Keyless Access System Symptom Troubleshooting - Cannot select ON mode with keyless access and with the keyless remote touching the engine start/stop switch: Inspection

+B_SMART, SS1(+), SS2(-), GND Circuit Inspection 

Test Procedure 

• Preparation
  • Engine start/stop switch connector (10P): disconnected
  • Body control module connector C (66P): disconnected
• Procedure
  • Perform the inspection according to the following chart.

			(Disconnected) Engine start/stop switch connector (10P) female terminals	(Disconnected) Body control module connector C (66P) female terminals
		IG Mode	Courtesy of HONDA, U.S.A., INC.	Courtesy of HONDA, U.S.A., INC.	Normal Conditions
	+B_SMART circuit inspection	OFF			12 V battery voltage [circuit type 1]
	SS1(+) open wire inspection	OFF			There is less than 1 Ohms
	SS2(-) open wire inspection	OFF			There is less than 1 Ohms
	GND open wire inspection	OFF			There is less than 1 Ohms

Results 

• If abnormal, there is a problem in the circuit.

  If the power supply inspection of the above table showed abnormally, do the additional Power Supply Inspection , to locate the failure.

+B_BACK_UP, +B_SMART, GND, PGND, PGND Circuit Inspection 

Test Procedure 

• Preparation
  • Body control module connector A (66P): disconnected
  • Body control module connector B (66P): disconnected
• Procedure
  • Perform the inspection according to the following chart.

			(Disconnected) Body control module connector A (66P) female terminals

		IG Mode	Courtesy of HONDA, U.S.A., INC.	Normal Conditions
	+B_BACK_UP circuit inspection	OFF		12 V battery voltage[circuit type 1]
	+B_SMART circuit inspection	OFF		12 V battery voltage[circuit type 1]
	GND open wire inspection	OFF		There is less than 1 Ohms

			(Disconnected) Body control module connector B (66P) female terminals
		IG Mode	Courtesy of HONDA, U.S.A., INC.	Normal Conditions
	PGND open wire inspection	OFF		There is less than 1 Ohms
	PGND open wire inspection	OFF		There is less than 1 Ohms

Results 

• If abnormal, there is a problem in the circuit.

  If the power supply inspection of the above table showed abnormally, do the additional Power Supply Inspection , to locate the failure.

ESL_PWR [TCUWUP/ACC], IGN_TRX [IGNTRx] Circuit Inspection 

Test Procedure 

• Preparation
  • TCM connector A (23P): disconnected
  • Body control module connector C (66P): disconnected
• Procedure
  • Perform the inspection according to the following chart.

			(Disconnected) TCM connector A (23P) female terminals	(Disconnected) Body control module connector C (66P) female terminals
		IG Mode	Courtesy of HONDA, U.S.A., INC.	Courtesy of HONDA, U.S.A., INC.	Normal Conditions
	ESL_PWR [TCUWUP/ACC] open wire inspection	OFF			There is less than 1 Ohms
	IGN_TRX [IGNTRx] open wire inspection	OFF			There is less than 1 Ohms
	Refer to the Open/Shorted Wire Inspection Description for the method to inspect the shorted circuit below, then start to inspect according to circumstances.
	ESL_PWR [TCUWUP/ACC] shorted to ground inspection	OFF			There is more than 1 MOhms
	IGN_TRX [IGNTRx] shorted to ground inspection	OFF			There is more than 1 MOhms

Results 

• If abnormal, there is a problem in the circuit.

L-LINE Circuit Inspection 

NOTICE:  

Before disconnecting the SRS unit connector, do the 12 volt battery terminal disconnection procedure and wait for at least 3 minutes.

Test Procedure 

• Preparation
  • Body control module connector A (66P): disconnected
  • SRS unit connector A (43P) : disconnected
• Procedure
  • Perform the inspection according to the following chart.

			(Disconnected) Data link connector (DLC) (16P) female terminals	(Disconnected) Body control module connector A (66P) female terminals
		IG Mode	Courtesy of HONDA, U.S.A., INC.	Courtesy of HONDA, U.S.A., INC.	Normal Conditions
	L-LINE open wire inspection	OFF			There is less than 1 Ohms
	Refer to the Open/Shorted Wire Inspection Description for the method to inspect the shorted circuit below, then start to inspect according to circumstances.
	L-LINE shorted to ground inspection	OFF			There is more than 1 MOhms

Results 

• If abnormal, there is a problem in the circuit.

Body Control Module Inspection 

NOTE:  Since there is no direct method to test the inspection item, troubleshooting is performed using a known-good component.

Test Procedure 

• Install a known-good body control module and attempt to reproduce the failure.

Results 

• If the failure is reproduced, there is a problem with other related components.
• If the symptom/DTC goes away, the body control module must be faulty.

TCM Inspection 

Test Procedure 

• If the other inspection item(s) indicated a normal condition, then it is determined that the remaining TCM is the cause.

Results 

• There is a problem with the TCM.