LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Honda >> 2007 >> Fit Base, Standard >> Repair and Diagnosis >> Accessories & Equipment >> Cruise Control Systems >> Symptom Troubleshooting Index
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Symptom Troubleshooting Index

SYMPTOM TROUBLESHOOTING CHART

Symptom Diagnostic procedure Also check for
Cruise control cannot be set
  1. Check for PGM-FI DTCs (see GENERAL TROUBLESHOOTING INFORMATION ).
  2. Check the No. 16 (15 A) fuse in the under-hood fuse/relay box, and the No. 3 (10 A) fuse in the under-dash fuse/relay box.
  3. Do the CRUISE CONTROL INPUT TEST  .
  4. Do the cruise control combination switch test (see CRUISE CONTROL COMBINATION SWITCH TEST/REPLACEMENT ).
 Poor ground G101 (A/T) or G402 (M/T)
Cruise control can be set, but the cruise main indicator does not come on
  1. Check for PGM-FI DTCs (see GENERAL TROUBLESHOOTING INFORMATION ).
  2. Do the gauge control module self-diagnostic function (see SELF-DIAGNOSTIC FUNCTION ).
  3. Do the CRUISE CONTROL INPUT TEST  .
 Faulty gauge control module
Cruise control can be set, but the cruise control indicator does not come on
  1. Check for PGM-FI DTCs (see GENERAL TROUBLESHOOTING INFORMATION ).
  2. Do the gauge control module self-diagnostic function (see SELF-DIAGNOSTIC FUNCTION ).
  3. Do the CRUISE CONTROL INPUT TEST  . Test the cruise control indicator signal input.
 Faulty gauge control module
Vehicle does not decelerate or accelerate accordingly when the set/ decel or resume/accel switch is pressed
  1. Check for PGM-FI DTCs (see GENERAL TROUBLESHOOTING INFORMATION ).
  2. Do the CRUISE CONTROL INPUT TEST  . Test the set/decel, resume/accel switch signal input.
  3. Do the cruise control combination switch test (see CRUISE CONTROL COMBINATION SWITCH TEST/REPLACEMENT ).
 Open circuit, loose or disconnected terminals: LT GRN/BLK or GRY/RED wire
Set speed does not cancel when the brake pedal is pressed
  1. Check for PGM-FI DTCs (see GENERAL TROUBLESHOOTING INFORMATION ).
  2. Do the CRUISE CONTROL INPUT TEST  . Test the brake pedal position switch signal input.
  3. Do the brake pedal position switch test (see BRAKE PEDAL POSITION SWITCH TEST ).
  • Short to power in the BLU wire
  • Faulty brake pedal position switch
Set speed does not cancel (engine rpm stays high) when the clutch pedal is pressed (M/T)
  1. Check for PGM-FI DTCs (see GENERAL TROUBLESHOOTING INFORMATION ).
  2. Do the CRUISE CONTROL INPUT TEST  . Test the clutch pedal position switch signal input.
  3. Do the CLUTCH PEDAL POSITION SWITCH TEST  .
 Short to ground in the LT BLU wire
Set speed does not cancel when the cruise control main switch is pressed
  1. Check for PGM-FI DTCs (see GENERAL TROUBLESHOOTING INFORMATION ).
  2. Do the CRUISE CONTROL INPUT TEST  . Test the cruise control main switch signal input.
  3. Do the cruise control combination switch test (see CRUISE CONTROL COMBINATION SWITCH TEST/REPLACEMENT ).
 Short to ground in the PUR wire
Set speed does not cancel when the cancel switch is pressed
  1. Check for PGM-FI DTCs (see GENERAL TROUBLESHOOTING INFORMATION ).
  2. Do the CRUISE CONTROL INPUT TEST  . Test the cancel switch signal input.
  3. Do the cruise control combination switch test (see CRUISE CONTROL COMBINATION SWITCH TEST/REPLACEMENT ).
 Open circuit, loose or disconnected terminals: LT GRN/BLK or GRY/RED wire
Set speed will not resume when the resume/accel switch is pressed (with the cruise control main switch turned on, and set speed temporarily canceled by pressing the brake pedal)
  1. Check for PGM-FI DTCs (see GENERAL TROUBLESHOOTING INFORMATION ).
  2. Check the brake pedal position switch adjustment (see BRAKE PEDAL AND BRAKE PEDAL POSITION SWITCH ADJUSTMENT ).
  3. Do the CRUISE CONTROL INPUT TEST  .

    Test the resume/accel switch signal input.

    Test the brake pedal position switch signal input.

  4. Do the cruise control combination switch test (see CRUISE CONTROL COMBINATION SWITCH TEST/REPLACEMENT ).
  • Open circuit, loose or disconnected terminals: LT GRN/BLK wire
  • Faulty brake pedal position switch
Set speed will not resume when the resume/accel switch is pressed (with the cruise control main switch turned on, and set speed temporarily canceled by pressing the clutch pedal) (M/T)
  1. Check for PGM-FI DTCs (see GENERAL TROUBLESHOOTING INFORMATION ).
  2. Check the clutch pedal position switch adjustment (see CLUTCH PEDAL, CLUTCH PEDAL POSITION SWITCH, AND CLUTCH INTERLOCK SWITCH ADJUSTMENT ).
  3. Do the CRUISE CONTROL INPUT TEST  .

    Test the resume/accel switch signal input.

    Test the clutch pedal position switch signal input.

  4. Do the cruise control combination switch test (see CRUISE CONTROL COMBINATION SWITCH TEST/REPLACEMENT ).
  • Open circuit, loose or disconnected terminals: LT GRN/BLK wire
  • Faulty clutch pedal position switch
With the ignition switch ON (II), and the lighting switch turned on, the cruise control combination switch illumination does not come on Do the cruise control combination switch test (see CRUISE CONTROL COMBINATION SWITCH TEST/REPLACEMENT ).  
scientia non olet · About LEMON Manuals