Common Specs & Procedures
ACCORD COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | A/C SYSTEM SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Axle Nut/Hub Nut | 181 Ft. Lbs. (245 N.m) | ||
| Battery | |||
| 2.2L | CAPACITIES | ||
| 2.7L | CAPACITIES | ||
| Brakes | |||
| Bleeding Sequence | |||
| With ABS | BLEEDING BRAKE SYSTEM | ||
| Without ABS | BLEEDING BRAKE SYSTEM | ||
| Disc Brakes | |||
| Service Specifications | DISC BRAKE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Drum Brakes | |||
| Service Specifications | DRUM BRAKE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Charging | |||
| Generator | Refer to GENERATOR OUTPUT SPECIFICATIONS table located under DESCRIPTION | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | BELT INSPECTION & ADJUSTMENT | ||
| Drive Belt Routing | DRIVE BELT ROUTING | ||
| Engine Cooling | |||
| General Service Specifications | COOLING SYSTEM SPECIFICATIONS | ||
| Radiator Cap Pressure | 14-18 psi | ||
| Thermostat R & I | |||
| 2.2L 4-CYL | THERMOSTAT | ||
| 2.7L V6 | THERMOSTAT | ||
| Water Pump R & I | |||
| 2.2L 4-CYL | WATER PUMP | ||
| 2.7L V6 | WATER PUMP | ||
| Engine Mechanical | |||
| 2.2L 4-CYL | |||
| Compression | ENGINE COMPRESSION | ||
| Oil Pressure | Measure oil pressure with engine temperature at 176°F (80°C). At idle, minimum oil pressure should be 10 psi (0.7 kg/cm2 ). At 3000 RPM, oil pressure should be 50 psi (3.5 kg/cm2 ). (Except H22A4 Engine With M/T & ATTS) Measure oil pressure with engine temperature at 176°F (80°C). At idle, minimum oil pressure should be 10 psi (0.7 kg/cm2 ). At 3000 RPM, oil pressure should be 50 psi (3.5 kg/cm2 ). (H22A4 Engine With M/T & ATTS) | ||
| Overhaul | ENGINE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| 2.7L V6 | |||
| Compression | ENGINE COMPRESSION | ||
| Oil Pressure | With oil temperature at 176°F (80°C), oil pressure should be 12 psi (78 kPa) minimum at idle, and 63 psi (430 kPa) minimum at 3000 RPM. | ||
| Overhaul | ENGINE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | |||
| 2.2L 4-CYL | 76 Ft. Lbs. (103 N.m) | ||
| 2.7L V6 | 54 Ft. Lbs. (73 N.m) | ||
| Fuel System | |||
| 2.2L | |||
| Pressure Specification | FUEL PUMP | ||
| Fuel Pressure Test Procedure | PRESSURE TESTING | ||
| Fuel Filter Location | FUEL FILTER | ||
| Fuel Filter R & I | FUEL FILTER | ||
| 2.7L | |||
| Pressure Specification | FUEL PUMP | ||
| Fuel Pressure Test Procedure | FUEL SYSTEM PRESSURE RELEASE | ||
| Fuel Filter Location | FUEL FILTER | ||
| Fuel Filter R & I | FUEL FILTER | ||
| Ignition | |||
| 2.2L | |||
| Firing Order & Cylinder Identification | FIRING ORDER & TIMING MARKS | ||
| Ignition Wires (Resistance) | HIGH TENSION WIRE RESISTANCE | ||
| Ignition Wires (Routing) | FIRING ORDER & TIMING MARKS | ||
| 2.7L | |||
| Firing Order & Cylinder Identification | FIRING ORDER & TIMING MARKS | ||
| Ignition Wires (Resistance) | HIGH TENSION WIRE RESISTANCE | ||
| Ignition Wires (Routing) | FIRING ORDER & TIMING MARKS | ||
| Spark Plug | |||
| 2.2L 4-CYL | SPARK PLUGS | ||
| 2.7L V6 | SPARK PLUGS | ||
| Starting | |||
| Starter | STARTER SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT PROCEDURES | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 80 Ft. Lbs. (108 N.m) | ||