Common Specifications & Procedures

RANGER COMMON SPECIFICATIONS & PROCEDURES

System		Specification/Procedure
Air Conditioning
Service		SPECIFICATIONS
Torque:		Refer to the appropriate component in REMOVAL AND INSTALLATION
Axle Nut/Hub Nut		175 Nm (129 lb - ft)
Battery		SPECIFICATIONS
Brakes
Bleeding Sequence		Brake System Pressure Bleeding - Vehicles With: Electric Brake Booster or Brake System Pressure Bleeding - Vehicles With: Vacuum Brake Booster
Front Disc Brakes w/Torque		Refer to appropriate component in REMOVAL AND INSTALLATION 150 Nm (110 lb - ft)
Rear Disc Brakes w/Torque		Refer to appropriate component in REMOVAL AND INSTALLATION 150 Nm (110 lb - ft)
Charging
Generator w/Torque
	2.3L EcoBoost (201kW/273PS)	For removal and installation, refer to REMOVAL AND INSTALLATION Upper Generator Bolt And Bracket: 22 lb.ft (30 Nm) Lower Generator Bolt: 18 lb.ft (25 Nm) Generator Nut: 12.9 lb.ft (17.5 Nm)
Drive Belts
Adjustment		Accessory Drive Belt
Belt Routing		Accessory Drive - Component Location .
Engine Cooling
General Service Specifications		2.3L EcoBoost (201kW/273PS) SPECIFICATIONS
Pressure Relief Cap Pressure		135 kPa to 155 kPa (19.5 psi to 22.4 psi)
Thermostat Removal & Installation		Thermostat .
Water Pump R & I		Coolant Pump
Engine Cooling
General Service Specifications		2.7L EcoBoost (238kW 324PS) SPECIFICATIONS
Degas Bottle Cap		120 kPa to 150 kPa (17.4 psi to 21.7 psi)
Thermostat Removal & Installation		THERMOSTAT .
Water Pump Removal & Installation		COOLANT PUMP
Engine Cooling
General Service Specifications		3.0L EcoBoost (299kW 406PS) (DD) SPECIFICATIONS
Pressure Relief Cap Pressure		145 kPa (21 psi)
Thermostat Removal & Installation		THERMOSTAT .
Water Pump Removal & Installation		COOLANT PUMP
Engine Mechanical
2.3L Ecoboost / 2.7L Ecoboost Compression		10.0:1 SPECIFICATIONS
3.0L Ecoboost Compression		10.5:1 SPECIFICATIONS
2.3L Ecoboost (201Kw/273Ps) Oil pressure @ 1, 500 rpm with engine oil temperature between 121.9 - 175.9 °F (50 - 80 °C)		27.6 - 37.7 psi (190 - 260 kPa)
2.7L Ecoboost (238Kw/324Ps) Oil pressure @ 1, 500 rpm with engine oil temperature between 121.9 - 175.9 °F (50 - 80 °C)		15.9 - 24.6 psi (110 - 170 kPa)
3.0L Ecoboost (299Kw/406Ps) (DD) Oil pressure @ 1, 500 rpm with engine oil temperature between 121.9 - 175.9 °F (50 - 80 °C)		15.9 - 24.6 psi (110 - 170 kPa)
Overhaul		SPECIFICATIONS
	Torque:	Refer to appropriate component in REMOVAL AND INSTALLATION
Fluid Specifications		See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button.
Flywheel/Flex Plate Torque
2.3L EcoBoost (201kW/273PS)		For tightening sequence, refer to Flexplate . Stage 1: 37 lb.ft (50 Nm) Stage 2: 59 lb.ft (80 Nm) Stage 3: 83 lb.ft (112 Nm)
2.7L Ecoboost (238Kw/324Ps) / 3.0L Ecoboost (299Kw/406Ps) (DD)		For tightening sequence, refer to Flexplate . Stage 1: 59 lb.ft (80 Nm)
Fuel System
Fuel Filter Location		The system contains 3 to 5 filtering or screening devices. The fuel intake filter or screen is a fine nylon mesh filter mounted on the intake side of the fuel pump. It is part of the assembly and cannot be repaired separately. The filter/screen at the fuel rail port of the injectors is part of the fuel injector assembly and cannot be repaired separately The filter/screen at fuel inlet side of the fuel pressure regulator is part of the regulator assembly and cannot be repaired separately. The fuel filter assembly is located between the fuel pump and injectors. This filter may be a lifetime fuel filter located in the fuel pump assembly or an external 3 port inline filter that allows clean fuel to return to the fuel tank. A new filter may be installed for the external filter. The fuel filter sock is located on the fuel pump assembly between the reservoir and the fuel tank. The fuel filter sock is located on the fuel pump assembly between the reservoir and the fuel tank.
Fuel Filter R & I		Fuel Pump and Sender Unit Fuel Injectors
Pressure Release Procedure		Fuel System Pressure Release
Fuel Pressure Test Procedure		Fuel System Pressure Check
Ignition
Firing Order & Cylinder Identification		2.3L EcoBoost 1-3-4-2 2.7L / 3.0L EcoBoost 1-4-2-5-3-6 Refer to: FIRING ORDER & CYLINDER IDENTIFICATION
Ignition Wires (Routing)		Engine has coil-on-plug ignition.
Spark Plug
2.3L EcoBoost (201kW/273PS)
	Type	CYFS 12Y RT3
Gap		2.3L EcoBoost - 0.030 in (.75 mm) 2.7L / 3.0L EcoBoost - 0.028-0.031 in (0.7-0.8 mm)
Torque:		2.3L EcoBoost - 106 lb.in (12 Nm) 2.7L / 3.0L EcoBoost - 132 lb.in (15 Nm)
Starting
Starter		SPECIFICATIONS
Torque:
	For removal and installation, refer to Starter Motor .	Starter Motor Studbolts: 35 lb.ft (48 Nm)
Wheel Alignment
Adjustment Specifications		SPECIFICATIONS
Torque:		Refer to the appropriate procedure in GENERAL PROCEDURES
Wheel & Tire
Wheel Lug Nut Torque		For tightening sequence, refer to Wheel and Tire . 135 Nm