LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Honda >> 2007 >> Odyssey EX >> Repair and Diagnosis >> Engine Performance >> System >> PGM-FI System >> DTC Troubleshooting >> DTC P0133: Rear A/F Sensor (Bank 1, Sensor 1) Circuit Slow Response; DTC P0153: Front A/F Sensor (Bank 2, Sensor 1) Circuit Slow Response
April 5, 2026: LEMON Manuals is launched! Read the announcement.

DTC P0133: Rear A/F Sensor (Bank 1, Sensor 1) Circuit Slow Response; DTC P0153: Front A/F Sensor (Bank 2, Sensor 1) Circuit Slow Response

NOTE:
  • Before you troubleshoot, record all freeze data and any on-board snapshot, and review the general troubleshooting information (see GENERAL TROUBLESHOOTING INFORMATION ).
  • If DTC P0139 and/or P0159* is stored at the same time as DTC P0133 and/or P0153*, troubleshoot DTC P0139 and/or P0159* first, then recheck for DTC P0133 and/or P0153*.
  • Information marked with an asterisk (*) applies to the front bank (Bank 2).
  1. Turn the ignition switch to ON (II).
  2. Clear the DTC with the HDS.
  3. Start the engine. Hold the engine speed at 3,000 rpm without load (in P or N) until the radiator fan comes on, then let it idle.
  4. Test-drive under these conditions:
    • Engine coolant temperature (ECT SENSOR 1) above 158°F (70°C)
    • Transmission in D
    • Drive the vehicle at 25 mph (40 km/h) or less for 5 minutes, then drive at a steady speed between 32-81 mph (52-130 km/h)
    • '08-10 models: Engine speed between 1,250 and 2,200 rpm
  5. Monitor the OBD STATUS for DTC P0133 and/or P0153* in the DTCs MENU with the HDS.

    Does the screen indicate FAILED? 

    YES  -Go to step 6.

    NO  -If the screen indicates PASSED, intermittent failure, the system is OK at this time. Check for poor connections or loose terminals at the A/F sensor (Sensor 1) and the PCM. If the screen indicates EXECUTING, keep driving until a result comes on. If the screen indicates OUT OF CONDITION or NOT COMPLETED, go to step  3 and recheck.

  6. Turn the ignition switch to LOCK (0).
  7. Replace the A/F sensor (Sensor 1) (see A/F SENSOR REPLACEMENT  ).
  8. Turn the ignition switch to ON (II).
  9. Reset the PCM with the HDS.
  10. Do the PCM idle learn procedure (see PCM IDLE LEARN PROCEDURE ).
  11. Start the engine. Hold the engine speed at 3,000 rpm without load (in P or N) until the radiator fan comes on, then let it idle.
  12. Test-drive under these conditions:
    • Engine coolant temperature (ECT SENSOR 1) above 158°F (70°C)
    • Transmission in D
    • Drive the vehicle at 25 mph (40 km/h) or less for 5 minutes, then drive at a steady speed between 32-81 mph (52-130 km/h)
    • '08-10 models: Engine speed between 1,250 and 2,200 rpm
  13. Check for Pending or Confirmed DTC's with the HDS.

    Is DTC P0133 and/or P0153* indicated? 

    YES  -Check for poor connections or loose terminals at the A/F sensor (Sensor 1) and the PCM, then go to step  1.

    NO  -Go to step 14.

  14. Monitor the OBD STATUS for DTC P0133 and/or P0153* in the DTCs MENU with the HDS.

    Does the screen indicate PASSED? 

    YES  -Troubleshooting is complete. If any other Pending or Confirmed DTC's were indicated in step  13, go to the indicated DTC'S TROUBLESHOOTING .

    NO  -If the screen indicates FAILED, check for poor connections or loose terminals at the A/F sensor (Sensor 1) and the PCM, then go to step  1. If the screen indicates EXECUTING, keep driving until a result comes on. If the screen indicates OUT OF CONDITION or NOT COMPLETED, go to step  12.

scientia non olet · About LEMON Manuals