Security alarm system will not arm (2014 - 2015)

WARNING: This page is about a different variant/trim than selected.

NOTE:

Refer to the Electrical Wiring Diagrams for the location of the under-dash fuse/relay box connectors.
Before troubleshooting, check the B-CAN DTCs. If any DTC is indicated, troubleshoot the indicated DTC first.

Switch information check:
- 1. Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode.

- 2. Select SECURITY from the BODY ELECTRICAL menu, and enter the DATA LIST with the HDS.

- 3. Check the ON/OFF information in the DATA LIST when each switch is operating.
- TRUNK LID/TAILGATE SWITCH
- SECURITY HOOD SWITCH
- DRIVER'S DOOR LOCK KNOB SWITCH (UNLOCK)
- FRONT PASSENGER'S DOOR LOCK KNOB SW (UNLOCK)
- DRIVER'S REAR DOOR LOCK KNOB SW (UNLOCK)
- PASSENGER'S REAR DOOR LOCK KNOB SW (UNLOCK)
- DRIVER'S DOOR SWITCH
- FRONT PASSENGER'S DOOR SWITCH
- LEFT REAR DOOR SWITCH
- RIGHT REAR DOOR SWITCH
- DRIVER'S DOOR KEY CYLINDER SWITCH (LOCK)
- DRIVER'S DOOR KEY CYLINDER SWITCH (UNLOCK)
Is each switch information OK?

YES

Intermittent failure, the system is OK at this time.

NG

Trunk lid latch switch circuit troubleshooting: go to step2.

NG

Security hood switch circuit troubleshooting: go to step8.

NG

Driver's door lock knob switch circuit troubleshooting: go to step 14.

NG

Front passenger's door lock knob switch circuit troubleshooting: go to step 20.

NG

Left rear door lock knob switch circuit troubleshooting: go to step 26.

NG

Right rear door lock knob switch circuit troubleshooting: go to step 32.

NG

Driver's door switch circuit troubleshooting: go to step 38.

NG

Front passenger's door switch circuit troubleshooting: go to step 43.

NG

Left rear door switch circuit troubleshooting: go to step 48.

NG

Right rear door switch circuit troubleshooting: go to step 53.

NG

Driver's door key cylinder switch circuit troubleshooting: go to step 58.
Keyless/power door locks/security system check 1:
- 1. With the trunk closed, select SECURITY with the HDS, and enter the DATA LIST.

- 2. Check the ON/OFF information of the TRUNK LID/TAILGATE SWITCH in the DATA LIST.

Is information indicator ON?

YES

Go to step3.

NO

Go to step5.
Determine possible failure area (trunk lid latch switch, others):
- 1. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

- 2. Disconnect the following connector.

Trunk lid release actuator/latch switch 3P connector

- 3. Check the ON/OFF information of the TRUNK LID/TAILGATE SWITCH in the DATA LIST.

Is information indicator OFF?

YES

Faulty trunk lid latch switch, replace the trunk lid latch .

NO

Go to step4.

Shorted wire check (TRUNK_SW line):

- 1. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

- 2. Disconnect the following connector.

Under-dash fuse/relay box connector B (44P)

- 3. Check for continuity between test points 1 and 2.

Test condition	IG LOCK (0) or OFF mode Trunk lid release actuator/latch switch 3P connector: disconnected Under-dash fuse/relay box connector B (44P): disconnected
Test circuit	TRUNK_SW
Test point 1	Under-dash fuse/relay box connector B (44P) No. 22 (BLU)
Test point 2	Body ground

Courtesy of HONDA, U.S.A., INC.

Is there continuity?

YES

Repair a short to ground in the wire.

Faulty MICU, replace the under-dash fuse/relay box - Refer to: Under-Dash Fuse/Relay Box Removal and Installation (KA models with Keyless Access System), or Under-Dash Fuse/Relay Box Removal and Installation (KA KX models without Keyless Access System) .

Keyless/power door locks/security system check 2:

- 1. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

- 2. Disconnect the following connector.

Trunk lid release actuator/latch switch 3P connector

- 3. Connect test points 1 and 2 with a jumper wire.

Test point 1	Trunk lid release actuator/latch switch 3P connector No. 3 (BLU)
Test point 2	Body ground

Courtesy of HONDA, U.S.A., INC.

- 4. Check the ON/OFF information of the TRUNK LID/TAILGATE SWITCH in the DATA LIST.

Is information indicator ON?

YES

Go to step6.

Go to step7.

Open wire check (GND line):

- 1. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

- 2. Check for continuity between test points 1 and 2.

Test condition	IG LOCK (0) or OFF mode Trunk lid release actuator/latch switch 3P connector: disconnected
Test circuit	GND
Test point 1	Trunk lid release actuator/latch switch 3P connector No. 2 (BLK)
Test point 2	Body ground

Courtesy of HONDA, U.S.A., INC.

Is there continuity?

YES

Faulty trunk lid latch switch, replace the trunk lid latch .

Repair an open or high resistance in the ground wire or poor ground (G701).

Open wire check (TRUNK_SW line):

- 1. Connect test points 1 and 2 with a jumper wire.

Test point 1	Under-dash fuse/relay box connector B (44P) No. 22 (BLU)
Test point 2	Body ground

Courtesy of HONDA, U.S.A., INC.

- 2. Check the ON/OFF information of the TRUNK LID/TAILGATE SWITCH in the DATA LIST.

Is information indicator ON?

YES

Repair an open or high resistance in the wire.

Keyless/power door locks/security system check 1:
- 1. With the hood closed, select SECURITY with the HDS, and enter the DATA LIST.

- 2. Check the ON/OFF information of the SECURITY HOOD SWITCH in the DATA LIST.

Is information indicator OFF?

YES

Go to step9.

NO

Go to step11.
Determine possible failure area (hood latch, others):
- 1. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

- 2. Disconnect the following connector.

Security hood switch 2P connector

- 3. Check the ON/OFF information of the SECURITY HOOD SWITCH in the DATA LIST.

Is information indicator ON?

YES

Faulty security hood switch, replace the hood latch .

NO

Go to step10.

10.Shorted wire check (HOOD_SW line):

- 1. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

- 2. Disconnect the following connector.

Under-dash fuse/relay box connector C (38P)

- 3. Check for continuity between test points 1 and 2.

Test condition	IG LOCK (0) or OFF mode Security hood switch 2P connector: disconnected Under-dash fuse/relay box connector C (38P): disconnected
Test circuit	HOOD_SW
Test point 1	Under-dash fuse/relay box connector C (38P) No. 27 (LT BLU)
Test point 2	Body ground

Courtesy of HONDA, U.S.A., INC.

Is there continuity?

YES

Repair a short to ground in the wire.

11.Keyless/power door locks/security system check 2:

- 1. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

- 2. Disconnect the following connector.

Security hood switch 2P connector

- 3. Connect test points 1 and 2 with a jumper wire.

Test point 1	Security hood switch 2P connector No. 1 (LT BLU)
Test point 2	Body ground

Courtesy of HONDA, U.S.A., INC.

- 4. Check the ON/OFF information of the SECURITY HOOD SWITCH in the DATA LIST.

Is information indicator OFF?

YES

Go to step12.

Go to step13.

12.Open wire check (GND line):

- 1. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

- 2. Check for continuity between test points 1 and 2.

Test condition	IG LOCK (0) or OFF mode Security hood switch 2P connector: disconnected
Test circuit	GND
Test point 1	Security hood switch 2P connector No. 2 (BLK)
Test point 2	Body ground

Courtesy of HONDA, U.S.A., INC.

Is there continuity?

YES

Faulty security hood switch, replace the hood latch .

Repair an open or high resistance in the ground wire or poor ground (G401).

13.Open wire check (HOOD_SW line):

- 1. Connect test points 1 and 2 with a jumper wire.

Test point 1	Under-dash fuse/relay box connector C (38P) No. 27 (LT BLU)
Test point 2	Body ground

Courtesy of HONDA, U.S.A., INC.

- 2. Check the ON/OFF information of the SECURITY HOOD SWITCH in the DATA LIST.

Is information indicator OFF?

YES

Repair an open or high resistance in the wire.

14.Keyless/power door locks/security system check 1:
- 1. With the driver's door lock knob switch in LOCK position, select SECURITY with the HDS, and enter the DATA LIST.

- 2. Check the ON/OFF information of the DRIVER'S DOOR LOCK KNOB SWITCH (UNLOCK) in the DATA LIST.

Is information indicator ON?

YES

Go to step15.

NO

Go to step17.
15.Determine possible failure area (driver's door latch, others):
- 1. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

- 2. Disconnect the following connector.

Driver's door latch 10P connector

- 3. Check the ON/OFF information of the DRIVER'S DOOR LOCK KNOB SWITCH (UNLOCK) in the DATA LIST.

Is information indicator OFF?

YES

Faulty driver's door lock knob switch, replace the driver's door latch .

NO

Go to step16.

16.Shorted wire check (DR_SILCON_UNLOCK line):

- 1. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

- 2. Disconnect the following connector.

Under-dash fuse/relay box connector X (10P)

- 3. Check for continuity between test points 1 and 2.

Test condition	IG LOCK (0) or OFF mode Driver's door latch 10P connector: disconnected Under-dash fuse/relay box connector X (10P): disconnected
Test circuit	DR_SILCON_UNLOCK
Test point 1	Under-dash fuse/relay box connector X (10P) No. 4 (WHT)
Test point 2	Body ground

Courtesy of HONDA, U.S.A., INC.

Is there continuity?

YES

Repair a short to ground in the wire.

17.Keyless/power door locks/security system check 2:

- 1. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

- 2. Disconnect the following connector.

Driver's door latch 10P connector

- 3. Connect test points 1 and 2 with a jumper wire.

Test point 1	Driver's door latch 10P connector No. 5 (WHT)
Test point 2	Body ground

Courtesy of HONDA, U.S.A., INC.

- 4. Check the ON/OFF information of the DRIVER'S DOOR LOCK KNOB SWITCH (UNLOCK) in the DATA LIST.

Is information indicator ON?

YES

Go to step18.

Go to step19.

18.Open wire check (GND line):

- 1. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

- 2. Check for continuity between test points 1 and 2.

Test condition	IG LOCK (0) or OFF mode Driver's door latch 10P connector: disconnected
Test circuit	GND
Test point 1	Driver's door latch 10P connector No. 7 (BLK)
Test point 2	Body ground

Courtesy of HONDA, U.S.A., INC.

Is there continuity?

YES

Faulty driver's door lock knob switch, replace the driver's door latch .

Repair an open or high resistance in the ground wire or poor ground (G502).

19.Open wire check (DR_SILCON_UNLOCK line):

- 1. Connect test points 1 and 2 with a jumper wire.

Test point 1	Under-dash fuse/relay box connector X (10P) No. 4 (WHT)
Test point 2	Body ground

Courtesy of HONDA, U.S.A., INC.

- 2. Check the ON/OFF information of the DRIVER'S DOOR LOCK KNOB SWITCH (UNLOCK) in the DATA LIST.

Is information indicator ON?

YES

Repair an open or high resistance in the wire.

20.Keyless/power door locks/security system check 1:
- 1. With the front passenger's door lock knob switch in LOCK position, select SECURITY with the HDS, and enter the DATA LIST.

- 2. Check the ON/OFF information of the FRONT PASSENGER'S DOOR LOCK KNOB SWITCH (UNLOCK) in the DATA LIST.

Is information indicator ON?

YES

Go to step21.

NO

Go to step23.
21.Determine possible failure area (front passenger's door latch, others):
- 1. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

- 2. Disconnect the following connector.

Front passenger's door latch 10P connector

- 3. Check the ON/OFF information of the FRONT PASSENGER'S DOOR LOCK KNOB SWITCH (UNLOCK) in the DATA LIST.

Is information indicator OFF?

YES

Faulty front passenger's door lock knob switch, replace the front passenger's door latch .

NO

Go to step22.

22.Shorted wire check (AS_SILCON_UNLOCK line):

- 1. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

- 2. Disconnect the following connector.

Under-dash fuse/relay box connector W (24P)

- 3. Check for continuity between test points 1 and 2.

Test condition	IG LOCK (0) or OFF mode Front passenger's door latch 10P connector: disconnected Under-dash fuse/relay box connector W (24P): disconnected
Test circuit	AS_SILCON_UNLOCK
Test point 1	Under-dash fuse/relay box connector W (24P) No. 10 (LT BLU)
Test point 2	Body ground

Courtesy of HONDA, U.S.A., INC.

Is there continuity?

YES

Repair a short to ground in the wire.

23.Keyless/power door locks/security system check 2:

- 1. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

- 2. Disconnect the following connector.

Front passenger's door latch 10P connector

- 3. Connect test points 1 and 2 with a jumper wire.

Test point 1	Front passenger's door latch 10P connector No. 10 (WHT)
Test point 2	Body ground

Courtesy of HONDA, U.S.A., INC.

- 4. Check the ON/OFF information of the FRONT PASSENGER'S DOOR LOCK KNOB SWITCH (UNLOCK) in the DATA LIST.

Is information indicator ON?

YES

Go to step 24.

Go to step 25.

24.Open wire check (GND line):

- 1. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

- 2. Check for continuity between test points 1 and 2.

Test condition	IG LOCK (0) or OFF mode Front passenger's door latch 10P connector: disconnected
Test circuit	GND
Test point 1	Front passenger's door latch 10P connector No. 8 (BLK)
Test point 2	Body ground

Courtesy of HONDA, U.S.A., INC.

Is there continuity?

YES

Faulty front passenger's door lock knob switch, replace the front passenger's door latch .

Repair an open or high resistance in the ground wire or poor ground (G504).

25.Open wire check (AS_SILCON_UNLOCK line):

- 1. Connect test points 1 and 2 with a jumper wire.

Test point 1	Under-dash fuse/relay box connector W (24P) No. 10 (LT BLU)
Test point 2	Body ground

Courtesy of HONDA, U.S.A., INC.

- 2. Check the ON/OFF information of the FRONT PASSENGER'S DOOR LOCK KNOB SWITCH (UNLOCK) in the DATA LIST.

Is information indicator ON?

YES

Repair an open or high resistance in the wire.

26.Keyless/power door locks/security system check 1:
- 1. With the left rear door lock knob switch in LOCK position, select SECURITY with the HDS, and enter the DATA LIST.

- 2. Check the ON/OFF information of the DRIVER'S REAR DOOR LOCK KNOB SWITCH (UNLOCK) in the DATA LIST.

Is information indicator ON?

YES

Go to step 27.

NO

Go to step 29.
27.Determine possible failure area (left rear door latch, others):
- 1. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

- 2. Disconnect the following connector.

Left rear door latch 10P connector

- 3. Check the ON/OFF information of the DRIVER'S REAR DOOR LOCK KNOB SWITCH (UNLOCK) in the DATA LIST.

Is information indicator OFF?

YES

Faulty left rear door lock knob switch, replace the left rear door latch .

NO

Go to step 28.

28.Shorted wire check (RR_L_SILCON_UNLOCK line):

- 1. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

- 2. Disconnect the following connector.

Under-dash fuse/relay box connector W (24P)

- 3. Check for continuity between test points 1 and 2.

Test condition	IG LOCK (0) or OFF mode Left rear door latch 10P connector: disconnected Under-dash fuse/relay box connector W (24P): disconnected
Test circuit	RR_L_SILCON_UNLOCK
Test point 1	Under-dash fuse/relay box connector W (24P) No. 4 (PNK)
Test point 2	Body ground

Courtesy of HONDA, U.S.A., INC.

Is there continuity?

YES

Repair a short to ground in the wire.

29.Keyless/power door locks/security system check 2:

- 1. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

- 2. Disconnect the following connector.

Left rear door latch 10P connector

- 3. Connect test points 1 and 2 with a jumper wire.

Test point 1	Left rear door latch 10P connector No. 9 (BRN)
Test point 2	Body ground

Courtesy of HONDA, U.S.A., INC.

- 4. Check the ON/OFF information of the DRIVER'S REAR DOOR LOCK KNOB SWITCH (UNLOCK) in the DATA LIST.

Is information indicator ON?

YES

Go to step 30.

Go to step 31.

30.Open wire check (GND line):

- 1. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

- 2. Check for continuity between test points 1 and 2.

Test condition	IG LOCK (0) or OFF mode Left rear door latch 10P connector: disconnected
Test circuit	GND
Test point 1	Left rear door latch 10P connector No. 6 (BLK)
Test point 2	Body ground

Courtesy of HONDA, U.S.A., INC.

Is there continuity?

YES

Faulty left rear door lock knob switch, replace the left rear door latch .

Repair an open or high resistance in the ground wire or poor ground (G602).

31.Open wire check (RR_L_SILCON_UNLOCK line):

- 1. Connect test points 1 and 2 with a jumper wire.

Test point 1	Under-dash fuse/relay box connector W (24P) No. 4 (PNK)
Test point 2	Body ground

Courtesy of HONDA, U.S.A., INC.

- 2. Check the ON/OFF information of the DRIVER'S REAR DOOR LOCK KNOB SWITCH (UNLOCK) in the DATA LIST.

Is information indicator ON?

YES

Repair an open or high resistance in the wire.

32.Keyless/power door locks/security system check 1:
- 1. With the right rear door lock knob switch in LOCK position, select SECURITY with the HDS, and enter the DATA LIST.

- 2. Check the ON/OFF information of the PASSENGER'S REAR DOOR LOCK KNOB SWITCH (UNLOCK) in the DATA LIST.

Is information indicator ON?

YES

Go to step 33.

NO

Go to step 35.
33.Determine possible failure area (right rear door latch, others):
- 1. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

- 2. Disconnect the following connector.

Right rear door latch 10P connector

- 3. Check the ON/OFF information of the PASSENGER'S REAR DOOR LOCK KNOB SWITCH (UNLOCK) in the DATA LIST.

Is information indicator OFF?

YES

Faulty right rear door lock knob switch, replace the right rear door latch .

NO

Go to step 34.

34.Shorted wire check (RR_R_SILCON_UNLOCK line):

- 1. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

- 2. Disconnect the following connector.

Under-dash fuse/relay box connector W (24P)

- 3. Check for continuity between test points 1 and 2.

Test condition	IG LOCK (0) or OFF mode Right rear door latch 10P connector: disconnected Under-dash fuse/relay box connector W (24P): disconnected
Test circuit	RR_R_SILCON_UNLOCK
Test point 1	Under-dash fuse/relay box connector W (24P) No. 5 (BRN)
Test point 2	Body ground

Courtesy of HONDA, U.S.A., INC.

Is there continuity?

YES

Repair a short to ground in the wire.

35.Keyless/power door locks/security system check 2:

- 1. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

- 2. Disconnect the following connector.

Right rear door latch 10P connector

- 3. Connect test points 1 and 2 with a jumper wire.

Test point 1	Right rear door latch 10P connector No. 6 (BRN)
Test point 2	Body ground

Courtesy of HONDA, U.S.A., INC.

- 4. Check the ON/OFF information of the PASSENGER'S REAR DOOR LOCK KNOB SWITCH (UNLOCK) in the DATA LIST.

Is information indicator ON?

YES

Go to step 36.

Go to step 37.

36.Open wire check (GND line):

- 1. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

- 2. Check for continuity between test points 1 and 2.

Test condition	IG LOCK (0) or OFF mode Right rear door latch 10P connector: disconnected
Test circuit	GND
Test point 1	Right rear door latch 10P connector No. 9 (BLK)
Test point 2	Body ground

Courtesy of HONDA, U.S.A., INC.

Is there continuity?

YES

Faulty right rear door lock knob switch, replace the right rear door latch .

Repair an open or high resistance in the ground wire or poor ground (G602).

37.Open wire check (RR_R_SILCON_UNLOCK line):

- 1. Connect test points 1 and 2 with a jumper wire.

Test point 1	Under-dash fuse/relay box connector W (24P) No. 5 (BRN)
Test point 2	Body ground

Courtesy of HONDA, U.S.A., INC.

- 2. Check the ON/OFF information of the PASSENGER'S REAR DOOR LOCK KNOB SWITCH (UNLOCK) in the DATA LIST.

Is information indicator ON?

YES

Repair an open or high resistance in the wire.

38.Keyless/power door locks/security system check:
- 1. With the driver's door closed, select SECURITY with the HDS, and enter the DATA LIST.

- 2. Check the ON/OFF information of the DRIVER'S DOOR SWITCH in the DATA LIST.

Is information indicator ON?

YES

Go to step 39.

NO

Go to step 41.

39.Driver's door switch operation check:

- 1. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

- 2. Remove the driver's door switch.

- 3. Disconnect the following connector.

Driver's door switch 1P connector

- 4. Check for continuity between test points 1 and 2.

Test point 1	Driver's door switch 1P connector
Test point 2	Switch ground

Courtesy of HONDA, U.S.A., INC.

Is there no continuity when you push the switch and is there continuity when you release the switch?

YES

Go to step 40.

Replace the driver's door switch.

40.Shorted wire check (FL_DOOR_SW line):

- 1. Disconnect the following connector.

Under-dash fuse/relay box connector B (44P)

- 2. Check for continuity between test points 1 and 2.

Test condition	IG LOCK (0) or OFF mode Driver's door switch 1P connector: disconnected Under-dash fuse/relay box connector B (44P): disconnected
Test circuit	FL_DOOR_SW
Test point 1	Under-dash fuse/relay box connector B (44P) No. 40 (GRN)
Test point 2	Body ground

Courtesy of HONDA, U.S.A., INC.

Is there continuity?

YES

Repair a short to ground in the wire.

41.Driver's door switch operation check:

- 1. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

- 2. Remove the driver's door switch.

- 3. Disconnect the following connector.

Driver's door switch 1P connector

- 4. Check for continuity between test points 1 and 2.

Test point 1	Driver's door switch 1P connector
Test point 2	Switch ground

Courtesy of HONDA, U.S.A., INC.

Is there no continuity when you push the switch and is there continuity when you release the switch?

YES

Go to step 42.

Replace the driver's door switch.

42.Open wire check (FL_DOOR_SW line):

- 1. Connect test points 1 and 2 with a jumper wire.

Test point 1	Under-dash fuse/relay box connector B (44P) No. 40 (GRN)
Test point 2	Body ground

Courtesy of HONDA, U.S.A., INC.

- 2. Check the ON/OFF information of the DRIVER'S DOOR SWITCH in the DATA LIST.

Is information indicator ON?

YES

Repair an open or high resistance in the wire.

43.Keyless/power door locks/security system check:
- 1. With the front passenger's door closed, select SECURITY with the HDS, and enter the DATA LIST.

- 2. Check the ON/OFF information of the FRONT PASSENGER'S DOOR SWITCH in the DATA LIST.

Is information indicator ON?

YES

Go to step 44.

NO

Go to step 46.

44.Front passenger's door switch operation check:

- 1. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

- 2. Remove the front passenger's door switch.

- 3. Disconnect the following connector.

Front passenger's door switch 1P connector

- 4. Check for continuity between test points 1 and 2.

Test point 1	Front passenger's door switch 1P connector
Test point 2	Switch ground

Courtesy of HONDA, U.S.A., INC.

Is there no continuity when you push the switch and is there continuity when you release the switch?

YES

Go to step 45.

Replace the front passenger's door switch.

45.Shorted wire check (FR_DOOR_SW line):

- 1. Disconnect the following connector.

Under-dash fuse/relay box connector B (44P)

- 2. Check for continuity between test points 1 and 2.

Test condition	IG LOCK (0) or OFF mode Front passenger's door switch 1P connector: disconnected Under-dash fuse/relay box connector B (44P): disconnected
Test circuit	FR_DOOR_SW
Test point 1	Under-dash fuse/relay box connector B (44P) No. 29 (LT GRN)
Test point 2	Body ground

Courtesy of HONDA, U.S.A., INC.

Is there continuity?

YES

Repair a short to ground in the wire.

46.Front passenger's door switch operation check:

- 1. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

- 2. Remove the front passenger's door switch.

- 3. Disconnect the following connector.

Front passenger's door switch 1P connector

- 4. Check for continuity between test points 1 and 2.

Test point 1	Front passenger's door switch 1P connector
Test point 2	Switch ground

Courtesy of HONDA, U.S.A., INC.

Is there no continuity when you push the switch and is there continuity when you release the switch?

YES

Go to step 47.

Replace the front passenger's door switch.

47.Open wire check (FR_DOOR_SW line):

- 1. Connect test points 1 and 2 with a jumper wire.

Test point 1	Under-dash fuse/relay box connector B (44P) No. 29 (LT GRN)
Test point 2	Body ground

Courtesy of HONDA, U.S.A., INC.

- 2. Check the ON/OFF information of the FRONT PASSENGER'S DOOR SWITCH in the DATA LIST.

Is information indicator ON?

YES

Repair an open or high resistance in the wire.

48.Keyless/power door locks/security system check:
- 1. With the front passenger's door closed, select SECURITY with the HDS, and enter the DATA LIST.

- 2. Check the ON/OFF information of the DRIVER'S REAR DOOR SWITCH in the DATA LIST.

Is information indicator ON?

YES

Go to step 49.

NO

Go to step 51.

49.Left rear door switch operation check:

- 1. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

- 2. Remove the left rear door switch.

- 3. Disconnect the following connector.

Left rear door switch 1P connector

- 4. Check for continuity between test points 1 and 2.

Test point 1	Left rear door switch 1P connector
Test point 2	Switch ground

Courtesy of HONDA, U.S.A., INC.

Is there no continuity when you push the switch and is there continuity when you release the switch?

YES

Go to step 50.

Replace the left rear door switch.

50.Shorted wire check (RL_DOOR_SW line):

- 1. Disconnect the following connector.

Under-dash fuse/relay box connector B (44P)

- 2. Check for continuity between test points 1 and 2.

Test condition	IG LOCK (0) or OFF mode Left rear door switch 1P connector: disconnected Under-dash fuse/relay box connector B (44P): disconnected
Test circuit	RL_DOOR_SW
Test point 1	Under-dash fuse/relay box connector B (44P) No. 33 (BRN)
Test point 2	Body ground

Courtesy of HONDA, U.S.A., INC.

Is there continuity?

YES

Repair a short to ground in the wire.

51.Left rear door switch operation check:

- 1. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

- 2. Remove the left rear door switch.

- 3. Disconnect the following connector.

Left rear door switch 1P connector

- 4. Check for continuity between test points 1 and 2.

Test point 1	Left rear door switch 1P connector
Test point 2	Switch ground

Courtesy of HONDA, U.S.A., INC.

Is there no continuity when you push the switch and is there continuity when you release the switch?

YES

Go to step 52.

Replace the left rear door switch.

52.Open wire check (RL_DOOR_SW line):

- 1. Connect test points 1 and 2 with a jumper wire.

Test point 1	Under-dash fuse/relay box connector B (44P) No. 33 (BRN)
Test point 2	Body ground

Courtesy of HONDA, U.S.A., INC.

- 2. Check the ON/OFF information of the DRIVER'S REAR DOOR SWITCH in the DATA LIST.

Is information indicator ON?

YES

Repair an open or high resistance in the wire.

53.Keyless/power door locks/security system check:
- 1. With the front passenger's door closed, select SECURITY with the HDS, and enter the DATA LIST.

- 2. Check the ON/OFF information of the PASSENGER'S REAR DOOR SWITCH in the DATA LIST.

Is information indicator ON?

YES

Go to step 54.

NO

Go to step 56.

54.Right rear door switch operation check:

- 1. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

- 2. Remove the right rear door switch.

- 3. Disconnect the following connector.

Right rear door switch 1P connector

- 4. Check for continuity between test points 1 and 2.

Test point 1	Right rear door switch 1P connector
Test point 2	Switch ground

Courtesy of HONDA, U.S.A., INC.

Is there no continuity when you push the switch and is there continuity when you release the switch?

YES

Go to step 55.

Replace the right rear door switch.

55.Shorted wire check (RR_DOOR_SW line):

- 1. Disconnect the following connector.

Under-dash fuse/relay box connector B (44P)

- 2. Check for continuity between test points 1 and 2.

Test condition	IG LOCK (0) or OFF mode Right rear door switch 1P connector: disconnected Under-dash fuse/relay box connector B (44P): disconnected
Test circuit	RR_DOOR_SW
Test point 1	Under-dash fuse/relay box connector B (44P) No. 34 (GRY)
Test point 2	Body ground

Courtesy of HONDA, U.S.A., INC.

Is there continuity?

YES

Repair a short to ground in the wire.

56.Right rear door switch operation check:

- 1. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

- 2. Remove the right rear door switch.

- 3. Disconnect the following connector.

Right rear door switch 1P connector

- 4. Check for continuity between test points 1 and 2.

Test point 1	Right rear door switch 1P connector
Test point 2	Switch ground

Courtesy of HONDA, U.S.A., INC.

Is there no continuity when you push the switch and is there continuity when you release the switch?

YES

Go to step 57.

Replace the right rear door switch.

57.Open wire check (RR_DOOR_SW line):

- 1. Connect test points 1 and 2 with a jumper wire.

Test point 1	Under-dash fuse/relay box connector B (44P) No. 34 (GRY)
Test point 2	Body ground

Courtesy of HONDA, U.S.A., INC.

- 2. Check the ON/OFF information of the PASSENGER'S REAR DOOR SWITCH in the DATA LIST.

Is information indicator ON?

YES

Repair an open or high resistance in the wire.

58.Keyless/power door locks/security system check:

- 1. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

- 2. Disconnect the following connector.

Driver's door latch 10P connector

- 3. Connect test points 1 and 2 with a jumper wire.

Test point 1	Driver's door latch 10P connector No. 9 (PNK)
Test point 2	Body ground

Courtesy of HONDA, U.S.A., INC.

- 4. Select SECURITY with the HDS, and enter the DATA LIST.

- 5. Check the ON/OFF information of the DRIVER'S DOOR KEY CYLINDER SWITCH (LOCK) in the DATA LIST.

Is information indicator ON?

YES

Go to step 59.

Go to step 61.

59.Driver's door key cylinder switch operation check:
- 1. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

- 2. Test the driver's door key cylinder switch .

Is the switch OK?

YES

Go to step 60.

NO

Faulty driver's door key cylinder switch, replace the driver's door latch .

60.Open wire check (GND line):

- 1. Check for continuity between test points 1 and 2.

Test condition	IG LOCK (0) or OFF mode Driver's door latch 10P connector: disconnected
Test circuit	GND
Test point 1	Driver's door latch 10P connector No. 7 (BLK)
Test point 2	Body ground

Courtesy of HONDA, U.S.A., INC.

Is there continuity?

YES

Repair an open or high resistance in the ground wire or poor ground (G502).

61.Open wire check (DR_KEY_CYL_LOCK line):

- 1. Connect test points 1 and 2 with a jumper wire.

Test point 1	Under-dash fuse/relay box connector X (10P) No. 10 (PNK)
Test point 2	Body ground

Courtesy of HONDA, U.S.A., INC.

- 2. Check the ON/OFF information of the DRIVER'S DOOR KEY CYLINDER SWITCH (LOCK) in the DATA LIST.

Is information indicator ON?

YES

Repair an open or high resistance in the wire.