DTC P0420: Rear Bank Catalyst System Efficiency Below Threshold (Bank 1); DTC P0430: Front Bank Catalyst System Efficiency Below Threshold (Bank 2)
- Before you troubleshoot, record all freeze data and any on-board snapshot, and review the general troubleshooting information (see GENERAL TROUBLESHOOTING INFORMATION ).
- If some of the DTCs listed below are stored at the same time as DTC P0420 and/or P0430*, troubleshoot those DTCs first, then recheck for DTC P0420 and/or P0430*.
P0137, P0138, P0157, P0158: Secondary HO2S (Sensor 2)
P0141, P0161: Secondary HO2S (Sensor 2) heater
- Poor quality fuel can cause these DTCs.
- Information marked with an asterisk (*) applies to the front bank (Bank 2).
- Turn the ignition switch to ON (II).
- Clear the DTC with the HDS.
- Start the engine. Hold the engine speed at 3, 000 rpm without load (in P or N) until the radiator fan comes on, then let it idle.
- Test-drive under these conditions:
- Engine coolant temperature (ECT SENSOR 1) above 158°F(70°C)
- Transmission in D
- Vehicle speed between 45-75 mph (72-120 km/h) for 5 minutes or more with cruise control set
- Vehicle speed between 55-75 mph (88-120 km/h) for 10 seconds, then decelerate (with the throttle fully closed). Repeat this three or more times
- Maintain the vehicle speed at 55 mph (88 km/h) for 5 minutes or more with cruise control set
- Monitor the OBD STATUS for DTC P0420 and/or P0430* in the DTCs MENU with the HDS.
Does the HDS indicate FAILED?
YES -Go to next step.
NO -If the HDS indicates PASSED, intermittent failure, the system is OK at this time. If the HDS indicates EXECUTING, keep driving until a result comes on. If the HDS indicates OUT OF CONDITION or NOT COMPLETED, go to step 4 and recheck.
- Continue test driving until a result comes on.
- Monitor the OBD STATUS for DTC P0420 and/or P0430 in the DTCs MENU with the HDS.
Does the HDS indicate FAILED?
YES -Go to next step.
NO -If the HDS indicates PASSED, intermittent failure, the system is OK at this time. If the HDS indicates EXECUTING, keep driving until a result comes on. If the HDS indicates OUT OF CONDITION or NOT COMPLETED, go to step 4 and recheck.
- Turn the ignition switch to LOCK (0).
- Replace the WU-TWC:
- For DTC P0420, replace the rear WU-TWC (Bank 1) (see REAR WU-TWC (BANK 1) ).
- For DTC P0430, replace the front WU-TWC (Bank 2). (see WARM UP TWC REMOVAL/INSTALLATION )
- Turn the ignition switch to ON (II).
- Reset the PCM with the HDS.
- Do the PCM idle learn procedure (see PCM IDLE LEARN PROCEDURE ).
- Test-drive for about 10 minutes, continually changing the vehicle speed.
- Check the CATA MONITOR CONDITION B1 (B2)* in the DATA LIST with the HDS.
Is the condition OK?
YES -Go to next step.
NO -Go to step 13 and recheck.
- Test-drive under these conditions:
- Engine coolant temperature (ECT SENSOR 1) above 158 °F (70 °C)
- Transmission in D
- Vehicle speed between 55-75 mph (88-120 km/h) for 10 seconds, then decelerate (with the throttle fully closed). Repeat this three or more times
- Maintain the vehicle speed at 55 mph (88 km/h) for 5 minutes or more with cruise control set
- Continue test driving until a result comes on.
- Check for Pending or Confirmed DTCs with the HDS.
Is DTC P0420 and/or P0430* indicated?
YES -Check the fuel quality, then go to step 1.
NO -Go to next step.
- Monitor the OBD STATUS for DTC P0420 and/or P0430* in the DTCs MENU with the HDS.
Does the HDS indicate PASSED?
YES -Troubleshooting is complete. If any other Pending or Confirmed DTCs were indicated in step 17, go to the indicated DTC's troubleshooting.
NO -If the HDS indicates FAILED, check the fuel quality, then go to step 1. If the HDS indicates EXECUTING, keep driving until a result comes on. If the HDS indicates OUT OF CONDITION or NOT COMPLETED, go to step 15.