| Cruise control cannot be set |
- Check the No. B24 (10 A) fuse and the No. B12 (10 A) fuse in the under-dash fuse/relay box.
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
- Do the cruise control combination switch test (see CRUISE CONTROL COMBINATION SWITCH TEST/REPLACEMENT
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
).
|
Poor ground G502, T10 |
| Cruise control can be set, but cruise main indicator does not come on |
- Do the gauge control module self-diagnostic function procedure (see
SELF-DIAGNOSTIC FUNCTION
).
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
).
|
Faulty gauge control module |
| Cruise control can be set, but cruise control indicator does not come on |
- Do the gauge control module self-diagnostic function procedure (see
SELF-DIAGNOSTIC FUNCTION
).
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
).
Test the cruise control indicator signal input.
|
Faulty gauge control module |
| Vehicle does not accelerate accordingly when the resume/accel button is pressed |
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
- Do the cruise control combination switch test (see CRUISE CONTROL COMBINATION SWITCH TEST/REPLACEMENT
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
).
Test the cruise control resume/accel switch signal input.
|
Open circuit, loose or disconnected terminals: BRN or BLU wire |
| Set speed does not cancel when the brake pedal is pressed |
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
- Do the brake pedal position switch test (M/T model) (see
BRAKE PEDAL POSITION SWITCH TEST
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
).
Test the cruise brake pedal position switch signal input (M/T model).
Test the idle stop switch signal input (CVT model).
|
- Short to power on the BRN wire
- Faulty brake pedal position switch (M/T model)
- Faulty idle stop switch (CVT model)
|
| Set speed does not cancel (engine rpm stays high) when the clutch pedal is pressed (M/T model) |
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
- Do the clutch pedal position switch B test (see CLUTCH PEDAL POSITION SWITCH B TEST
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
).
Test the clutch pedal position switch B signal input.
|
- Short to power on the LT GRN wire
- Faulty clutch pedal position switch B
|
| Set speed does not cancel when the cruise control main button is pressed |
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
- Do the cruise control combination switch test (see CRUISE CONTROL COMBINATION SWITCH TEST/REPLACEMENT
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
).
Test the cruise control main switch signal input.
|
Short to ground on the LT GRN, PNK wire |
| Set speed does not cancel when the cancel button is pressed |
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
- Do the cruise control combination switch test (see CRUISE CONTROL COMBINATION SWITCH TEST/REPLACEMENT
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
).
Test the cruise control cancel switch signal input.
|
Open circuit, loose or disconnected terminals: GRY, RED or BRN, BLU wire |
| Set speed does not resume when the resume/accel button is pressed (with the cruise control main button pressed on, and set speed temporarily canceled by pressing the brake pedal) |
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
- Do the cruise control combination switch test (see CRUISE CONTROL COMBINATION SWITCH TEST/REPLACEMENT
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
).
Test the cruise control resume/accel switch signal input.
Test the brake pedal position switch signal input.
|
- Open circuit, loose or disconnected terminals: BRN, BLU wire
- Faulty brake pedal position switch
|
| Set speed does not resume when the resume/accel button is pressed (with the cruise control main button pressed on, and set speed temporarily canceled by pressing the clutch pedal) (M/T model) |
- Check for PGM-FI DTCs (see
GENERAL TROUBLESHOOTING INFORMATION
).
- Do the cruise control combination switch test (see CRUISE CONTROL COMBINATION SWITCH TEST/REPLACEMENT
).
- Do the cruise control input test (see CRUISE CONTROL INPUT TEST
).
Test the cruise control resume/accel switch signal input.
Test the clutch pedal position switch B signal input.
|
- Open circuit, loose or disconnected terminals: BRN, BLU wire
- Faulty clutch pedal position switch B
|
| Light switch turned on, the cruise control combination switch illumination does not come on |
- Check the No. B29 (10 A) fuse in the under-dash fuse/relay box.
- Do the cruise control combination switch test (see CRUISE CONTROL COMBINATION SWITCH TEST/REPLACEMENT
).
- Do the audio remote switch test (see
SUBWOOFER
).
|
Open circuit, loose or disconnected terminals: RED, BLU and WHT wire |