LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Honda >> 2000 >> Odyssey Cargo >> Repair and Diagnosis >> External Pages >> Different car >> Section 73 (Multiplex Integrated Control System) >> DTC Troubleshooting >> DTC B1000: Communication Bus Line Error
April 5, 2026: LEMON Manuals is launched! Read the announcement.

DTC B1000: Communication Bus Line Error

WARNING: This page is about a different car, the 2006 Honda Odyssey and 2005 Honda Odyssey. However, it is still accessible from the selected car via links, so may be relevant.
  1. Clear the DTCs with the HDS.
  2. Turn the ignition switch OFF, and then back ON (II).
  3. Wait for 6 seconds or more.
  4. Check for DTCs with the HDS.

    Is DTC B1000 indicated? 

    1. YES  - Go to step 5.
    2. NO  - Intermittent failure. The communication bus line is OK at this time. Check for loose or poor connections, or worn/shorted wires. If the connections are good, check the battery condition (see BATTERY TEST ) and the charging system.
  5. Check for DTCs with the HDS.

    Are DTCs B1005, B1006, B1007, B1008, and B1012 indicated? 

    1. YES  - Go to step 6.
    2. NO  - Replace the MICU.
  6. Disconnect the appropriate connector at each control unit in the table one at a time. Clear the DTC, then recheck for DTCs after each unit is disconnected.
    CONTROL UNIT SPECIFICATION

    Control Unit Connector
    Gauge Control Module Connector A (30P)
    Relay Control Module Connector K (10P)
    Door Multiplex Control Unit Power window master switch connector (23P)
    Combination Switch Control Unit Connector (8P)
    Automatic Lighting Control Unit Connector (14P)
    MICU-Rear Junction Box Connector A (14P)
    A/C Control Panel Connector (22P)
    Climate Control Unit Connector (30P)

    Is DTC B1000 indicated with each individual unit disconnected? 

    1. YES  - Go to step  10.
    2. NO  - Replace the control unit that was disconnected when B1000 did not reset. (If the unit is the MICU-rear junction box control unit, go to step 7 )
  7. Disconnect connector D (17P) and connector G (8P) from the MICU-rear junction box.
  8. Check for continuity between each of the MICU-rear junction box terminals listed in the table shown in CONNECTED CONTROL UNIT SPECIFICATION , and body ground.
    CONNECTED CONTROL UNIT SPECIFICATION

    Connected control unit MICU-rear junction box terminal
    Power Seat Control Unit D8
    Right Power Sliding Door Control Unit D9
    Left Power Sliding Door Control Unit/Power Tailgate Control Unit G4

    Is there continuity? 

    1. YES  - Repair a short in the wire between the MICU-rear junction box to ground and the affected control unit.
    2. NO  - Go to step 9.
  9. Check for voltage between each of the MICU-rear junction box terminals listed in the table shown in CONNECTED CONTROL UNIT SPECIFICATION , and body ground.
    CONNECTED CONTROL UNIT SPECIFICATION

    Connected control unit MICU-Rear junction box terminal
    Power Seat Control Unit D8
    Right Power Sliding Door Control Unit D9
    Left Power Sliding Door Control Unit/Power Tailgate Control Unit G4

    Is there less than 1 V ? 

    1. YES  - Replace the MICU-rear junction box.
    2. NO  - Repair an open in the wire between the MICU-rear junction box and the connected control units.
  10. Disconnect all of the appropriate connectors for each of the units in the table shown in CONTROL UNIT SPECIFICATION .
    CONTROL UNIT SPECIFICATION

    Control Unit Connector
    Gauge Control Module Connector A (30P)
    Relay Control Module Connector K (10P)
    Door Multiplex Control Unit Power window master switch connector (23P)
    Combination Switch Control Unit Connector (8P)
    Automatic Lighting Control Unit Connector (14P)
    MICU-Rear Junction Box Connector A (14P)
    A/C Control Panel Connector (22P)
    Climate Control Unit Connector (30P)
  11. Disconnect driver's under-dash fuse/relay box connectors D (17P), G (8P), J (30P), N (45P), X (39P), and P (30P).
  12. Check for continuity between each of the driver's under-dash fuse/relay box terminals listed in the table shown in CONNECTED CONTROL UNIT SPECIFICATION , and body ground.
    CONNECTED CONTROL UNIT SPECIFICATION

    Connected Control Unit Driver's under-dash fuse/relay box terminal
    Gauge Control Module N28
    Relay Control Module D11
    Door Multiplex Control Unit J4
    Combination Switch Control Unit X27
    Automatic Lighting Control Unit X18
    MICU-Rear Junction Box G1
    A/C Control Panel/Climate Control Unit N22

    Is there continuity? 

    1. YES  - Repair a short in the wire between the driver's under-dash fuse/relay box and the affected control unit.
    2. NO  - Go to step 13.
  13. Check for voltage between each of the driver's under-dash fuse/relay box terminals listed in the table shown in CONNECTED CONTROL UNIT SPECIFICATION , and body ground.
    CONNECTED CONTROL UNIT SPECIFICATION

    Connected Control Unit Driver's under-dash fuse/relay box terminal
    Gauge Control Module N28
    Relay Control Module D11
    Door Multiplex Control Unit J4
    Combination Switch Control Unit X27
    Automatic Lighting Control Unit X18
    MICU-Rear Junction Box G1
    A/C Control Panel/Climate Control Unit N22

    Is there less than 1 V ? 

    1. YES  - Replace a driver's under-dash fuse/relay box.
    2. NO  - Repair a short in the wire between the driver's under-dash fuse/relay box and the affected control unit.
scientia non olet · About LEMON Manuals