| C0051:23 |
Steering Wheel Position Sensor: Signal Stuck Low |
GO to Pinpoint Test AG |
| C0051:27 |
Steering Wheel Position Sensor: Signal Rate Of Change Above Threshold |
GO to Pinpoint Test AG |
| C0051:28 |
Steering Wheel Position Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure |
GO to Pinpoint Test AG |
| C0051:41 |
Steering Wheel Position Sensor: General Checksum Failure |
GO to Pinpoint Test AG |
| C0051:54 |
Steering Wheel Position Sensor: Missing Calibration |
GO to Pinpoint Test AG |
| C0051:62 |
Steering Wheel Position Sensor: Signal Compare Failure |
GO to Pinpoint Test AG |
| C0051:64 |
Steering Wheel Position Sensor: Signal Plausibility Failure |
GO to Pinpoint Test AG |
| C0051:67 |
Steering Wheel Position Sensor: Signal Incorrect After Event |
GO to Pinpoint Test AG |
| C0051:85 |
Steering Wheel Position Sensor: Signal Above Allowable Range |
GO to Pinpoint Test AG |
| C0051:86 |
Steering Wheel Position Sensor: Signal Invalid |
GO to Pinpoint Test AG |
| C006B:00 |
Stability System Active Too Long: No Sub Type Information |
GO to Pinpoint Test AG |
| B1D23:4B |
Overheat Sensor: Over Temperature |
GO to Pinpoint Test BB |
| C102D:00 |
High Friction Inside Power Steering: No Sub Type Information |
GO to Pinpoint Test AI |
| C1110:56 |
Power steering Calibration Data: Invalid/Incompatible Configuration |
GO to Pinpoint Test AA |
| C1B00:49 |
Steering Angle Sensor: Internal Electronic Failure |
GO to Pinpoint Test BF |
| C1B00:62 |
Steering Angle Sensor: Signal Compare Failure |
GO to Pinpoint Test BF |
| C200B:49 |
Steering Shaft Torque Sensor 1: Internal Electronic Failure |
GO to Pinpoint Test BG |
| C200B:62 |
Steering Shaft Torque Sensor 1: Signal Compare Failure |
GO to Pinpoint Test BG |
| C200C:49 |
Steering Shaft Torque Sensor 2: Internal Electronic Failure |
GO to Pinpoint Test BH |
| C200C:62 |
Steering Shaft Torque Sensor 2: Signal Compare Failure |
GO to Pinpoint Test BH |
| C200D:49 |
Motor Rotation Angle Sensor: Internal Electronic Failure |
GO to Pinpoint Test BI |
| C200D:62 |
Motor Rotation Angle Sensor: Signal Compare Failure |
GO to Pinpoint Test BI |
| P0635:68 |
Power Steering Control Circuit: Event Information |
GO to Pinpoint Test D |
| U0100:00 |
Lost Communication With ECM/PCM "A": No Sub Type Information |
GO to Pinpoint Test AJ |
| U0121:00 |
Lost Communication With Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information |
GO to Pinpoint Test AK |
| U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test AL |
| U0146:00 |
Lost Communication With Serial Data Gateway "A": No Sub Type Information |
GO to Pinpoint Test AM |
| U0151:00 |
Lost Communication With Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test AN |
| U0159:00 |
Lost Communication With Parking Assist Control Module "A": No Sub Type Information |
GO to Pinpoint Test AP |
| U023A:00 |
Lost Communication With Image Processing Module A: No Sub Type Information |
GO to Pinpoint Test AR |
| U0415:00 |
Invalid Data Received from Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information |
GO to Pinpoint Test AT |
| U0422:00 |
Invalid Data Received From Body Control Module: No Sub Type Information |
GO to Pinpoint Test BU |
| U0452:00 |
Invalid Data Received From Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test BX |
| U053B:00 |
Invalid Data Received From Image Processing Module A: No Sub Type Information |
GO to Pinpoint Test AX |
| U2014:68 |
Control Module Hardware: Event Information |
GO to Pinpoint Test E |
| U2016:47 |
Control Module Main Software: Watchdog/Safety μC Failure |
GO to Pinpoint Test BO |
| U2016:48 |
Control Module Main Software: Supervision Software Failure |
GO to Pinpoint Test BO |
| U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test BQ |
| U3000:42 |
Control Module: General Memory Failure |
GO to Pinpoint Test B |
| U3000:49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test B |
| U3000:96 |
Control Module: Component Internal Failure |
GO to Pinpoint Test B |
| U3001:68 |
Control Module Improper Shutdown Performance: Event Information |
GO to Pinpoint Test BD |
| U3003:16 |
Battery Voltage: Circuit Voltage Below Threshold |
GO to Pinpoint Test BC |
| U3003:17 |
Battery Voltage: Circuit Voltage Above Threshold |
GO to Pinpoint Test BC |
| U3003:19 |
Battery Voltage: Circuit Current Above Threshold |
GO to Pinpoint Test BC |
| U3003:68 |
Battery Voltage: Event Information |
GO to Pinpoint Test BC |
| U3003:A2 |
Battery Voltage: System Voltage Low |
GO to Pinpoint Test BC |