Diagnostic Trouble Code (DTC) Chart
Diagnostics in this service information assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
| Module | DTC | Description | Action |
|---|---|---|---|
| PCM | P0521:00 | Engine Oil Pressure Sensor/Switch 'A' Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test J |
| PCM | P0524:00 | Engine Oil Pressure Too Low: No Sub Type Information | GO to Pinpoint Test J |
| PCM | P0602:00 | Powertrain Control Module Programming Error: No Sub Type Information | GO to Pinpoint Test QA |
| PCM | P0604:00 | Internal Control Module Random Access Memory (RAM) Error: No Sub Type Information | GO to Pinpoint Test QA |
| PCM | P0605:00 | Internal Control Module Read Only Memory (ROM) Error: No Sub Type Information | GO to Pinpoint Test QA |
| PCM | P0606:00 | Control Module Processor: No Sub Type Information | GO to Pinpoint Test QA |
| PCM | P0607:00 | Control Module Performance: No Sub Type Information | GO to Pinpoint Test QA |
| PCM | P0610:00 | Control Module Vehicle Options Error: No Sub Type Information | GO to Pinpoint Test QA |
| PCM | P061E:00 | Internal Control Module Brake Signal Performance: No Sub Type Information | GO to Pinpoint Test QA |
| PCM | P062F:00 | Internal Control Module EEPROM Error: No Sub Type Information | GO to Pinpoint Test QA |
| PCM | P0630:00 | VIN Not Programmed or Incompatible - ECM/PCM: No Sub Type Information | GO to Pinpoint Test QA |
| PCM | P064F:00 | Unauthorized Software/Calibration Detected: No Sub Type Information | GO to Pinpoint Test QA |
| PCM | P06DA:00 | Engine Oil Pressure Control Circuit/Open: No Sub Type Information | GO to Pinpoint Test K |
| PCM | P06DB:00 | Engine Oil Pressure Control Circuit Low: No Sub Type Information | GO to Pinpoint Test K |
| PCM | P06DC:00 | Engine Oil Pressure Control Circuit High: No Sub Type Information | GO to Pinpoint Test K |
| PCM | P06DD:00 | Engine Oil Pressure Control Circuit Performance/Stuck Off: No Sub Type Information | GO to Pinpoint Test J |
| PCM | P06DE:00 | Engine Oil Pressure Control Circuit Stuck On: No Sub Type Information | GO to Pinpoint Test J |
| PCM | P1001:00 | KOER Not Able to Complete, KOER Aborted: No Sub Type Information | GO to Pinpoint Test QC |
| PCM | P160A:00 | Control Module Vehicle Options Reconfiguration Error: No Sub Type Information | GO to Pinpoint Test QA |
| PCM | P161C:00 | Automatic Engine Shutdown Mismatch with Vehicle Configuration: No Sub Type Information | GO to Pinpoint Test QA |
| PCM | P1635:00 | Tire/Axle Out of Acceptable Range: No Sub Type Information | GO to Pinpoint Test QA |
| PCM | P1639:00 | Vehicle ID Block Corrupted, Not Programmed: No Sub Type Information | GO to Pinpoint Test QA |
| PCM | P1935:00 | Brake Switch/Sensor Signal: No Sub Type Information | GO to Pinpoint Test QA |
| PCM | P264F:00 | Engine Serial Number Not Programmed or Incompatible: No Sub Type Information | GO to Pinpoint Test QA |
| PCM | P26C5:00 | Exhaust Flow Control Valve 'A' Control Circuit/Open: No Sub Type Information | GO to Pinpoint Test L |
| PCM | P26C6:00 | Exhaust Flow Control Valve 'A' Control Circuit Low: No Sub Type Information | GO to Pinpoint Test L |
| PCM | P26C7:00 | Exhaust Flow Control Valve 'A' Control Circuit High: No Sub Type Information | GO to Pinpoint Test L |
| PCM | P26FE:00 | Exhaust Flow Control Valve 'A' Control Performance: No Sub Type Information | GO to Pinpoint Test L |
| PCM | P2B57:00 | Low Engine Oil Pressure - Camshaft Control Disabled: No Sub Type Information | GO to Pinpoint Test J |
| PCM | P2BF5:00 | Exhaust Flow Control Valve 'A' Position Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test L |
| PCM | P2BF8:00 | Exhaust Flow Control Valve 'B' Control Circuit/Open: No Sub Type Information | GO to Pinpoint Test M |
| PCM | P2BF9:00 | Exhaust Flow Control Valve 'B' Control Circuit Low: No Sub Type Information | GO to Pinpoint Test M |
| PCM | P2BFA:00 | Exhaust Flow Control Valve 'B' Control Circuit High: No Sub Type Information | GO to Pinpoint Test M |
| PCM | P2BFB:00 | Exhaust Flow Control Valve 'B' Control Performance: No Sub Type Information | GO to Pinpoint Test M |
| PCM | P2BFD:00 | Exhaust Flow Control Valve 'B' Position Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test M |
| PCM | U0104:00 | Lost Communication With Cruise Control Module: No Sub Type Information | GO to Pinpoint Test A |
| PCM | U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module 'A': No Sub Type Information | GO to Pinpoint Test B |
| PCM | U0126:00 | Lost Communication With Steering Angle Sensor Module: No Sub Type Information | GO to Pinpoint Test C |
| PCM | U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test D |
| PCM | U0164:00 | Lost Communication With HVAC Control Module 'A': No Sub Type Information | GO to Pinpoint Test E |
| PCM | U0212:00 | Lost Communication With Steering Column Control Module: No Sub Type Information | GO to Pinpoint Test C |
| PCM | U023A:00 | Lost Communication With Image Processing Module A: No Sub Type Information | GO to Pinpoint Test F |
| PCM | U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test G |
| PCM | U0405:00 | Invalid Data Received From Cruise Control Module: No Sub Type Information | GO to Pinpoint Test I |
| PCM | U0415:00 | Invalid Data Received from Anti-Lock Brake System (ABS) Control Module 'A': No Sub Type Information | GO to Pinpoint Test I |
| PCM | U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | GO to Pinpoint Test I |
| PCM | U0423:00 | Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information | GO to Pinpoint Test I |
| PCM | U0554:00 | Invalid Data Received From Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test I |
| PCM | U1012:00 | Invalid Internal Control Module Monitoring Data Received from Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | GO to Pinpoint Test I |
| PCM | U1022:00 | Invalid Internal Control Module Monitoring Data Received from Body Control Module: No Sub Type Information | GO to Pinpoint Test I |
| PCM | U1039:00 | Data Storage 2: No Sub Type Information | GO to Pinpoint Test QA |
| PCM | U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test QA |
| PCM | U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | GO to Pinpoint Test QA |
| PCM | U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | GO to Pinpoint Test QA |
| PCM | U3003:00 | Battery Voltage: No Sub Type Information | GO to Pinpoint Test H |