Supplemental Restraint System DTCS
Diagnostics in this information assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
NOTE:
Unlisted Diagnostic Trouble Codes (DTCs)
are often retrieved as a result of incorrect repair procedures. Before attempting any repairs for unlisted Diagnostic Trouble Codes (DTCs), check the vehicle service history for recent repairs. For RCM Diagnostic Trouble Codes (DTCs) not listed in this chart,
- Repair all other RCM Diagnostic Trouble Codes (DTCs) before attempting to repair any Diagnostic Trouble Codes (DTCs) not listed in this chart.
- If no other RCM Diagnostic Trouble Codes (DTCs) are retrieved, CLEAR the RCM Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If the RCM Diagnostic Trouble Codes (DTCs) return, VERIFY that the RCM is the correct part number for the vehicle application, and INSTALL As-Built data following scan tool instructions under Module Programming > As-Built.
- Inspect the RCM and RCM connectors for any damaged pins or connections.
| DTC | Description | Action |
|---|---|---|
| B00A0:11 | Occupant Classification System: Circuit Short to Ground | GO to Pinpoint Test BM |
| B00A0:12 | Occupant Classification System: Circuit Short to Battery | GO to Pinpoint Test BM |
| B1123:11 | Restraints Ignition Relay: Circuit Short to Ground | GO to Pinpoint Test BM |
| B1123:12 | Restraints Ignition Relay: Circuit Short to Battery | GO to Pinpoint Test BM |
| B11D8:01 | Restraint Event Notification: General Electrical Failure | GO to Pinpoint Test V |
| B0061:11 | Passenger Seatbelt Tension Sensor: Circuit Short to Ground | GO to Pinpoint Test BB |
| B0061:12 | Passenger Seatbelt Tension Sensor: Circuit Short to Battery | GO to Pinpoint Test BB |
| B0061:13 | Passenger Seatbelt Tension Sensor: Circuit Open | GO to Pinpoint Test BB |
| B0061:64 | Passenger Seatbelt Tension Sensor: Signal Plausibility Failure | GO to Pinpoint Test BB |
| B00A0:62 | Occupant Classification System: Signal Compare Failure | GO to Pinpoint Test BC |
| B00C0:11 | Passenger Seat Occupant Classification Sensor "A": Circuit Short To Ground | GO to Pinpoint Test BD |
| B00C0:12 | Passenger Seat Occupant Classification Sensor "A": Circuit Short To Battery | GO to Pinpoint Test BD |
| B00C0:16 | Passenger Seat Occupant Classification Sensor "A": Circuit Voltage Below Threshold | GO to Pinpoint Test BD |
| B00C0:49 | Passenger Seat Occupant Classification Sensor "A": Internal Electronic Failure | GO to Pinpoint Test BD |
| B00C0:7B | Passenger Seat Occupant Classification Sensor "A": Low Fluid Level | GO to Pinpoint Test BD |
| B00C2:11 | Passenger Seat Occupant Classification Sensor "C": Circuit Short to Ground | GO to Pinpoint Test BE |
| B00C2:12 | Passenger Seat Occupant Classification Sensor "C": Circuit Short to Battery | GO to Pinpoint Test BE |
| B1193:00 | Crash Event Storage Full and Locked: No Sub Type Information | GO to Pinpoint Test BF |
| U0100:00 | Lost Communication with ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test BG |
| U0151:00 | Lost Communication with Restraints Control Module: No Sub Type Information | GO to Pinpoint Test BH |
| U024C:00 | Lost Communication with Seat Control Module "H": No Sub Type Information | GO to Pinpoint Test BI |
| U0401:00 | Invalid Data Received from ECM/PCM A: No Sub Type Information | GO to Pinpoint Test BJ |
| U3000:41 | Control Module: General Checksum Failure | GO to Pinpoint Test BK |
| U3000:42 | Control Module: General Memory Failure | GO to Pinpoint Test BK |
| U3000:46 | Control Module: Special Memory Failure | GO to Pinpoint Test BK |
| U3000:54 | Control Module: Missing Calibration | GO to Pinpoint Test BL |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test BA |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test BA |
| B0001:11 | Driver Frontal Stage 1 Deployment Control: Circuit Short to Ground | GO to Pinpoint Test A |
| B0001:12 | Driver Frontal Stage 1 Deployment Control: Circuit Short to Battery | GO to Pinpoint Test A |
| B0001:13 | Driver Frontal Stage 1 Deployment Control: Circuit Open | GO to Pinpoint Test A |
| B0001:1A | Driver Frontal Stage 1 Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test A |
| B0001:2B | Driver Frontal Stage 1 Deployment Control: Signal Cross Coupled | GO to Pinpoint Test AM |
| B0001:4A | Driver Frontal Stage 1 Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AN |
| B0002:11 | Driver Frontal Stage 2 Deployment Control: Circuit Short to Ground | GO to Pinpoint Test B |
| B0002:12 | Driver Frontal Stage 2 Deployment Control: Circuit Short to Battery | GO to Pinpoint Test B |
| B0002:13 | Driver Frontal Stage 2 Deployment Control: Circuit Open | GO to Pinpoint Test B |
| B0002:1A | Driver Frontal Stage 2 Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test B |
| B0002:2B | Driver Frontal Stage 2 Deployment Control: Signal Cross Coupled | GO to Pinpoint Test AM |
| B0002:4A | Driver Frontal Stage 2 Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AN |
| B0004:11 | Driver Knee Bolster Deployment Control: Circuit Short to Ground | GO to Pinpoint Test C |
| B0004:12 | Driver Knee Bolster Deployment Control: Circuit Short to Battery | GO to Pinpoint Test C |
| B0004:13 | Driver Knee Bolster Deployment Control: Circuit Open | GO to Pinpoint Test C |
| B0004:1A | Driver Knee Bolster Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test C |
| B0004:2B | Driver Knee Bolster Deployment Control: Signal Cross Coupled | GO to Pinpoint Test AM |
| B0010:11 | Passenger Frontal Stage 1 Deployment Control: Circuit Short to Ground | GO to Pinpoint Test D |
| B0010:12 | Passenger Frontal Stage 1 Deployment Control: Circuit Short to Battery | GO to Pinpoint Test D |
| B0010:13 | Passenger Frontal Stage 1 Deployment Control: Circuit Open | GO to Pinpoint Test D |
| B0010:1A | Passenger Frontal Stage 1 Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test D |
| B0010:2B | Passenger Frontal Stage 1 Deployment Control: Signal Cross Coupled | GO to Pinpoint Test AM |
| B0010:4A | Passenger Frontal Stage 1 Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AN |
| B0011:11 | Passenger Frontal Stage 2 Deployment Control: Circuit Short to Ground | GO to Pinpoint Test E |
| B0011:12 | Passenger Frontal Stage 2 Deployment Control: Circuit Short to Battery | GO to Pinpoint Test E |
| B0011:13 | Passenger Frontal Stage 2 Deployment Control: Circuit Open | GO to Pinpoint Test E |
| B0011:1A | Passenger Frontal Stage 2 Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test E |
| B0011:2B | Passenger Frontal Stage 2 Deployment Control: Signal Cross-Coupled | GO to Pinpoint Test AM |
| B0011:4A | Passenger Frontal Stage 2 Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AN |
| B0013:11 | Passenger Knee Bolster Deployment Control: Circuit Short to Ground | GO to Pinpoint Test F |
| B0013:12 | Passenger Knee Bolster Deployment Control: Circuit Short to Battery | GO to Pinpoint Test F |
| B0013:13 | Passenger Knee Bolster Deployment Control: Circuit Open | GO to Pinpoint Test F |
| B0013:1A | Passenger Knee Bolster Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test F |
| B0013:2B | Passenger Knee Bolster Deployment Control: Signal Cross-Coupled | GO to Pinpoint Test AM |
| B0013:4A | Passenger Knee Bolster Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AN |
| B0050:11 | Driver Seatbelt Sensor: Circuit Short to Ground | GO to Pinpoint Test G |
| B0050:12 | Driver Seatbelt Sensor: Circuit Short to Battery | GO to Pinpoint Test G |
| B0050:13 | Driver Seatbelt Sensor: Circuit Open | GO to Pinpoint Test G |
| B0050:1D | Driver Seatbelt Sensor: Circuit Current Out of Range | GO to Pinpoint Test G |
| B0050:2B | Driver Seatbelt Sensor: Signal Cross-Coupled | GO to Pinpoint Test AM |
| B0050:4A | Driver Seatbelt Sensor: Incorrect Component Installed | GO to Pinpoint Test AN |
| B0052:11 | Passenger Seatbelt Sensor: Circuit Short to Ground | GO to Pinpoint Test H |
| B0052:12 | Passenger Seatbelt Sensor: Circuit Short to Battery | GO to Pinpoint Test H |
| B0052:13 | Passenger Seatbelt Sensor: Circuit Open | GO to Pinpoint Test H |
| B0052:1D | Passenger Seatbelt Sensor: Circuit Current Out of Range | GO to Pinpoint Test H |
| B0052:2B | Passenger Seatbelt Sensor: Signal Cross-Coupled | GO to Pinpoint Test AM |
| B0052:4A | Passenger Seatbelt Sensor: Incorrect Component Installed | GO to Pinpoint Test AN |
| B0054:11 | Second Row Center Seatbelt Sensor: Circuit Short To Ground | GO to Pinpoint Test I |
| B0054:12 | Second Row Center Seatbelt Sensor: Circuit Short To Battery | GO to Pinpoint Test I |
| B0054:13 | Second Row Center Seatbelt Sensor: Circuit Open | GO to Pinpoint Test I |
| B0054:1D | Second Row Center Seatbelt Sensor: Circuit Current Out Of Range | GO to Pinpoint Test I |
| B0054:2B | Second Row Center Seatbelt Sensor: Signal Cross Coupled | GO to Pinpoint Test AM |
| B0054:4A | Second Row Center Seatbelt Sensor: Incorrect Component Installed | GO to Pinpoint Test AN |
| B0070:11 | Driver Seatbelt Pretensioner "A" Deployment Control: Circuit Short to Ground | GO to Pinpoint Test J |
| B0070:12 | Driver Seatbelt Pretensioner "A" Deployment Control: Circuit Short to Battery | GO to Pinpoint Test J |
| B0070:13 | Driver Seatbelt Pretensioner "A" Deployment Control: Circuit Open | GO to Pinpoint Test J |
| B0070:1A | Driver Seatbelt Pretensioner "A" Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test J |
| B0070:2B | Driver Seatbelt Pretensioner "A" Deployment Control: Signal Cross Coupled | GO to Pinpoint Test AM |
| B0070:4A | Driver Seatbelt Pretensioner "A" Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AN |
| B0072:11 | Passenger Seatbelt Pretensioner "A" Deployment Control: Circuit Short to Ground | GO to Pinpoint Test K |
| B0072:12 | Passenger Seatbelt Pretensioner "A" Deployment Control: Circuit Short to Battery | GO to Pinpoint Test K |
| B0072:13 | Passenger Seatbelt Pretensioner "A" Deployment Control: Circuit Open | GO to Pinpoint Test K |
| B0072:1A | Passenger Seatbelt Pretensioner "A" Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test K |
| B0072:2B | Passenger Seatbelt Pretensioner "A" Deployment Control: Signal Cross Coupled | GO to Pinpoint Test AM |
| B0072:4A | Passenger Seatbelt Pretensioner "A" Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AN |
| B007E:11 | Driver Seatbelt Pretensioner "C" Deployment Control: Circuit Short to Ground | GO to Pinpoint Test L |
| B007E:12 | Driver Seatbelt Pretensioner "C" Deployment Control: Circuit Short to Battery | GO to Pinpoint Test L |
| B007E:13 | Driver Seatbelt Pretensioner "C" Deployment Control: Circuit Open | GO to Pinpoint Test L |
| B007E:1A | Driver Seatbelt Pretensioner "C" Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test L |
| B007E:2B | Driver Seatbelt Pretensioner "C" Deployment Control: Signal Cross-Coupled | GO to Pinpoint Test AM |
| B007E:4A | Driver Seatbelt Pretensioner "C" Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AN |
| B007F:11 | Passenger Seatbelt Pretensioner "C" Deployment Control: Circuit Short to Ground | GO to Pinpoint Test M |
| B007F:12 | Passenger Seatbelt Pretensioner "C" Deployment Control: Circuit Short to Battery | GO to Pinpoint Test M |
| B007F:13 | Passenger Seatbelt Pretensioner "C" Deployment Control: Circuit Open | GO to Pinpoint Test M |
| B007F:1A | Passenger Seatbelt Pretensioner "C" Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test M |
| B007F:2B | Passenger Seatbelt Pretensioner "C" Deployment Control: Signal Cross-Coupled | GO to Pinpoint Test AM |
| B007F:4A | Passenger Seatbelt Pretensioner "C" Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AN |
| B0082:11 | Passenger Seatbelt Load Limiter Deployment Control: Circuit Short to Ground | GO to Pinpoint Test N |
| B0082:12 | Passenger Seatbelt Load Limiter Deployment Control: Circuit Short to Battery | GO to Pinpoint Test N |
| B0082:13 | Passenger Seatbelt Load Limiter Deployment Control: Circuit Open | GO to Pinpoint Test N |
| B0082:1A | Passenger Seatbelt Load Limiter Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test N |
| B0082:2B | Passenger Seatbelt Load Limiter Deployment Control: Signal Cross Coupled | GO to Pinpoint Test AM |
| B0082:4A | Passenger Seatbelt Load Limiter Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AN |
| B00A0:09 | Occupant Classification System: Component Failure | GO to Pinpoint Test O |
| B00A0:4A | Occupant Classification System: Incorrect Component Installed | GO to Pinpoint Test AN |
| B00A0:63 | Occupant Classification System: Circuit / Component Protection Time-Out | GO to Pinpoint Test O |
| B00A0:64 | Occupant Classification System: Signal Plausibility Failure | GO to Pinpoint Test O |
| B00A0:68 | Occupant Classification System: Event Information | GO to Pinpoint Test O |
| B00B5:11 | Driver Seat Track Position Restraints Sensor: Circuit Short to Ground | GO to Pinpoint Test P |
| B00B5:12 | Driver Seat Track Position Restraints Sensor: Circuit Short to Battery | GO to Pinpoint Test P |
| B00B5:13 | Driver Seat Track Position Restraints Sensor: Circuit Open | GO to Pinpoint Test P |
| B00B5:1D | Driver Seat Track Position Restraints Sensor: Circuit Current Out of Range | GO to Pinpoint Test P |
| B00B5:2B | Driver Seat Track Position Restraints Sensor: Signal Cross Coupled | GO to Pinpoint Test AM |
| B00B5:4A | Driver Seat Track Position Restraints Sensor: Incorrect Component Installed | GO to Pinpoint Test AN |
| B00C5:11 | Passenger Seat Track Position Restraints Sensor: Circuit Short to Ground | GO to Pinpoint Test Q |
| B00C5:12 | Passenger Seat Track Position Restraints Sensor: Circuit Short to Battery | GO to Pinpoint Test Q |
| B00C5:13 | Passenger Seat Track Position Restraints Sensor: Circuit Open | GO to Pinpoint Test Q |
| B00C5:1D | Passenger Seat Track Position Restraints Sensor: Circuit Current Out of Range | GO to Pinpoint Test Q |
| B00C5:2B | Passenger Seat Track Position Restraints Sensor: Signal Cross Coupled | GO to Pinpoint Test AM |
| B00C5:4A | Passenger Seat Track Position Restraints Sensor: Incorrect Component Installed | GO to Pinpoint Test AN |
| B00D5:01 | Restraint System Passenger Disable Indicator: General Electrical Failure | GO to Pinpoint Test R |
| B00D5:11 | Restraint System Passenger Disable Indicator: Circuit Short To Ground | GO to Pinpoint Test S |
| B00D5:12 | Restraint System Passenger Disable Indicator: Circuit Short To Battery | GO to Pinpoint Test S |
| B00D5:13 | Restraint System Passenger Disable Indicator: Circuit Open | GO to Pinpoint Test S |
| B00D5:4A | Restraint System Passenger Disable Indicator: Incorrect Component Installed | GO to Pinpoint Test AN |
| B1193:00 | Crash Event Storage Full and Locked: No Sub Type Information | GO to Pinpoint Test T |
| B11CF:11 | Passenger Frontal Airbag Canister Vent: Circuit Short to Ground | GO to Pinpoint Test U |
| B11CF:12 | Passenger Frontal Airbag Canister Vent: Circuit Short to Battery | GO to Pinpoint Test U |
| B11CF:13 | Passenger Frontal Airbag Canister Vent: Circuit Open | GO to Pinpoint Test U |
| B11CF:1A | Passenger Frontal Airbag Canister Vent: Circuit Resistance Below Threshold | GO to Pinpoint Test U |
| B11CF:2B | Passenger Frontal Airbag Canister Vent: Signal Cross Coupled | GO to Pinpoint Test AM |
| B11CF:4A | Passenger Frontal Airbag Canister Vent: Incorrect Component Installed | GO to Pinpoint Test AN |
| B11D8:11 | Restraint Event Notification: Circuit Short To Ground | GO to Pinpoint Test V |
| B11D8:12 | Restraint Event Notification: Circuit Short To Battery | GO to Pinpoint Test V |
| B11D8:13 | Restraint Event Notification: Circuit Short To Open | GO to Pinpoint Test V |
| B1202:01 | Restraint System Passenger Enable Indicator: General Electrical Failure | GO to Pinpoint Test R |
| B1202:11 | Restraint System Passenger Enable Indicator: Circuit Short To Ground | GO to Pinpoint Test W |
| B1202:12 | Restraint System Passenger Enable Indicator: Circuit Short To Battery | GO to Pinpoint Test W |
| B1202:13 | Restraint System Passenger Enable Indicator: Circuit Open | GO to Pinpoint Test W |
| B1202:4A | Restraint System Passenger Enable Indicator: Incorrect Component Installed | GO to Pinpoint Test AN |
| B1404:11 | Driver Side Airbag Deployment Control: Circuit Short to Ground | GO to Pinpoint Test X |
| B1404:12 | Driver Side Airbag Deployment Control: Circuit Short to Battery | GO to Pinpoint Test X |
| B1404:13 | Driver Side Airbag Deployment Control: Circuit Open | GO to Pinpoint Test X |
| B1404:1A | Driver Side Airbag Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test X |
| B1404:2B | Driver Side Airbag Deployment Control: Signal Cross Coupled | GO to Pinpoint Test AM |
| B1404:4A | Driver Side Airbag Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AN |
| B1405:11 | Driver Side Curtain Deployment Control 1: Circuit Short to Ground | GO to Pinpoint Test Y |
| B1405:12 | Driver Side Curtain Deployment Control 1: Circuit Short to Battery | GO to Pinpoint Test Y |
| B1405:13 | Driver Side Curtain Deployment Control 1: Circuit Open | GO to Pinpoint Test Y |
| B1405:1A | Driver Side Curtain Deployment Control 1: Circuit Resistance Below Threshold | GO to Pinpoint Test Y |
| B1405:2B | Driver Curtain Deployment Control 1: Signal Cross Coupled | GO to Pinpoint Test AM |
| B1405:4A | Driver Curtain Deployment Control 1: Incorrect Component Installed | GO to Pinpoint Test AN |
| B1407:11 | Passenger Side Airbag Deployment Control: Circuit Short to Ground | GO to Pinpoint Test Z |
| B1407:12 | Passenger Side Airbag Deployment Control: Circuit Short to Battery | GO to Pinpoint Test Z |
| B1407:13 | Passenger Side Airbag Deployment Control: Circuit Open | GO to Pinpoint Test Z |
| B1407:1A | Passenger Side Airbag Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test Z |
| B1407:2B | Passenger Side Airbag Deployment Control: Signal Cross Coupled | GO to Pinpoint Test AM |
| B1407:4A | Passenger Side Airbag Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AN |
| B1408:11 | Passenger Side Curtain Deployment Control 1: Circuit Short to Ground | GO to Pinpoint Test AA |
| B1408:12 | Passenger Side Curtain Deployment Control 1: Circuit Short to Battery | GO to Pinpoint Test AA |
| B1408:13 | Passenger Side Curtain Deployment Control 1: Circuit Open | GO to Pinpoint Test AA |
| B1408:1A | Passenger Side Curtain Deployment Control 1: Circuit Resistance Below Threshold | GO to Pinpoint Test AA |
| B1408:2B | Passenger Curtain Deployment Control 1: Signal Cross Coupled | GO to Pinpoint Test AM |
| B1408:4A | Passenger Curtain Deployment Control 1: Incorrect Component Installed | GO to Pinpoint Test AN |
| B140C:11 | Second Row Driver Side Seatbelt Sensor: Circuit Short to Ground | GO to Pinpoint Test AB |
| B140C:12 | Second Row Driver Side Seatbelt Sensor: Circuit Short to Battery | GO to Pinpoint Test AB |
| B140C:13 | Second Row Driver Side Seatbelt Sensor: Circuit Open | GO to Pinpoint Test AB |
| B140C:1D | Second Row Driver Side Seatbelt Sensor: Circuit Current Out of Range | GO to Pinpoint Test AB |
| B140C:2B | Second Row Driver Side Seatbelt Sensor: Signal Cross-Coupled | GO to Pinpoint Test AM |
| B140C:4A | Second Row Driver Side Seatbelt Sensor: Incorrect Component Installed | GO to Pinpoint Test AN |
| B140D:11 | Second Row Passenger Side Seatbelt Sensor: Circuit Short to Ground | GO to Pinpoint Test AC |
| B140D:12 | Second Row Passenger Side Seatbelt Sensor: Circuit Short to Battery | GO to Pinpoint Test AC |
| B140D:13 | Second Row Passenger Side Seatbelt Sensor: Circuit Open | GO to Pinpoint Test AC |
| B140D:1D | Second Row Passenger Side Seatbelt Sensor: Circuit Current Out of Range | GO to Pinpoint Test AC |
| B140D:2B | Second Row Passenger Side Seatbelt Sensor: Signal Cross-Coupled | GO to Pinpoint Test AM |
| B140D:4A | Second Row Passenger Side Seatbelt Sensor: Incorrect Component Installed | GO to Pinpoint Test AN |
| B140E:11 | Third Row Driver Side Seatbelt Sensor: Circuit Short To Ground | GO to Pinpoint Test AD |
| B140E:12 | Third Row Driver Side Seatbelt Sensor: Circuit Short To Battery | GO to Pinpoint Test AD |
| B140E:13 | Third Row Driver Side Seatbelt Sensor: Circuit Open | GO to Pinpoint Test AD |
| B140E:1D | Third Row Driver Side Seatbelt Sensor: Circuit Current Out Of Range | GO to Pinpoint Test AD |
| B140E:2B | Third Row Driver Side Seatbelt Sensor: Signal Cross-Coupled | GO to Pinpoint Test AM |
| B140F:11 | Third Row Passenger Side Seatbelt Sensor: Circuit Short To Ground | GO to Pinpoint Test AE |
| B140F:12 | Third Row Passenger Side Seatbelt Sensor: Circuit Short To Battery | GO to Pinpoint Test AE |
| B140F:13 | Third Row Passenger Side Seatbelt Sensor: Circuit Open | GO to Pinpoint Test AE |
| B140F:1D | Third Row Passenger Side Seatbelt Sensor: Circuit Current Out Of Range | GO to Pinpoint Test AE |
| B140F:2B | Third Row Passenger Side Seatbelt Sensor: Signal Cross-Coupled | GO to Pinpoint Test AM |
| B140F:4A | Third Row Passenger Side Seatbelt Sensor: Incorrect Component Installed | GO to Pinpoint Test AN |
| B1410:11 | Second Row Driver Side Seatbelt Pretensioner Deployment Control: Circuit Short To Ground | GO to Pinpoint Test AF |
| B1410:12 | Second Row Driver Side Seatbelt Pretensioner Deployment Control: Circuit Short To Battery | GO to Pinpoint Test AF |
| B1410:13 | Second Row Driver Side Seatbelt Pretensioner Deployment Control: Circuit Open | GO to Pinpoint Test AF |
| B1410:1A | Second Row Driver Side Seatbelt Pretensioner Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test AF |
| B1410:2B | Second Row Driver Side Seatbelt Pretensioner Deployment Control: Signal Cross-Coupled | GO to Pinpoint Test AM |
| B1410:4A | Second Row Driver Side Seatbelt Pretensioner Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AN |
| B1412:11 | Second Row Passenger Side Seatbelt Pretensioner Deployment Control: Circuit Short To Ground | GO to Pinpoint Test AG |
| B1412:12 | Second Row Passenger Side Seatbelt Pretensioner Deployment Control: Circuit Short To Battery | GO to Pinpoint Test AG |
| B1412:13 | Second Row Passenger Side Seatbelt Pretensioner Deployment Control: Circuit Open | GO to Pinpoint Test AG |
| B1412:1A | Second Row Passenger Side Seatbelt Pretensioner Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test AG |
| B1412:2B | Second Row Passenger Side Seatbelt Pretensioner Deployment Control: Signal Cross-Coupled | GO to Pinpoint Test AM |
| B1412:4A | Second Row Passenger Side Seatbelt Pretensioner Deployment Control: Incorrect Component Installed | GO to Pinpoint Test AN |
| B1413:11 | Driver Frontal Restraints Sensor: Circuit Short to Ground | GO to Pinpoint Test AH |
| B1413:12 | Driver Frontal Restraints Sensor: Circuit Short to Battery | GO to Pinpoint Test AH |
| B1413:13 | Driver Frontal Restraints Sensor: Circuit Open | GO to Pinpoint Test AH |
| B1413:4A | Driver Frontal Restraints Sensor: Incorrect Component Installed | GO to Pinpoint Test AN |
| B1413:81 | Driver Frontal Restraints Sensor: Invalid Serial Data Received | GO to Pinpoint Test AI |
| B1413:96 | Driver Frontal Restraints Sensor: Component Internal Failure | GO to Pinpoint Test AI |
| B1414:11 | Driver Side Restraints Sensor 1: Circuit Short to Ground | GO to Pinpoint Test AJ |
| B1414:12 | Driver Side Restraints Sensor 1: Circuit Short to Battery | GO to Pinpoint Test AJ |
| B1414:13 | Driver Side Restraints Sensor 1: Circuit Open | GO to Pinpoint Test AJ |
| B1414:4A | Driver Side Restraints Sensor 1: Incorrect Component Installed | GO to Pinpoint Test AN |
| B1414:81 | Driver Side Restraints Sensor 1: Invalid Serial Data Received | GO to Pinpoint Test AI |
| B1414:96 | Driver Side Restraints Sensor 1: Component Internal Failure | GO to Pinpoint Test AI |
| B1415:11 | Driver Side Restraints Sensor 2: Circuit Short to Ground | GO to Pinpoint Test AK |
| B1415:12 | Driver Side Restraints Sensor 2: Circuit Short to Battery | GO to Pinpoint Test AK |
| B1415:13 | Driver Side Restraints Sensor 2: Circuit Open | GO to Pinpoint Test AK |
| B1415:4A | Driver Side Restraints Sensor 2: Incorrect Component Installed | GO to Pinpoint Test AN |
| B1415:81 | Driver Side Restraints Sensor 2: Invalid Serial Data Received | GO to Pinpoint Test AI |
| B1415:96 | Driver Side Restraints Sensor 2: Component Internal Failure | GO to Pinpoint Test AI |
| B1417:11 | Passenger Frontal Restraints Sensor: Circuit Short To Ground | GO to Pinpoint Test AL |
| B1417:12 | Passenger Frontal Restraints Sensor: Circuit Short To Battery | GO to Pinpoint Test AL |
| B1417:13 | Passenger Frontal Restraints Sensor: Circuit Open | GO to Pinpoint Test AL |
| B1417:4A | Passenger Frontal Restraints Sensor: Incorrect Component Installed | GO to Pinpoint Test AN |
| B1417:81 | Passenger Frontal Restraints Sensor: Invalid Serial Data Received | GO to Pinpoint Test AI |
| B1417:96 | Passenger Frontal Restraints Sensor: Component Internal Failure | GO to Pinpoint Test AI |
| B1418:11 | Passenger Side Restraints Sensor 1: Circuit Short to Ground | GO to Pinpoint Test AK |
| B1418:12 | Passenger Side Restraints Sensor 1: Circuit Short to Battery | GO to Pinpoint Test AK |
| B1418:13 | Passenger Side Restraints Sensor 1: Circuit Open | GO to Pinpoint Test AK |
| B1418:4A | Passenger Side Restraints Sensor 1: Incorrect Component Installed | GO to Pinpoint Test AN |
| B1418:81 | Passenger Side Restraints Sensor 1: Invalid Serial Data Received | GO to Pinpoint Test AI |
| B1418:96 | Passenger Side Restraints Sensor 1: Component Internal Failure | GO to Pinpoint Test AI |
| B1419:11 | Passenger Side Restraints Sensor 2: Circuit Short to Ground | GO to Pinpoint Test AJ |
| B1419:12 | Passenger Side Restraints Sensor 2: Circuit Short to Battery | GO to Pinpoint Test AJ |
| B1419:13 | Passenger Side Restraints Sensor 2: Circuit Open | GO to Pinpoint Test AJ |
| B1419:4A | Passenger Side Restraints Sensor 2: Incorrect Component Installed | GO to Pinpoint Test AN |
| B1419:81 | Passenger Side Restraints Sensor 2: Invalid Serial Data Received | GO to Pinpoint Test AI |
| B1419:96 | Passenger Side Restraints Sensor 2: Component Internal Failure | GO to Pinpoint Test AI |
| B142D:00 | Pyrotechnic End of Life Activation Performed: No Sub Type Information | GO to Pinpoint Test AW |
| B1469:4A | Unused Satellite Restraints Sensor 1: Incorrect Component Installed | GO to Pinpoint Test AN |
| B146A:4A | Unused Satellite Restraints Sensor 2: Incorrect Component Installed | GO to Pinpoint Test AN |
| B1492:68 | Fuel Cutoff Event: Event Information | GO to Pinpoint Test AX |
| B1534:4A | Unused Deployable Device: Incorrect Component Installed | GO to Pinpoint Test AN |
| B1535:4A | Unused DC Sensor Device: Incorrect Component Installed | GO to Pinpoint Test AN |
| C0061:68 | Lateral Acceleration Sensor: Event Information | GO to Pinpoint Test AO |
| C0062:68 | Longitudinal Acceleration Sensor: Event Information | GO to Pinpoint Test AO |
| C0063:68 | Yaw Rate Sensor: Event Information | GO to Pinpoint Test AO |
| C0064:68 | Roll Rate Sensor: Event Information | GO to Pinpoint Test AO |
| C0065:68 | Vertical Acceleration Sensor: Event Information | GO to Pinpoint Test AO |
| U0028:08 | Vehicle Communication Bus A: Bus Signal/Message Failures | GO to Pinpoint Test AP |
| U0028:88 | Vehicle Communication Bus A: Bus Off | GO to Pinpoint Test AP |
| U0100:00 | Lost Communication with ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test AQ |
| U0140:00 | Lost Communication with Body Control Module: No Sub Type Information | GO to Pinpoint Test AR |
| U0146:00 | Lost Communication with Gateway "A": No Sub Type Information | GO to Pinpoint Test AS |
| U0154:00 | Lost Communication with Restraints Occupant Classification System Module: No Sub Type Information | GO to Pinpoint Test AT |
| U0253:00 | Lost Communication with Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test AU |
| U0300:00 | Control Module: No Sub Type Information | GO to Pinpoint Test AW |
| U0401:00 | Invalid Data Received from ECM/PCM A: No Sub Type Information | GO to Pinpoint Test AV |
| U0401:81 | Invalid Data Received from ECM/PCM A: Invalid Serial Data Received | GO to Pinpoint Test AV |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | GO to Pinpoint Test AV |
| U0422:81 | Invalid Data Received From Body Control Module: Invalid Serial Data Received | GO to Pinpoint Test AV |
| U0455:81 | Invalid Data Received From Restraints Occupant Classification System Module: Invalid Serial Data Received | GO to Pinpoint Test AV |
| U0554:00 | Invalid Data Received From Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test AV |
| U0557:82 | Invalid Data Received From Front Controls Interface Module "A": Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test AV |
| U2024:51 | Control Module Cal-Config Data: Not Programmed | GO to Pinpoint Test AY |
| U2024:57 | Control Module Cal-Config Data: Invalid/Incompatible Software Component | GO to Pinpoint Test AW |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test AY |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | GO to Pinpoint Test AP |
| U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | GO to Pinpoint Test AW |
| U2300:55 | Central Configuration: Not Configured | GO to Pinpoint Test AZ |
| U2300:64 | Central Configuration: Signal Plausibility Failure | GO to Pinpoint Test AZ |
| U3000:04 | Control Module: System Internal Failure | GO to Pinpoint Test AW |
| U3000:46 | Control Module: Calibration / Parameter Memory Failure | GO to Pinpoint Test AW |
| U3000:49 | Control Module: Internal Electronic Failure | GO to Pinpoint Test AW |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test BA |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test BA |