LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Honda >> 2007 >> Fit Base, Standard >> Repair and Diagnosis >> Engine Performance >> System >> PGM-FI System >> DTC Troubleshooting >> DTC P2195: A/F Sensor (Sensor 1) Signal Stuck Lean
April 5, 2026: LEMON Manuals is launched! Read the announcement.

DTC P2195: A/F Sensor (Sensor 1) Signal Stuck Lean

NOTE:
  • Before you troubleshoot, record all freeze data and any on-board snapshot, and review the general troubleshooting information (see GENERAL TROUBLESHOOTING INFORMATION ).
  • If the vehicle was out of fuel and the engine stalled before this DTC was stored, refuel, then clear the DTC with the HDS.
  • If DTC P2101, P2108, P2118, P2135, P2138, P2176, U0107, or a combination of P2122 and P2127, P2122, and P2138, or P2127 and P2138 is stored at the same time, troubleshoot them first, then recheck for DTC P2195.
  1. Check the installation of the A/F sensor (Sensor 1).

    Is the A/F sensor loose or disconnected from the exhaust pipe? 

    YES  - Go to step  6.

    NO  - Go to step  2.

  2. Turn the ignition switch ON (II).
  3. Clear the DTC with the HDS.
  4. Start the engine, then let it idle.
  5. Check for Temporary DTCs or DTCs with the HDS.

    Are any Temporary DTCs or DTCs indicated? 

    YES  - If DTC P2195 is indicated, check for poor connections or loose terminals at the A/F sensor (Sensor 1) and the ECM/PCM, then go to step  13. If any other Temporary DTCs or DTCs are indicated, go to the indicated DTCs troubleshooting.

    NO  - Intermittent failure, the system is OK at this time. Check for poor connections or loose terminals at the A/F sensor (Sensor 1) and the ECM/PCM.

  6. Turn the ignition switch OFF.
  7. Reinstall the A/F sensor (Sensor 1) (see A/F SENSOR REPLACEMENT ).
  8. Turn the ignition switch ON (II).
  9. Reset the ECM/PCM with the HDS.
  10. Do the ECM/PCM idle learn procedure (see ECM/PCM IDLE LEARN PROCEDURE ).
  11. Check for Temporary DTCs or DTCs with the HDS.

    Is DTC P2195 indicated? 

    YES  - Check for poor connections or loose terminals at the A/F sensor (Sensor 1) and the ECM/PCM, then go to step  1.

    NO  - Go to step  12.

  12. Monitor the OBD STATUS for DTC P2195 in the DTCs MENU with the HDS.

    Does the screen indicate PASSED? 

    YES  - Troubleshooting is complete. If any other Temporary DTCs or DTCs were indicated in step 11, go to the indicated DTCs troubleshooting.

    NO  - If the screen indicates FAILED, check for poor connections or loose terminals at the A/F sensor (Sensor 1) and the ECM/PCM, then go to step  1. If the screen indicated NOT COMPLETED, go to step  10.

  13. Update the ECM/PCM if it does not have the latest software (see UPDATING THE ECM/PCM ), or substitute a known-good ECM/PCM (see SUBSTITUTING THE ECM/PCM ).
  14. Start the engine, then let it idle.
  15. Check for Temporary DTCs or DTCs with the HDS.

    Is DTC P2195 indicated? 

    YES  - Check for poor connections or loose terminals at the A/F sensor (Sensor 1) and the ECM/PCM. If the ECM/PCM was updated, substitute a known-good ECM/PCM (see SUBSTITUTING THE ECM/PCM ), then go to step  14. If the ECM/PCM was substituted, go to step  1.

    NO  - Go to step  16.

  16. Monitor the OBD STATUS for DTC P2195 in the DTCs MENU with the HDS.

    Does the screen indicate PASSED? 

    YES  - If the ECM/PCM was updated, troubleshooting is complete. If the ECM/PCM was substituted, replace the original ECM/PCM (see ECM/PCM REPLACEMENT ). If any other Temporary DTCs or DTCs were indicated in step 15, go to the indicated DTCs troubleshooting.

    NO  - If the screen indicates FAILED, check for poor connections or loose terminals at the A/F sensor (Sensor 1) and the ECM/PCM. If the ECM/PCM was updated, substitute a known-good ECM/PCM (see SUBSTITUTING THE ECM/PCM ), then go to step  14. If the ECM/PCM was substituted, go to step  1. If the screen indicates NOT COMPLETED, go to step  14.

scientia non olet · About LEMON Manuals