| C0051:23 |
Steering Wheel Position Sensor: Signal Stuck Low |
GO to Pinpoint Test Y |
| C0051:27 |
Steering Wheel Position Sensor: Signal Rate Of Change Above Threshold |
GO to Pinpoint Test Y |
| C0051:28 |
Steering Wheel Position Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure |
GO to Pinpoint Test Y |
| C0051:41 |
Steering Wheel Position Sensor: General Checksum Failure |
GO to Pinpoint Test Y |
| C0051:54 |
Steering Wheel Position Sensor: Missing Calibration |
GO to Pinpoint Test Y |
| C0051:62 |
Steering Wheel Position Sensor: Signal Compare Failure |
GO to Pinpoint Test Y |
| C0051:64 |
Steering Wheel Position Sensor: Signal Plausibility Failure |
GO to Pinpoint Test Y |
| C0051:67 |
Steering Wheel Position Sensor: Signal Incorrect After Event |
GO to Pinpoint Test Y |
| C0051:85 |
Steering Wheel Position Sensor: Signal Above Allowable Range |
GO to Pinpoint Test Y |
| C0051:86 |
Steering Wheel Position Sensor: Signal Invalid |
GO to Pinpoint Test Y |
| C006B:00 |
Stability System Active Too Long: No Sub Type Information |
GO to Pinpoint Test Y |
| B1D23:4B |
Overheat Sensor: Over Temperature |
GO to Pinpoint Test AI |
| C102D:00 |
High Friction Inside Power Steering: No Sub Type Information |
GO to Pinpoint Test AA |
| C1110:56 |
Power steering Calibration Data: Invalid/Incompatible Configuration |
GO to Pinpoint Test S |
| C1B00:49 |
Steering Angle Sensor: Internal Electronic Failure |
GO to Pinpoint Test F |
| C1B00:62 |
Steering Angle Sensor: Signal Compare Failure |
GO to Pinpoint Test E |
| C200B:49 |
Steering Shaft Torque Sensor 1: Internal Electronic Failure |
GO to Pinpoint Test N |
| C200B:62 |
Steering Shaft Torque Sensor 1: Signal Compare Failure |
GO to Pinpoint Test J |
| C200C:49 |
Steering Shaft Torque Sensor 2: Internal Electronic Failure |
GO to Pinpoint Test M |
| C200C:62 |
Steering Shaft Torque Sensor 2: Signal Compare Failure |
GO to Pinpoint Test I |
| C200D:49 |
Motor Rotation Angle Sensor: Internal Electronic Failure |
GO to Pinpoint Test P |
| C200D:62 |
Motor Rotation Angle Sensor: Signal Compare Failure |
GO to Pinpoint Test O |
| U0100:00 |
Lost Communication With ECM/PCM 'A': No Sub Type Information |
GO to Pinpoint Test Q |
| U0102:00 |
Lost Communication with Transfer Case Control Module: No Sub Type Information |
GO to Pinpoint Test AP |
| U0121:00 |
Lost Communication With Anti-Lock Brake System (ABS) Control Module 'A': No Sub Type Information |
GO to Pinpoint Test R |
| U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test AB |
| U0155:00 |
Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information |
GO to Pinpoint Test AC |
| U023A:00 |
Lost Communication With Image Processing Module A: No Sub Type Information |
GO to Pinpoint Test AD |
| U023B:00 |
Lost Communication With Image Processing Module B: No Sub Type Information |
GO to Pinpoint Test AD |
| U0401:00 |
Invalid Data Received from ECM/PCM A: No Sub Type Information |
GO to Pinpoint Test AE |
| U0403:00 |
Invalid Data Received From Transfer Case Control Module: No Sub Type Information |
GO to Pinpoint Test AP |
| U0415:00 |
Invalid Data Received from Anti-Lock Brake System (ABS) Control Module 'A': No Sub Type Information |
GO to Pinpoint Test AF |
| U0415:22 |
Invalid Data Received from Anti-Lock Brake System (ABS) Control Module 'A': Signal Amplitude Greater Than Maximum |
GO to Pinpoint Test AF |
| U0422:00 |
Invalid Data Received From Body Control Module: No Sub Type Information |
GO to Pinpoint Test AB |
| U0423:00 |
Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information |
GO to Pinpoint Test AC |
| U053B:00 |
Invalid Data Received From Image Processing Module A: No Sub Type Information |
GO to Pinpoint Test AD |
| U053B:00 |
Invalid Data Received From Image Processing Module A: No Sub Type Information |
GO to Pinpoint Test AG |
| U053C:00 |
Invalid Data Received From Image Processing Module B: No Sub Type Information |
GO to Pinpoint Test AD |
| U2016:47 |
Control Module Main Software: Watchdog/Safety μC Failure |
GO to Pinpoint Test AN |
| U2016:48 |
Control Module Main Software: Supervision Software Failure |
GO to Pinpoint Test AN |
| U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test AO |
| U3000:42 |
Control Module: General Memory Failure |
GO to Pinpoint Test D |
| U3000:49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test D |
| U3000:61 |
Control Module: Signal Calculation Failure |
GO to Pinpoint Test D |
| U3001:68 |
Control Module Improper Shutdown Performance: Event Information |
GO to Pinpoint Test AK |
| U3003:16 |
Battery Voltage: Circuit Voltage Below Threshold |
GO to Pinpoint Test K |
| U3003:17 |
Battery Voltage: Circuit Voltage Above Threshold |
GO to Pinpoint Test K |
| U3003:68 |
Battery Voltage: Event Information |
GO to Pinpoint Test AJ |