Lane Keeping System DTCS
Diagnostics in this information assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
| DTC | Description | Action |
|---|---|---|
| C0072:00 | Brake Temperature Too High: No Sub Type Information | GO to Pinpoint Test V |
| U0405:64 | Invalid Data Received From Cruise Control Module: Signal Plausibility Failure | GO to Pinpoint Test AD |
| U0416:86 | Invalid Data Received From Vehicle Dynamics Control Module: Signal Invalid | GO to Pinpoint Test AE |
| U0232:00 | Lost Communication With Side Obstacle Detection Control Module "A": No Sub Type Information | GO to Pinpoint Test I |
| U0404:86 | Invalid Data Received from Gear Shift Control Module A: Signal Invalid | GO to Pinpoint Test AC |
| U0122:00 | Lost Communication With Vehicle Dynamics Control Module: No Sub Type Information | GO to Pinpoint Test T |
| U0130:00 | Lost Communication With Steering Effort Control Module: No Sub Type Information | GO to Pinpoint Test U |
| B120C:11 | Heater for Windshield Mounted Sensor: Circuit Short To Ground | GO to Pinpoint Test C |
| B120C:13 | Heater for Windshield Mounted Sensor: Circuit Open | GO to Pinpoint Test C |
| B13A6:14 | Lane Departure Warning (LDW) Switch Input: Circuit Short To Ground Or Open | GO to Pinpoint Test A |
| C1001:54 | Vision System Camera: Missing Calibration | GO to Pinpoint Test W |
| C1001:78 | Vision System Camera: Alignment Or Adjustment Incorrect | GO to Pinpoint Test W |
| C1001:97 | Vision System Camera: Component Or System Operation Obstructed Or Blocked | GO to Pinpoint Test X |
| C1001:98 | Vision System Camera: Component Or System Over Temperature | GO to Pinpoint Test Y |
| C1A67:08 | Forward Looking Sensor: Bus Signal/Message Failures | GO to Pinpoint Test Z |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test E |
| U0101:00 | Lost Communication with TCM: No Sub Type Information | GO to Pinpoint Test F |
| U0103:00 | Lost Communication With Gear Shift Control Module A: No Sub Type Information | GO to Pinpoint Test G |
| U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information | GO to Pinpoint Test H |
| U0131:00 | Lost Communication With Power Steering Control Module "A": No Sub Type Information | GO to Pinpoint Test K |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test M |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to Pinpoint Test N |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test O |
| U0158:00 | Lost Communication With Head Up Display: No Sub Type Information | GO to Pinpoint Test L |
| U0212:00 | Lost Communication With Steering Column Control Module: No Sub Type Information | GO to Pinpoint Test P |
| U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test Q |
| U0401:86 | Invalid Data Received from ECM/PCM A: Signal Invalid | GO to Pinpoint Test AA |
| U0418:86 | Invalid Data Received from Brake System Control Module "A": Signal Invalid | GO to Pinpoint Test AF |
| U0423:82 | Invalid Data Received from Instrument Panel Cluster Control Module: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test AJ |
| U0423:86 | Invalid Data Received from Instrument Panel Cluster Control Module: Signal Invalid | GO to Pinpoint Test AJ |
| U1000:11 | Solid State Driver Protection Active -Driver Disabled: Circuit Short To Ground | GO to Pinpoint Test AO |
| U2018:51 | Control Module Software #3: Not Programmed | GO to Pinpoint Test AP |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test AQ |
| U2101:64 | Control Module Configuration Incompatible: Signal Plausibility Failure | GO to Pinpoint Test AR |
| U2300:55 | Central Configuration: Not Configured | GO to Pinpoint Test AS |
| U2300:64 | Central Configuration: Signal Plausibility Failure | GO to Pinpoint Test AT |
| U3000:41 | Control Module: General Checksum Failure | GO to Pinpoint Test AU |
| U3000:42 | Control Module: General Memory Failure | GO to Pinpoint Test AV |
| U3000:44 | Control Module: Data Memory Failure | GO to Pinpoint Test AW |
| U3000:49 | Control Module: Internal Electronic Failure | GO to Pinpoint Test AW |
| U3000:64 | Control Module: Signal Plausibility Failure | GO to Pinpoint Test AX |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test R |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test S |
| U0233:00 | Lost Communication With Side Obstacle Detection Control Module "B": No Sub Type Information | GO to Pinpoint Test J |
| U0420:86 | Invalid Data Received from Power Steering Control Module "A": Signal Invalid | GO to Pinpoint Test AH |
| U0422:82 | Invalid Data Received From Body Control Module: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test AI |
| U0452:86 | Invalid Data Received From Restraints Control Module: Signal Invalid | GO to Pinpoint Test AL |
| U0419:86 | Invalid Data Received From Steering Effort Control Module: Signal Invalid | GO to Pinpoint Test AG |
| U0429:86 | Invalid Data Received From Steering Column Control Module: Signal Invalid | GO to Pinpoint Test AK |
| U0533:86 | Invalid Data Received From Side Obstacle Detection Control Module "A": Signal Invalid | GO to Pinpoint Test AM |
| U0534:86 | Invalid Data Received From Side Obstacle Detection Control Module "B": Signal Invalid | GO to Pinpoint Test AN |
| U0402:86 | Invalid Data Received from TCM: Signal Invalid | GO to Pinpoint Test AB |