| B1A67:12 |
Sensor Ground: Circuit Short To Battery |
GO to Pinpoint Test K |
| C103A:12 |
Pressure Sensor: Circuit Short To Battery |
GO to Pinpoint Test A |
| C103A:14 |
Pressure Sensor: Circuit Short To Ground Or Open |
GO to Pinpoint Test A |
| C103A:2A |
Pressure Sensor: Stuck in Range |
GO to Pinpoint Test A |
| C103A:62 |
Pressure Sensor: Signal Compare Failure |
GO to Pinpoint Test B |
| C103A:74 |
Pressure Sensor: Actuator Slipping |
GO to Pinpoint Test C |
| C103A:7A |
Pressure Sensor: Fluid Leak Or Seal Failure |
GO to Pinpoint Test D |
| C103A:7B |
Pressure Sensor: Low Fluid Level |
GO to Pinpoint Test E |
| C113A:62 |
Wakeup Control: Signal Compare Failure |
GO to Pinpoint Test F |
| C1A99:12 |
Pressure Sensor: Circuit Short To Battery |
GO to Pinpoint Test A |
| C1A99:14 |
Pressure Sensor: Circuit Short To Ground Or Open |
GO to Pinpoint Test A |
| C1A99:2A |
Pressure Sensor: Stuck in Range |
GO to Pinpoint Test A |
| C1B03:11 |
Directional Control Valve #1: Circuit Short To Ground |
GO to Pinpoint Test G |
| C1B03:12 |
Directional Control Valve #1: Circuit Short To Battery |
GO to Pinpoint Test G |
| C1B03:13 |
Directional Control Valve #1: Circuit Open |
GO to Pinpoint Test G |
| C1B03:1A |
Directional Control Valve #1: Circuit Resistance Below Threshold |
GO to Pinpoint Test H |
| C1B03:1B |
Directional Control Valve #1: Circuit Resistance Above Threshold |
GO to Pinpoint Test H |
| C1B03:62 |
Directional Control Valve #1: Signal Compare Failure |
GO to Pinpoint Test I |
| C1B03:67 |
Directional Control Valve #1: Signal Incorrect After Event |
GO to Pinpoint Test I |
| C1B07:11 |
Directional Control Valve #2: Circuit Short To Ground |
GO to Pinpoint Test G |
| C1B07:12 |
Directional Control Valve #2: Circuit Short To Battery |
GO to Pinpoint Test G |
| C1B07:13 |
Directional Control Valve #2: Circuit Open |
GO to Pinpoint Test G |
| C1B07:1A |
Directional Control Valve #2: Circuit Resistance Below Threshold |
GO to Pinpoint Test H |
| C1B07:1B |
Directional Control Valve #2: Circuit Resistance Above Threshold |
GO to Pinpoint Test H |
| C1B07:62 |
Directional Control Valve #2: Signal Compare Failure |
GO to Pinpoint Test I |
| C1B07:67 |
Directional Control Valve #2: Signal Incorrect After Event |
GO to Pinpoint Test I |
| C1B14:1C |
Sensor Supply Voltage A: Circuit Voltage Out Of Range |
GO to Pinpoint Test J |
| U0001:88 |
High Speed CAN Communication Bus: Bus Off |
GO to Pinpoint Test L |
| U0100:00 |
Lost Communication With ECM/PCM "A": No Sub Type Information |
GO to Pinpoint Test M |
| U011D:00 |
Lost Communication With All Wheel Drive Control Module: No Sub Type Information |
GO to Pinpoint Test M |
| U0121:00 |
Lost Communication With Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information |
GO to Pinpoint Test M |
| U0138:00 |
Lost Communication with All Terrain Control Module: No Sub Type Information |
GO to Pinpoint Test M |
| U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test M |
| U0401:00 |
Invalid Data Received from ECM/PCM A: No Sub Type Information |
GO to Pinpoint Test N |
| U0415:00 |
Invalid Data Received from Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information |
GO to Pinpoint Test N |
| U0415:82 |
Invalid Data Received from Anti-Lock Brake System (ABS) Control Module "A": Alive/Sequence Counter Incorrect/Not Updated |
GO to Pinpoint Test N |
| U0415:83 |
Invalid Data Received from Anti-Lock Brake System (ABS) Control Module "A": Value Of Signal Protection Calculation Incorrect |
GO to Pinpoint Test N |
| U041E:00 |
Invalid Data Received From All Wheel Drive Control Module: No Sub Type Information |
GO to Pinpoint Test N |
| U0422:00 |
Invalid Data Received From Body Control Module: No Sub Type Information |
GO to Pinpoint Test N |
| U0439:00 |
Invalid Data Received From All Terrain Control Module: No Sub Type Information |
GO to Pinpoint Test N |
| U2024:45 |
Control Module Cal-Config Data: Program Memory Failure |
GO to Pinpoint Test O |
| U2024:51 |
Control Module Cal-Config Data: Not Programmed |
GO to Pinpoint Test O |
| U2024:57 |
Control Module Cal-Config Data: Invalid/Incompatible Software Component |
GO to Pinpoint Test O |
| U3000:45 |
Control Module: Program Memory Failure |
GO to Pinpoint Test P |
| U3000:46 |
Control Module: Calibration/Parameter Memory Failure |
GO to Pinpoint Test P |
| U3000:47 |
Control Module: Watchdog/Safety μC Failure |
GO to Pinpoint Test P |
| U3000:48 |
Control Module: Supervision Software Failure |
GO to Pinpoint Test P |
| U3000:49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test P |
| U3000:4B |
Control Module: Over Temperature |
GO to Pinpoint Test Q |
| U3001:68 |
Control Module Improper Shutdown Performance: Event Information |
GO to Pinpoint Test R |
| U3003:16 |
Battery Voltage: Circuit Voltage Below Threshold |
GO to Pinpoint Test S |
| U3003:17 |
Battery Voltage: Circuit Voltage Above Threshold |
GO to Pinpoint Test T |