Specifications Index

COMMON SPECS & PROCEDURES INDEX

System		Specification/Procedure
Air Conditioning
Service		HVAC SERVICE SPECIFICATIONS (EXCEPT TYPE-R/SI) , HVAC SERVICE SPECIFICATIONS (TYPE-R/SI)
Torque		TORQUE SPECIFICATIONS
Axle Nut/Hub Nut
2.0L		181 N.m (133 lbf.ft)
	1.5L	245 N.m (181 lbf.ft)
Battery		12 VOLT BATTERY REMOVAL AND INSTALLATION (EXCEPT TYPE-R) , 12 VOLT BATTERY REMOVAL AND INSTALLATION (TYPE-R)
Brakes
Bleeding Sequence		CONVENTIONAL BRAKE SYSTEM BLEEDING (EXCEPT TYPE-R) , CONVENTIONAL BRAKE SYSTEM BLEEDING (TYPE-R)
Disc Brakes		BRAKE SERVICE SPECIFICATIONS (EXCEPT TYPE-R/SI) , BRAKE SERVICE SPECIFICATIONS (TYPE-R/SI)
Torque		TORQUE SPECIFICATIONS
Charging
Service Specifications		ENGINE ELECTRICAL SERVICE SPECIFICATIONS (EXCEPT TYPE-R/SI) or ENGINE ELECTRICAL SERVICE SPECIFICATIONS (TYPE-R/SI)
Torque		TORQUE SPECIFICATIONS
Drive Belts
Belt Routing & Adjustment		DRIVE BELT REMOVAL AND INSTALLATION
Engine Cooling
General Service Specifications		ENGINE COOLING SERVICE SPECIFICATIONS (EXCEPT TYPE-R/SI) , ENGINE COOLING SERVICE SPECIFICATIONS (TYPE-R/SI)
Radiator Cap Pressure		1.5L, K20C2 93-123 kPa (0.95-1.25 kgf/cm2, 13.5-17.8 psi) K20C1 (2017 2018 2019 2020 2021) 112-146 kPa (1.14-1.49 kgf/cm 2, 16.2-21.2 psi)
Thermostat R & I		THERMOSTAT REMOVAL, INSTALLATION, AND TEST (1.5L ENGINE) , THERMOSTAT REMOVAL, INSTALLATION, AND TEST (K20C1) , THERMOSTAT REMOVAL, INSTALLATION, AND TEST (K20C2)
Water Pump R & I		WATER PUMP REMOVAL AND INSTALLATION (K20C1) ,WATER PUMP REMOVAL AND INSTALLATION (K20C2) ,WATER PUMP REMOVAL AND INSTALLATION (1.5L ENGINE)
Engine Mechanical
Compression		1.5L 980 kPa (9.99 kgf/cm² , 142.1 psi) Minimum 200 kPa (2.04 kgf/cm² , 29.0 psi) Maximum variation K20C1, K20C2 930 kPa (9.48 kgf/cm² , 134.8 psi) Minimum 200 kPa (2.04 kgf/cm² , 29.0 psi) Maximum variation
1.5L, K20C2 Oil Pressure (176°F (80°C)		90 kPa (0.92 kgf/cm² , 13.1 psi) min. @ idle 280 kPa (2.86 kgf/cm² , 40.6 psi) min. @ 3000 RPM
K20C1 Oil Pressure (176°F (80°C)		100 kPa (1.02 kgf/cm² , 14.5 psi) min. @ idle 400 kPa (4.08 kgf/cm² , 58.0 psi) min. @ 3000 RPM
Overhaul		See applicable specifications tables in ENGINE SERVICE SPECIFICATIONS (EXCEPT TYPE-R/SI) , ENGINE SERVICE SPECIFICATIONS (TYPE-R/SI)
Torque		TORQUE SPECIFICATIONS
Fluid Specifications		See FLUIDS under MAINTENANCE tab.
Flywheel/Flex Plate Torque		74 N.m (55 ft. lbs.)
Fuel System
Pressure Specification		1.5L, K20C2 390-440 kPa (3.98-4.49 kgf/cm² , 56.6-63.8 psi) K20C1 500-550 kPa (5.1-5.61 kgf/cm² , 72.5-79.8 psi)
Fuel Pressure Test Procedure		FUEL PRESSURE TEST (K20C2, 1.5L) , FUEL PRESSURE TEST (K20C1)
Ignition
Firing Order & Cylinder Identification		FIRING ORDER & CYLINDER IDENTIFICATION
Spark Plug NGK: 7751
Gap		1.5L, K20C1 0.70-0.75 mm (0.0276-0.0295 in) K20C2 1.0-1.1 mm (0.039-0.043 in)
Torque		22 N.m (16 ft. lbs.)
Starting
Starter		ENGINE ELECTRICAL SERVICE SPECIFICATIONS (EXCEPT TYPE-R/SI) or ENGINE ELECTRICAL SERVICE SPECIFICATIONS (TYPE-R/SI)
Torque		TORQUE SPECIFICATIONS
Wheel Alignment
Adjustment Specifications		SUSPENSION SERVICE SPECIFICATIONS (EXCEPT TYPE-R/SI) , SUSPENSION SERVICE SPECIFICATIONS (TYPE-R/SI)
	Torque	TORQUE SPECIFICATIONS
Wheel & Tire
Wheel Lug Nut Torque		108 N.m (80 ft. lbs.)