Front Seat-back Cover/Pad Replacement

Special Tools Required

KTC trim tool set SOJATP2014 *

* Available through the American Honda Tool and Equipment Program; call 888-424-6857

SRS components are located in this area. Review the SRS component locations (see COMPONENT LOCATION INDEX ) and the precautions and procedures (see PRECAUTIONS AND PROCEDURES ) before doing repairs or service.

Check the operation of the driver's seat position sensor after any of these actions (see DRIVER'S SEAT POSITION SENSOR OPERATION CHECK ):
- Driver's seat position sensor replacement
- Cover plate (front side of driver's seat slide rail) replacement
Calibrate the ODS unit after any of these actions (see ODS UNIT CALIBRATION ):
- Front passenger's seat replacement (including any seat components)
- Replacement of the seat weight sensors
- After a vehicle collision

NOTE:

Take care not to tear the seams or damage the seat covers.
On the passenger's seat, do not touch the ODS sensor in the seat-back pad, and keep it away from oil. Oil can corrode the sensor causing it to fail.
Put on gloves to protect your hands.

Remove the front seat:
- See DRIVER'S SEAT
- See PASSENGER'S SEAT
Separate the seat-back and the seat cushion (see FRONT SEAT DISASSEMBLY/REASSEMBLY ).
Remove the retainer clip (A), then remove the slide knob (B). Remove the screw and release the hooks (C), then remove the slide knob trim (D).

Fig 1: Identifying Retainer Clip, Slide Knob, Hooks And Slide Knob Trim
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Release the hook (A), and unzip the seat-back cover (B).

Fig 2: Identifying Seat-Back Cover Hook
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Fold back the seat-back cover (A), then release the hooks (B) and hook springs (C). Pull the side airbag harness (D) and the slide cable (E) on each of the seats, and the ODS subharness (F) on the passenger's seat out through the harness guides (G). The passenger's seat is shown; the driver's seat is similar.

Fig 3: Identifying Seat-Back Cover, Side Airbag Harness, ODS Subharness And Slide Cable
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Remove the side airbag (see SIDE AIRBAG REPLACEMENT ), and release the hooks (A) from the side airbag module holder (B). Detach the clips (C) by pulling the holder back, then remove it.

Fig 4: Removing Side Airbag Module Holder
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Passenger's seat: Remove the ODS unit cover, and disconnect the OPDS sensor connectors from the ODS unit (see ODS UNIT REPLACEMENT ).
Passenger's seat: Release the wire ties (A) fastening the OPDS sensor harnesses (B) to the seat-back frame spring (C).

Fig 5: Identifying Wire Ties, OPDS Sensor Harnesses And Seat-Back Frame Spring
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Pull out the head restraint guides (A) while pinching the end of the guides, and remove them.

Fig 6: Identifying Head Restraint Guides
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Remove the seat-back cover/pad (A) from the seat-back frame (B). Take care not to tear the pad while removing the outside shoulder portion of it from the slide bracket (C) of the frame.

Fig 7: Identifying Seat-Back Cover/Pad, Seat-Back Frame And Slide Bracket
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Install the seat-back cover/pad in the reverse order of removal, and note these items:
- Reinitialize the ODS unit (see ODS UNIT INITIALIZATION ).
- Make sure the slide cable is connected securely.
- Replace the wire ties with new ones.
- To prevent wrinkles when installing a seat-back cover, make sure the material is stretched evenly over the pad before securing the hooks and hook springs.