| Cruise control cannot be set |
- Check the No. 24 (10 A) fuse in the under-dash fuse/relay box.
- Do CRUISE CONTROL COMBINATION SWITCH TEST
.
- Do CRUISE CONTROL INPUT TEST
.
- Check for PGM-FI DTCs (see GENERAL TROUBLESHOOTING INFORMATION
).
|
- Poor ground G101 (A/T model) or G401 (M/T model)
|
| Cruise control can be set, but the cruise main indicator does not come on |
- Do the gauge control module self-diagnostic function procedure (see SELF-DIAGNOSTIC FUNCTION
).
- Do CRUISE CONTROL INPUT TEST
. Test the cruise control main switch signal input.
- Check for PGM-FI DTCs (see GENERAL TROUBLESHOOTING INFORMATION
).
|
Faulty gauge control module |
| Cruise control can be set, but the cruise control indicator does not come on |
- Do the gauge control module self-diagnostic function procedure (see SELF-DIAGNOSTIC FUNCTION
).
- Do CRUISE CONTROL INPUT TEST
). Test the cruise control indicator signal input.
- Check for PGM-FI DTCs (see GENERAL TROUBLESHOOTING INFORMATION
).
|
Faulty gauge control module |
| Vehicle does not accelerate accordingly when the resume/accel button is pressed |
- Do CRUISE CONTROL COMBINATION SWITCH TEST
.
- Do CRUISE CONTROL INPUT TEST
. Test the cruise control resume/accel switch signal input.
- Check for PGM-FI DTCs (see GENERAL TROUBLESHOOTING INFORMATION
).
|
Open circuit, loose or disconnected terminals: LT GRN/BLK, or BLU wire |
| Set speed does not cancel when the brake pedal is pressed |
- Do the brake pedal position switch test (see HIGH MOUNT BRAKE LIGHT REPLACEMENT
).
- Do CRUISE CONTROL INPUT TEST
. Test the brake pedal position switch signal input.
- Check for PGM-FI DTCs (see GENERAL TROUBLESHOOTING INFORMATION
).
|
- Short to power on the BRN wire
- Faulty brake pedal position switch
|
| Set speed does not cancel (engine rpm stays high) when the clutch pedal is pressed (M/T model) |
- Do CLUTCH PEDAL POSITION SWITCH TEST
.
- Do CRUISE CONTROL INPUT TEST
. Test the clutch pedal position switch signal input.
- Check for PGM-FI DTCs (see GENERAL TROUBLESHOOTING INFORMATION
).
|
- Short to ground on the PUR wire
- Faulty clutch pedal position switch
|
| Set speed does not cancel when the cruise control main button is pressed |
- Do CRUISE CONTROL COMBINATION SWITCH TEST
.
- Do CRUISE CONTROL INPUT TEST
. Test the cruise control main switch signal input.
- Check for PGM-FI DTCs (see GENERAL TROUBLESHOOTING INFORMATION
).
|
Short to power on the PNK, or LT GRN wire |
| Set speed does not cancel when the cancel button is pressed |
- Do CRUISE CONTROL COMBINATION SWITCH TEST
.
- Do CRUISE CONTROL INPUT TEST
. Test the cruise control cancel switch signal input.
- Check for PGM-FI DTCs (see GENERAL TROUBLESHOOTING INFORMATION
).
|
Open circuit, loose or disconnected terminals: YEL/RED, RED or LT GRN/BLK, BLU wire |
| Set speed does not resume when the resume/accel button is pressed (with the cruise control main switch turned on, and set speed temporarily canceled by pressing the brake pedal) |
- Do CRUISE CONTROL COMBINATION SWITCH TEST
).
- Do CRUISE CONTROL INPUT TEST
). Test the cruise control resume/accel switch signal input.
- Check for PGM-FI DTCs (see GENERAL TROUBLESHOOTING INFORMATION
).
|
Open circuit, loose or disconnected terminals: LT GRN/BLK, or BLU wire |
| Set speed does not resume when the resume/accel button is pressed (with the cruise control main switch turned on, and set speed temporarily canceled by pressing the clutch pedal) (M/T model) |
- Do CRUISE CONTROL COMBINATION SWITCH TEST
.
- Do CRUISE CONTROL INPUT TEST
. Test the cruise control resume/accel switch signal input.
- Check for PGM-FI DTCs (see GENERAL TROUBLESHOOTING INFORMATION
).
|
Open circuit, loose or disconnected terminals: LT GRN/BLK, or BLU wire |
| Light switch turned on, the cruise control combination switch illumination does not come on |
- Check the No. 29 (10 A) fuse in the under-dash fuse/relay box
- Do CRUISE CONTROL COMBINATION SWITCH TEST
). Test the cruise control resume/accel switch signal input..
|
Open circuit, loose or disconnected terminals: GRY, RED/BLK, GRN, and RED wire |