System Operation
BCM
The BCM controls various systems by monitoring inputs from switches, sensors and network messages from other modules on the HS-CAN1 and from the GWM. Based on the inputs received, the BCM activates outputs. For example, the BCM monitors the headlamp switch position. Based on this input, the BCM may provide voltage to the exterior lamps.
Battery Saver
The battery saver feature is used to conserve battery voltage. The BCM provides automatic shut-off of the interior lamps after a time-out period when the ignition is off.
Battery Load Shed
The BCM monitors the battery state of charge and when necessary will shut off accessories in order to save the remaining battery charge.
Field Effect Transistor (FET) Protection
The BCM utilizes an Field Effect Transistor (FET) protective circuit strategy for many of its outputs, for example, lamp output circuits. Output loads (current level) are monitored for excessive current (typically short circuits) and are shut down (turns off the voltage or ground provided by the module) when a fault is detected.
A Field Effect Transistor (FET) is a type of transistor that the control module software uses to control and monitor current flow on module outputs. The Field Effect Transistor (FET) protection strategy prevents module damage in the event of excessive current flow.
Output loads (current level) are monitored for excessive current draw (typically short circuits). When a fault event is detected the Field Effect Transistor (FET) turns off and a short circuit DTC sets. The module resets the Field Effect Transistor (FET) protection and allows the circuit to function when the fault is corrected or the ignition state is cycled off and then back on.
When the excessive circuit load occurs often enough, the module shuts down the output until a repair procedure is carried out. Each Field Effect Transistor (FET) protected circuit has three predefined levels of short circuit tolerance based on a module lifetime level of fault events based upon the durability of the Field Effect Transistor (FET). If the total tolerance level is determined to be 600 fault events, the three predefined levels would be 200, 400 and 600 fault events.
When each level is reached, the DTC associated with the short circuit sets along with DTC U1000:00. These Diagnostic Trouble Codes (DTCs) can be cleared using the module on-demand self-test, then the Clear DTC operation on the scan tool (if the on-demand test shows the fault corrected). The module never resets the fault event counter to zero and continues to advance the fault event counter as short circuit fault events occur.
If the number of short circuit fault events reach the third level, then Diagnostic Trouble Codes (DTCs) U1000:00 and U3000:49 set along with the associated short circuit DTC. DTC U3000:49 cannot be cleared and the module must be replaced after the repair.
Post Crash Alert Function
The post crash alert is a function controlled by the BCM. If the RCM determines an impact of enough severity has occurred (the airbags may or may not be deployed), the post crash alert function activates.
The post crash alert function:
- sounds the horn.
- turns on the hazard lights.
- turns on the interior lights.
- unlocks the doors.
The post crash alert function can be turned off by:
- pressing the hazard flasher lamp switch (which may need to be pressed twice).
- pressing the transmitter unlock button.
- pressing the RKE transmitter PANIC button.
- cycling the ignition switch (RUN-OFF-RUN-OFF-RUN).
- opening the driver door.
Power Points
This vehicle is equipped with front and rear 12 volt power points
The power point relays are located in the BJB and are non-serviceable. When the ignition is in the run position the BCM provides a ground for the coil side of the relay, providing 12 volts to the outlets though fuses located in the BJB. For additional information, refer to the Owner's Literature.
Factory-Transport Mode
During vehicle build, some modules (such as the IPC and the BCM) are set to factory mode. When the vehicle build is complete, the vehicle is set to transport mode.
Transport mode is used to reduce the drain on the battery during longer periods when the vehicle is not used. Various system functions can be altered or disabled when in the transport mode. While in transport mode, the IPC displays TRANSPORT MODE in the message center. Transport mode can be disabled and placed into normal operation mode.
Car Configuration Parameters
The parameters are set in the BCM. The parameters are also set in the IPC as backup data for service, in case online As-Built data is not available. For more information, REFER to: Module Configuration