B1419:11 | Passenger Side Restraints Sensor 2: Circuit Short To Ground | GO to Pinpoint Test AI |
| B1419:12 | Passenger Side Restraints Sensor 2: Circuit Short To Battery | GO to Pinpoint Test AG |
| B1419:12 | Passenger Side Restraints Sensor 2: Circuit Short To Battery | GO to Pinpoint Test AI |
| B1419:13 | Passenger Side Restraints Sensor 2: Circuit Open | GO to Pinpoint Test AG |
| B1419:13 | Passenger Side Restraints Sensor 2: Circuit Open | GO to Pinpoint Test AI |
| B1419:4A | Passenger Side Restraints Sensor 2: Incorrect Component Installed | GO to Pinpoint Test AM |
| B1419:81 | Passenger Side Restraints Sensor 2: Invalid Serial Data Received | GO to Pinpoint Test AC |
| B1419:96 | Passenger Side Restraints Sensor 2: Component Internal Failure | GO to Pinpoint Test AC |
| B141A:11 | Passenger Side Restraints Sensor 3: Circuit Short To Ground | GO to Pinpoint Test AH |
| B141A:12 | Passenger Side Restraints Sensor 3: Circuit Short To Battery | GO to Pinpoint Test AH |
| B141A:13 | Passenger Side Restraints Sensor 3: Circuit Open | GO to Pinpoint Test AH |
| B141A:4A | Passenger Side Restraints Sensor 3: Incorrect Component Installed | GO to Pinpoint Test AM |
| B141A:81 | Passenger Side Restraints Sensor 3: Invalid Serial Data Received | GO to Pinpoint Test AC |
| B141A:96 | Passenger Side Restraints Sensor 3: Component Internal Failure | GO to Pinpoint Test AC |
| B142D:00 | Pyrotechnic End of Life Activation Performed: No Sub Type Information | GO to Pinpoint Test AV |
| B142D:00 | Pyrotechnic End of Life Activation Performed: No Sub Type Information | GO to Pinpoint Test AW |
| B1469:4A | Unused Satellite Restraints Sensor 1: Incorrect Component Installed | GO to Pinpoint Test AM |
| B146A:4A | Unused Satellite Restraints Sensor 2: Incorrect Component Installed | GO to Pinpoint Test AM |
| B1534:4A | Unused Deployable Device: Incorrect Component Installed | GO to Pinpoint Test AM |
| B1535:4A | Unused DC Sensor Device: Incorrect Component Installed | GO to Pinpoint Test AM |
| C0061:68 | Lateral Acceleration Sensor: Event Information | GO to Pinpoint Test AN |
| C0062:68 | Longitudinal Acceleration Sensor: Event Information | GO to Pinpoint Test AN |
| C0063:68 | Yaw Rate Sensor: Event Information | GO to Pinpoint Test AN |
| C0064:68 | Roll Rate Sensor: Event Information | GO to Pinpoint Test AN |
| C0065:68 | Vertical Acceleration Sensor: Event Information | GO to Pinpoint Test AN |
| U0028:08 | Vehicle Communication Bus A: Bus Signal/Message Failures | GO to Pinpoint Test AO |
| U0028:88 | Vehicle Communication Bus A: Bus Off | GO to Pinpoint Test AO |
| U0100:00 | Lost Communication with ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test AP |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test BF |
| U0140:00 | Lost Communication with Body Control Module: No Sub Type Information | GO to Pinpoint Test AQ |
| U0146:00 | Lost Communication with Gateway "A": No Sub Type Information | GO to Pinpoint Test AR |
| U0154:00 | Lost Communication with Restraints Occupant Classification System Module: No Sub Type Information | GO to Pinpoint Test AS |
| U0253:00 | Lost Communication with Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test AT |
| U0300:00 | Control Module: No Sub Type Information | GO to Pinpoint Test AV |
| U0401:00 | Invalid Data Received from ECM/PCM A: No Sub Type Information | GO to Pinpoint Test AU |
| U0401:81 | Invalid Data Received from ECM/PCM A: Invalid Serial Data Received | GO to Pinpoint Test AU |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | GO to Pinpoint Test AU |
| U0422:56 | Invalid Data Received From Body Control Module: Invalid/Incompatible Configuration | GO to Pinpoint Test AU |
| U0422:81 | Invalid Data Received From Body Control Module: Invalid Serial Data Received | GO to Pinpoint Test AU |
| U0422:92 | Invalid Data Received From Body Control Module: Performance Or Incorrect Operation | GO to Pinpoint Test AU |
| U0455:81 | Invalid Data Received From Restraints Occupant Classification System Module: Invalid Serial Data Received | GO to Pinpoint Test AU |
| U049A:00 | Invalid Data Received From "Door Control Module A": No Sub Type Information | GO to Pinpoint Test AU |
| U049A:81 | Invalid Data Received From "Door Control Module A": Invalid Serial Data Received | GO to Pinpoint Test AU |
| U049A:82 | Invalid Data Received From "Door Control Module A": Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test AU |
| U0501:00 | Invalid Data Received From "Door Control Module B": No Sub Type Information | GO to Pinpoint Test AU |
| U0501:81 | Invalid Data Received From "Door Control Module B": Invalid Serial Data Received | GO to Pinpoint Test AU |
| U0501:82 | Invalid Data Received From "Door Control Module B": Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test AU |
| U0554:00 | Invalid Data Received From Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test AU |
| U2024:51 | Control Module Cal-Config Data: Not Programmed | GO to Pinpoint Test AX |
| U2024:57 | Control Module Cal-Config Data: Invalid/Incompatible Software Component | GO to Pinpoint Test AV |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test AX |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | GO to Pinpoint Test AO |
| U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | GO to Pinpoint Test AV |
| U2300:55 | Central Configuration: Not Configured | GO to Pinpoint Test AY |
| U2300:64 | Central Configuration: Signal Plausibility Failure | GO to Pinpoint Test AY |
| U3000:04 | Control Module: System Internal Failure | GO to Pinpoint Test AV |
| U3000:46 | Control Module: Calibration / Parameter Memory Failure | GO to Pinpoint Test AV |
| U3000:49 | Control Module: Internal Electronic Failure | GO to Pinpoint Test AV |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AZ |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AZ |