Keyless Access System Touch Sensor Circuit Troubleshooting: Inspection

VOUT_FR_DR, TS_FR_DR, DL_FR_DR, GND Circuit Inspection 

Test Procedure 

• Preparation
  1. -

     Driver's door outer handle connector (8P): disconnected

  2. -

     Body control module connector C (66P): disconnected

• Procedure
  1. -

     Perform the inspection according to the following chart.

			(Disconnected) Driver's door outer handle connector (8P) female terminals	(Disconnected)Body control module connector C (66P) female terminals
		IG Mode	Courtesy of HONDA, U.S.A., INC.	Courtesy of HONDA, U.S.A., INC.	Normal Conditions
	VOUT_FR_DR open wire inspection	OFF			There is less than 1 Ohm
	TS_FR_DR open wire inspection	OFF			There is less than 1 Ohm
	DL_FR_DR open wire inspection	OFF			There is less than 1 Ohm
	GND open wire inspection	OFF			There is less than 1 Ohm
	Refer to the Open/Shorted Wire Inspection Description for the method to inspect the shorted circuit below, then start to inspect according to circumstances.
	VOUT_FR_DR shorted to ground inspection	OFF			There is more than 1 MOhm
	TS_FR_DR shorted to ground inspection	OFF			There is more than 1 MOhm
	DL_FR_DR shorted to ground inspection	OFF			There is more than 1 MOhm

Results 

• If it is abnormal, there is a problem in the circuit.

VOUT_FR_AS, TS_FR_AS, DL_FR_AS, GND Circuit Inspection 

Test Procedure 

• Preparation
  1. -

     Front passenger's door outer handle connector (8P): disconnected

  2. -

     Body control module connector C (66P): disconnected

• Procedure
  1. -

     Perform the inspection according to the following chart.

			(Disconnected) Front passenger's door outer handle connector (8P) female terminals	(Disconnected) Body control module connector C (66P) female terminals
		IG Mode	Courtesy of HONDA, U.S.A., INC.	Courtesy of HONDA, U.S.A., INC.	Normal Conditions
	VOUT_FR_AS open wire inspection	OFF			There is less than 1 Ohm
	TS_FR_AS open wire inspection	OFF			There is less than 1 Ohm
	DL_FR_AS open wire inspection	OFF			There is less than 1 Ohm
	GND open wire inspection	OFF			There is less than 1 Ohm
	Refer to the Open/Shorted Wire Inspection Description for the method to inspect the shorted circuit below, then start to inspect according to circumstances.
	VOUT_FR_AS shorted to ground inspection	OFF			There is more than 1 MOhm
	TS_FR_AS shorted to ground inspection	OFF			There is more than 1 MOhm
	DL_FR_AS shorted to ground inspection	OFF			There is more than 1 MOhm

Results 

• If it is abnormal, there is a problem in the circuit.

Driver's Door Outer Handle Inspection 

Test Procedure 

• Install a known-good driver's door outer handle and attempt to reproduce the failure.

Results 

• If the failure is reproduced, there is a problem with other related components.
• If the symptom/DTC goes away, the driver's door outer handle must be faulty.

Front Passenger's Door Outer Handle Inspection 

Test Procedure 

• Install a known-good front passenger's door outer handle and attempt to reproduce the failure.

Results 

• If the failure is reproduced, there is a problem with other related components.
• If the symptom/DTC goes away, the front passenger's door outer handle must be faulty.

Body Control Module Inspection 

Test Procedure 

• If the other inspection item(s) indicated a normal condition, then it is determined that the remaining body control module is the cause.

Results 

• There is a problem with the body control module.