| B11D9:16 |
Vehicle Battery: Circuit Voltage Below Threshold |
GO to Pinpoint Test A |
| B11D9:17 |
Vehicle Battery: Circuit Voltage Above Threshold |
GO to Pinpoint Test A |
| U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test B |
| U2002:9E |
Switch: Stuck On |
GO to Pinpoint Test C |
| U2009:9E |
Rotary Encoder: Stuck On |
GO to Pinpoint Test D |
| U3000:04 |
Control Module: System Internal Failures |
GO to Pinpoint Test D |
| C00A1:57 |
Driveline Control Module: Invalid/Incompatible Software Component |
GO to Pinpoint Test E |
| C00A1:F1 |
Driveline Control Module: Ethernet 2 Failure |
GO to Pinpoint Test E |
| C00A5:01 |
Driveline Control Module Transfer Case Unit Control Circuit Driver: General Electrical Failure |
GO to Pinpoint Test E |
| C00A5:08 |
Driveline Control Module Transfer Case Unit Control Circuit Driver: Bus Signal/Message Failures |
GO to Pinpoint Test E |
| C00A5:19 |
Driveline Control Module Transfer Case Unit Control Circuit Driver: Circuit Current Above Threshold |
GO to Pinpoint Test E |
| C00A5:1C |
Driveline Control Module Transfer Case Unit Control Circuit Driver: Circuit Voltage Out Of Range |
GO to Pinpoint Test E |
| C00A5:49 |
Driveline Control Module Transfer Case Unit Control Circuit Driver: Internal Electronic Failure |
GO to Pinpoint Test E |
| C00A5:4B |
Driveline Control Module Transfer Case Unit Control Circuit Driver: Over Temperature |
GO to Pinpoint Test E |
| C00A5:96 |
Driveline Control Module Transfer Case Unit Control Circuit Driver: Component Internal Failure |
GO to Pinpoint Test E |
| C00A6:18 |
4WD/AWD Transfer Case Unit Actuator: Circuit Current Below Threshold |
GO to Pinpoint Test F |
| C00A6:19 |
4WD/AWD Transfer Case Unit Actuator: Circuit Current Above Threshold |
GO to Pinpoint Test F |
| C00A6:4B |
4WD/AWD Transfer Case Unit Actuator: Over Temperature |
GO to Pinpoint Test G |
| C00A6:54 |
4WD/AWD Transfer Case Unit Actuator: Missing Calibration |
GO to Pinpoint Test H |
| C00A6:66 |
4WD/AWD Transfer Case Unit Actuator: Signal Has Too Many Transitions/Events |
GO to Pinpoint Test I |
| C00A6:71 |
4WD/AWD Transfer Case Unit Actuator: Actuator Stuck |
GO to Pinpoint Test F |
| C00A6:74 |
4WD/AWD Transfer Case Unit Actuator: Actuator Slipping |
GO to Pinpoint Test F |
| C00A6:99 |
4WD/AWD Transfer Case Unit Actuator: Exceeded Learning Limit |
GO to Pinpoint Test F |
| C00A7:11 |
4WD/AWD Transfer Case Unit Actuator Position Sensor "A": Circuit Short To Ground |
GO to Pinpoint Test J |
| C00A7:13 |
4WD/AWD Transfer Case Unit Actuator Position Sensor "A": Circuit Open |
GO to Pinpoint Test J |
| C00A7:17 |
4WD/AWD Transfer Case Unit Actuator Position Sensor "A": Circuit Voltage Above Threshold |
GO to Pinpoint Test J |
| C00A8:11 |
4WD/AWD Transfer Case Unit Actuator Position Sensor "B": Circuit Short To Ground |
GO to Pinpoint Test K |
| C00A8:13 |
4WD/AWD Transfer Case Unit Actuator Position Sensor "B": Circuit Open |
GO to Pinpoint Test K |
| C00A8:17 |
4WD/AWD Transfer Case Unit Actuator Position Sensor "B": Circuit Voltage Above Threshold |
GO to Pinpoint Test K |
| P0562:00 |
System Voltage Low: No Sub Type Information |
GO to Pinpoint Test E |
| P0563:00 |
System Voltage High: No Sub Type Information |
GO to Pinpoint Test E |
| P0603:00 |
Internal Control Module Keep Alive Memory (KAM) Error: No Sub Type Information |
GO to Pinpoint Test E |
| P0604:00 |
Internal Control Module Random Access Memory (RAM) Error: No Sub Type Information |
GO to Pinpoint Test E |
| P0605:00 |
Internal Control Module Read Only Memory (ROM) Error: No Sub Type Information |
GO to Pinpoint Test E |
| P0607:00 |
Control Module Performance: No Sub Type Information |
GO to Pinpoint Test E |
| P060A:00 |
Internal Control Module Monitoring Processor Performance: No Sub Type Information |
GO to Pinpoint Test E |
| P060B:00 |
Internal Control Module A/D Processing Performance: No Sub Type Information |
GO to Pinpoint Test E |
| P060C:00 |
Internal Control Module Main Processor Performance: No Sub Type Information |
GO to Pinpoint Test E |
| P0630:00 |
VIN Not Programmed or Incompatible - ECM/PCM: No Sub Type Information |
GO to Pinpoint Test L |
| P064F:00 |
Unauthorized Software/Calibration Detected: No Sub Type Information |
GO to Pinpoint Test E |
| P068A:00 |
ECM/PCM Power Relay De-Energized - Too Early: No Sub Type Information |
GO to Pinpoint Test E |
| P1001:00 |
KOER Not Able to Complete, KOER Aborted: No Sub Type Information |
GO to Pinpoint Test M |
| P1397:01 |
System Voltage Out Of Self Test Range: General Electrical Failure |
GO to Pinpoint Test M |
| P1501:00 |
Vehicle Speed Sensor Out Of Self Test Range: No Sub Type Information |
GO to Pinpoint Test M |
| P160A:00 |
Control Module Vehicle Options Reconfiguration Error: No Sub Type Information |
GO to Pinpoint Test L |
| P166E:00 |
Internal Control Module All Wheel Drive Disconnect Control Performance: No Sub Type Information |
GO to Pinpoint Test N |
| P1674:00 |
Control Module Software Corrupted: No Sub Type Information |
GO to Pinpoint Test E |
| P1705:00 |
Transmission Range Circuit Not Indicating Park/Neutral During Self Test: No Sub Type Information |
GO to Pinpoint Test M |
| U0100:00 |
Lost Communication With ECM/PCM "A": No Sub Type Information |
GO to Pinpoint Test O |
| U0101:00 |
Lost Communication with TCM: No Sub Type Information |
GO to Pinpoint Test O |
| U0121:00 |
Lost Communication With Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information |
GO to Pinpoint Test O |
| U0126:00 |
Lost Communication With Steering Angle Sensor Module: No Sub Type Information |
GO to Pinpoint Test O |
| U0137:00 |
Lost Communication With Trailer Brake Control Module: No Sub Type Information |
GO to Pinpoint Test O |
| U0138:00 |
Lost Communication with All Terrain Control Module: No Sub Type Information |
GO to Pinpoint Test O |
| U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test O |
| U0146:00 |
Lost Communication With Serial Data Gateway "A": No Sub Type Information |
GO to Pinpoint Test O |
| U0151:00 |
Lost Communication With Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test O |
| U0155:00 |
Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information |
GO to Pinpoint Test O |
| U0164:00 |
Lost Communication With HVAC Control Module: No Sub Type Information |
GO to Pinpoint Test O |
| U0212:00 |
Lost Communication With Steering Column Control Module: No Sub Type Information |
GO to Pinpoint Test O |
| U0402:00 |
Invalid Data Received from TCM: No Sub Type Information |
GO to Pinpoint Test P |
| U0415:00 |
Invalid Data Received from Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information |
GO to Pinpoint Test P |
| U0422:00 |
Invalid Data Received From Body Control Module: No Sub Type Information |
GO to Pinpoint Test P |
| U0423:00 |
Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information |
GO to Pinpoint Test P |
| U0428:00 |
Invalid Data Received From Steering Angle Sensor Module: No Sub Type Information |
GO to Pinpoint Test P |
| U1012:00 |
Invalid Internal Control Module Monitoring Data Received from Anti-Lock Brake System (ABS) Control Module: No Sub Type Information |
GO to Pinpoint Test P |
| U1014:00 |
Invalid Internal Control Module Monitoring Data Received from Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test P |
| U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test L |
| U2101:00 |
Control Module Configuration Incompatible: No Sub Type Information |
GO to Pinpoint Test L |
| U2200:00 |
Control Module Configuration Memory Corrupt: No Sub Type Information |
GO to Pinpoint Test L |