Power Steering System DTCS
Diagnostics in this information assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
| DTC | Description | Action |
|---|---|---|
| C0051:23 | Steering Wheel Position Sensor: Signal Stuck Low | GO to Pinpoint Test AG |
| C0051:27 | Steering Wheel Position Sensor: Signal Rate Of Change Above Threshold | GO to Pinpoint Test AG |
| C0051:28 | Steering Wheel Position Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure | GO to Pinpoint Test AG |
| C0051:41 | Steering Wheel Position Sensor: General Checksum Failure | GO to Pinpoint Test AG |
| C0051:54 | Steering Wheel Position Sensor: Missing Calibration | GO to Pinpoint Test AG |
| C0051:62 | Steering Wheel Position Sensor: Signal Compare Failure | GO to Pinpoint Test AG |
| C0051:64 | Steering Wheel Position Sensor: Signal Plausibility Failure | GO to Pinpoint Test AG |
| C0051:67 | Steering Wheel Position Sensor: Signal Incorrect After Event | GO to Pinpoint Test AG |
| C0051:85 | Steering Wheel Position Sensor: Signal Above Allowable Range | GO to Pinpoint Test AG |
| C0051:86 | Steering Wheel Position Sensor: Signal Invalid | GO to Pinpoint Test AG |
| C006B:00 | Stability System Active Too Long: No Sub Type Information | GO to Pinpoint Test AG |
| B1D23:4B | Overheat Sensor: Over Temperature | GO to Pinpoint Test BB |
| C102D:00 | High Friction Inside Power Steering: No Sub Type Information | GO to Pinpoint Test AI |
| C1110:56 | Power steering Calibration Data: Invalid/Incompatible Configuration | GO to Pinpoint Test AA |
| C1B00:49 | Steering Angle Sensor: Internal Electronic Failure | GO to Pinpoint Test BF |
| C1B00:62 | Steering Angle Sensor: Signal Compare Failure | GO to Pinpoint Test BF |
| C200B:49 | Steering Shaft Torque Sensor 1: Internal Electronic Failure | GO to Pinpoint Test BG |
| C200B:62 | Steering Shaft Torque Sensor 1: Signal Compare Failure | GO to Pinpoint Test BG |
| C200C:49 | Steering Shaft Torque Sensor 2: Internal Electronic Failure | GO to Pinpoint Test BH |
| C200C:62 | Steering Shaft Torque Sensor 2: Signal Compare Failure | GO to Pinpoint Test BH |
| C200D:49 | Motor Rotation Angle Sensor: Internal Electronic Failure | GO to Pinpoint Test BI |
| C200D:62 | Motor Rotation Angle Sensor: Signal Compare Failure | GO to Pinpoint Test BI |
| P0635:68 | Power Steering Control Circuit: Event Information | GO to Pinpoint Test D |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test AJ |
| U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information | GO to Pinpoint Test AK |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test AL |
| U0146:00 | Lost Communication With Serial Data Gateway "A": No Sub Type Information | GO to Pinpoint Test AM |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to Pinpoint Test AN |
| U0159:00 | Lost Communication With Parking Assist Control Module "A": No Sub Type Information | GO to Pinpoint Test AP |
| U023A:00 | Lost Communication With Image Processing Module A: No Sub Type Information | GO to Pinpoint Test AR |
| U0415:00 | Invalid Data Received from Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information | GO to Pinpoint Test AT |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | GO to Pinpoint Test BU |
| U0452:00 | Invalid Data Received From Restraints Control Module: No Sub Type Information | GO to Pinpoint Test BX |
| U053B:00 | Invalid Data Received From Image Processing Module A: No Sub Type Information | GO to Pinpoint Test AX |
| U2014:68 | Control Module Hardware: Event Information | GO to Pinpoint Test E |
| U2016:47 | Control Module Main Software: Watchdog/Safety μC Failure | GO to Pinpoint Test BO |
| U2016:48 | Control Module Main Software: Supervision Software Failure | GO to Pinpoint Test BO |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test BQ |
| U3000:42 | Control Module: General Memory Failure | GO to Pinpoint Test B |
| U3000:49 | Control Module: Internal Electronic Failure | GO to Pinpoint Test B |
| U3000:96 | Control Module: Component Internal Failure | GO to Pinpoint Test B |
| U3001:68 | Control Module Improper Shutdown Performance: Event Information | GO to Pinpoint Test BD |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test BC |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test BC |
| U3003:19 | Battery Voltage: Circuit Current Above Threshold | GO to Pinpoint Test BC |
| U3003:68 | Battery Voltage: Event Information | GO to Pinpoint Test BC |
| U3003:A2 | Battery Voltage: System Voltage Low | GO to Pinpoint Test BC |