Diagnostic Trouble Code (DTC) Chart
WARNING: This page is about a different car, the 2022 Ford Bronco Sport. However, it is still accessible from the selected car via links, so may be relevant.
Diagnostics in this service information assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
Diagnostic Trouble Code Chart
| Module | DTC | Description | Action |
|---|---|---|---|
| PCM | P2534:00 | Ignition Switch Run/Start Position Circuit Low: No Sub Type Information | For Conventional Ignition Switch: GO to Pinpoint Test D For Push Button Ignition Switch: GO to Pinpoint Test H |
| PCM | P2535:00 | Ignition Switch Run/Start Position Circuit Low: No Sub Type Information | For Conventional Ignition Switch: GO to Pinpoint Test D For Push Button Ignition Switch: GO to Pinpoint Test H |
| BCM | B108A:01 | Start Button: General Electrical Failure | GO to Pinpoint Test H |
| BCM | B108A:24 | Start Button: Signal Stuck High | GO to Pinpoint Test H |
| BCM | B108A:9E | Start Button: Stuck On | GO to Pinpoint Test H |
| BCM | B10F1:14 | Key In Circuit: Circuit Short To Ground or Open | GO to Pinpoint Test G |
| BCM | B1142:29 | Ignition Status 1: Signal Invalid | GO to Pinpoint Test C |
| BCM | B1142:29 | Ignition Status 1: Signal Invalid | GO to Pinpoint Test H |
| BCM | B1240:11 | Start Button Mode Indicator: Circuit Short to Ground | GO to Pinpoint Test I |
| BCM | B1240:15 | Start Button Mode Indicator: Circuit Short to Battery or Open | GO to Pinpoint Test J |
| BCM | B1310:12 | Run/Start Control: Circuit Short to Battery | GO to Pinpoint Test C |
| BCM | B1310:12 | Run/Start Control: Circuit Short to Battery | GO to Pinpoint Test H |
| BCM | B1310:14 | Run/Start Control: Circuit Short to Ground or Open | GO to Pinpoint Test C |
| BCM | B1310:14 | Run/Start Control: Circuit Short to Ground or Open | GO to Pinpoint Test H |
| BCM | B1472:12 | Ignition Key Removal Inhibit: Circuit Short To Battery | GO to Pinpoint Test F |
| BCM | B1472:14 | Ignition Key Removal Inhibit: Circuit Short To Ground or Open | GO to Pinpoint Test F |
| BCM | U300A:01 | Ignition Switch: General Electrical Failure | GO to Pinpoint Test B |
| BCM | U300A:01 | Ignition Switch: General Electrical Failure | GO to Pinpoint Test L |
| SCCM | B112B:04 | Steering Wheel Module: System Internal Failure | GO to Pinpoint Test P |
| SCCM | B112B:44 | Steering Wheel Module: Data Memory Failure | GO to Pinpoint Test P |
| SCCM | B112B:45 | Steering Wheel Module: Program Memory Failure | GO to Pinpoint Test P |
| SCCM | B112B:46 | Steering Wheel Module: Calibration / Parameter Memory Failure | GO to Pinpoint Test P |
| SCCM | B112B:49 | Steering Wheel Module: Internal Electronic Failure | GO to Pinpoint Test P |
| SCCM | B135C:11 | Heater Element: Circuit Short To Ground | GO to Pinpoint Test O |
| SCCM | B135C:13 | Heater Element: Circuit Open | GO to Pinpoint Test O |
| SCCM | U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test Q |
| SCCM | U0146:00 | Lost Communication With Gateway "A": No Sub Type Information | GO to Pinpoint Test Q |
| SCCM | U0155:00 | Lost Communication With Instrument Panel Cluster Module: No Sub Type Information | GO to Pinpoint Test Q |
| SCCM | U023A:00 | Lost Communication With Image Processing Module "A": No Sub Type Information | GO to Pinpoint Test Q |
| SCCM | U210A:11 | Temperature Sensor: Circuit Short To Ground | GO to Pinpoint Test O |
| SCCM | U210A:13 | Temperature Sensor: Circuit Open | GO to Pinpoint Test O |
| SCCM | U210A:29 | Temperature Sensor: Signal Invalid | GO to Pinpoint Test O |
| SCCM | U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | GO to Pinpoint Test P |
| SCCM | U3003:A2 | Battery Voltage: System Voltage Low | GO to Pinpoint Test M |
| SCCM | U3003:A3 | Battery Voltage: System Voltage High | GO to Pinpoint Test N |