LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Honda >> 2004 >> Element EX, 2.4 YH1, Standard >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 1 (Automatic Transmission) >> DTC Troubleshooting >> DTC P1732: Problem in Shift Control System:
April 5, 2026: LEMON Manuals is launched! Read the announcement.

DTC P1732: Problem in Shift Control System:

WARNING: This page is about a different variant/trim than selected.
NOTE: Record all freeze data and review General Troubleshooting Information (see GENERAL TROUBLESHOOTING INFORMATION ) before you troubleshoot.
  1. Warm up the engine to normal operating temperature (the radiator fan comes on).
  2. Make sure that the transmission is filled to the proper level, and check for fluid leaks.
  3. Drain the ATF (see step  3 ) through a strainer. Inspect the strainer for metal debris or excessive clutch material.

    Does the strainer contain metal debris or excessive clutch material? 

    1. YES-  Replace the transmission.
    2. NO-  Replace the ATF (see see step  4 ), then go to step 4.
  4. Clear the DTC with the HDS.
  5. Test-drive the vehicle in the D position through all four gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.
  6. Retest-drive the vehicle in the D position through all four gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.
  7. Monitor the OBD status for P1732 with the DTC Monitor Tool in DTCs/Freeze Data in A/T Mode Menu for a pass/fail.

    Does the result indicate FAILED? 

    1. YES-  Go to step 8.
    2. NO-  If the tester indicates PASSED, intermittent failure, the system is OK at this time. If the tester indicates NOT COMPLETED, return to step  5 and recheck.
  8. Clear the DTC with the HDS.
  9. Select Shift Solenoid B in Miscellaneous Test Menu, and check that shift solenoid valve B operates with the HDS.

    Is a clicking sound heard? 

    1. YES-  Go to step 10.
    2. NO-  Replace shift solenoid valve B (see step SHIFT SOLENOID VALVE REPLACEMENT ), then go to  14.
  10. Select Shift Solenoid C in Miscellaneous Test Menu, and check that shift solenoid valve C operates with the HDS.

    Is a clicking sound heard? 

    1. YES-  Go to step 11.
    2. NO-  Replace shift solenoid valve C (see step SHIFT SOLENOID VALVE REPLACEMENT ), then go to  14.
  11. Test-drive the vehicle in the D position through all four gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.
  12. Retest-drive the vehicle in the D position through all four gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.
  13. Monitor the OBD status for P1732 with the DTC Monitor Tool in DTCs/Freeze Data in A/T Mode Menu for a pass/fail.

    Does the result indicate FAILED? 

    1. YES-  Repair hydraulic system related with shift valves B and C, or replace the transmission, then go to step 14.
    2. NO-  If the tester indicates PASSED, intermittent failure, the system is OK at this time. If the tester indicates NOT COMPLETED, return to step 14 and recheck.
  14. Clear the DTC with the HDS.
  15. Test-drive the vehicle in the D position through all four gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.
  16. Retest-drive the vehicle in the D position through all four gears at speeds over 12 mph (20 km/h) for more than 20 seconds, then slow down to a stop.
  17. Monitor the OBD status for P1732 with the DTC Monitor Tool in DTCs/Freeze Data in A/T Mode Menu for a pass/fail.

    Does the result indicate PASSED? 

    1. YES-  Troubleshooting is complete.
    2. NO-  Return to step  8 and recheck.
scientia non olet · About LEMON Manuals