LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Ford >> 2022 >> EcoSport SES >> Repair and Diagnosis >> Heating, Ventilation & A/C (HVAC) >> HVAC Control Systems >> Climate Control System - General Information (Specifications, Description And Operation, Diagnosis And Testing) >> Diagnosis And Testing >> Climate Control System - Vehicles With: Electronic Manual Temperature Control (EMTC) >> Pinpoint Test(s) >> Pinpoint Test T: U0155:00
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Pinpoint Test T: U0155:00

  1. Refer to MANUAL CLIMATE CONTROL SYSTEM for schematic and connector information.

    Normal Operation and Fault Conditions 

    The HVAC uses information contained in messages from the IPC sent on the HS-CAN3 for 5 seconds.

    DTC Fault Trigger Conditions 

    DTC Description Fault Trigger Condition
    HVAC U0155:00 Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information This DTC sets in the HVAC module if data messages received from the IPC are missing.

    Possible Sources 

    • Vehicle communication bus
    • IPC
    • HVAC module

  2. T1 CHECK THE COMMUNICATION NETWORK

    • Ignition ON.

    • Using a diagnostic scan tool, perform network test.

    Does the IPC pass the network test? 

    Yes  GO to  T2
    No  REFER to: Communications Network .

  3. T2 RETRIEVE THE RECORDED DIAGNOSTIC TROUBLE CODES (DTCS) FROM THE INSTRUMENT PANEL CLUSTER (IPC) SELF-TEST

    • Using a diagnostic scan tool, perform IPC self-test.

    • Check for Diagnostic Trouble Codes (DTCs) from the IPC self-test.

    Is DTC U3003:16 or DTC U3003:17 recorded? 

    Yes  DIAGNOSE the battery voltage Diagnostic Trouble Codes (DTCs). REFER to: Instrumentation, Message Center and Warning Chimes .
    No  GO to  T3

  4. T3 RETRIEVE THE RECORDED DIAGNOSTIC TROUBLE CODES (DTCS) FROM THE HEATING, VENTILATION, AND AIR CONDITIONING (HVAC) CONTROL MODULE SELF-TEST

    • Check for recorded Diagnostic Trouble Codes (DTCs) from the HVAC module self-test.

    Is DTC U3003:16 or DTC U3003:17 recorded? 

    Yes  GO to Pinpoint Test Q 
    No  GO to  T4

  5. T4 RECHECK THE HEATING, VENTILATION, AND AIR CONDITIONING (HVAC) MODULE DIAGNOSTIC TROUBLE CODES (DTCS)

    • Clear all Diagnostic Trouble Codes (DTCs).

    • Ignition OFF.

    • Ignition ON.

    • Repeat the HVAC module self-test.

    Is DTC U0155:00 retrieved again? 

    Yes  GO to  T5
    No  The system is operating correctly at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.

  6. T5 CHECK FOR DIAGNOSTIC TROUBLE CODE (DTC) U0155:00 SET IN OTHER MODULES

    • Using a diagnostic scan tool, clear all Diagnostic Trouble Codes (DTCs).

    • Ignition OFF.

    • Wait 10 seconds.

    • Ignition ON.

    • Using a diagnostic scan tool, retrieve all Continuous Memory Diagnostic Trouble Codes (CMDTCs).

    Is DTC U0155:00 set in any other modules? 

    Yes  GO to  T6
    No  GO to  T7

  7. T6 CHECK FOR CORRECT INSTRUMENT PANEL CLUSTER (IPC) OPERATION

    • Ignition OFF.

    • Disconnect and inspect the IPC connector.

    • Repair:

      • corrosion (install new connector or terminals - clean module pins)
      • damaged or bent pins - install new terminals/pins
      • pushed-out pins - install new pins as necessary

    • Reconnect the IPC connector. Make sure it seats and latches correctly.

    • Operate the system and determine if the concern is still present.

    Is the concern still present? 

    Yes  CHECK OASIS for any applicable TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, INSTALL a new IPC. REFER to: Instrument Panel Cluster (IPC) .
    No  The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. ADDRESS the root cause of any connector or pin issues.

  8. T7 CHECK FOR CORRECT HVAC (HEATING, VENTILATION AND AIR CONDITIONING) CONTROL MODULE OPERATION

    • Ignition OFF.

    • Disconnect and inspect all HVAC control module electrical connectors (if not previously disconnected).

    • Repair:

      • corrosion (install new connector or terminal - clean module pins)
      • damaged or bent pins - install new terminals or pins
      • pushed-out pins - install new pins as necessary

    • Connect all HVAC control module electrical connectors. Make sure they seat and latch correctly.

    • Operate the system and determine if the concern is still present.

    Is the concern still present? 

    Yes  CHECK OASIS for any applicable TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, INSTALL a new HVAC control module. REFER to: Heating, Ventilation and Air Conditioning (HVAC) Control Module .
    No  The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. ADDRESS the root cause of any connector or pin issues.
scientia non olet · About LEMON Manuals