Repair Procedure

WARNING:

SRS components are located in this area. Before doing repairs or service:
- Review the SRS component locations .
- Review the precautions and procedures .

NOTICE:

Special Mag-Form® self-tapping bolts are used to attach components to the steering hanger beam. If a Mag-Form® bolt hole is stripped, oversize bolts are available.

Fig 1: Dashboard/Steering Hanger Beam Area Replacement Components With Torque Specifications (1 Of 12)

Courtesy of HONDA, U.S.A., INC.

: Torque, Nm (lbfft)

: Replace

: Warning/Caution

: Inspection/Adjustment

*: Learning

■: SPL Tool

: Required Removal

*1: If a Mag-Form® bolt hole is stripped, oversize bolts are available.
*2: With color audio type
*3: With display audio type
*4: With glove box damper

Fig 2: Dashboard/Steering Hanger Beam Area Replacement Components (2 Of 12)

Courtesy of HONDA, U.S.A., INC.

: Torque, Nm (lbfft)

: Replace

: Warning/Caution

: Inspection/Adjustment

*: Learning

■: SPL Tool

: Required Removal

*1:For some models

Fig 3: Dashboard/Steering Hanger Beam Area Replacement Components (3 Of 12)

Courtesy of HONDA, U.S.A., INC.

: Torque, Nm (lbfft)

: Replace

: Warning/Caution

: Inspection/Adjustment

*: Learning

■: SPL Tool

: Required Removal

*1:With front passenger's tray light

Fig 4: Dashboard/Steering Hanger Beam Area Replacement Components (4 Of 12)

Courtesy of HONDA, U.S.A., INC.

: Torque, Nm (lbfft)

: Replace

: Warning/Caution

: Inspection/Adjustment

*: Learning

■: SPL Tool

: Required Removal

*1: Part(s) are shown for one side only as the procedure is the same for both sides.
*2: With front center speaker

Fig 5: Dashboard/Steering Hanger Beam Area Replacement Components (5 Of 12)

Courtesy of HONDA, U.S.A., INC.

: Torque, Nm (lbfft)

: Replace

: Warning/Caution

: Inspection/Adjustment

*: Learning

■: SPL Tool

: Required Removal

*1: With footwell light

Fig 6: Dashboard/Steering Hanger Beam Area Replacement Components With Torque Specifications (6 Of 12)

Courtesy of HONDA, U.S.A., INC.

: Torque, Nm (lbfft)

: Replace

: Warning/Caution

: Inspection/Adjustment

*: Learning

■: SPL Tool

: Required Removal

*1: With color audio type
*2: With display audio type

Fig 7: Dashboard/Steering Hanger Beam Area Replacement Components With Torque Specifications (7 Of 12)

Courtesy of HONDA, U.S.A., INC.

: Torque, Nm (lbfft)

: Replace

: Warning/Caution

: Inspection/Adjustment

*: Learning

■: SPL Tool

: Required Removal

*1: With head up display
*2: With multi view camera system
*3: If a Mag-Form® bolt hole is stripped, oversize bolts are available.

Fig 8: Dashboard/Steering Hanger Beam Area Replacement Components With Torque Specifications (8 Of 12)

Courtesy of HONDA, U.S.A., INC.

: Torque, Nm (lbfft)

: Replace

: Warning/Caution

: Inspection/Adjustment

*: Learning

■: SPL Tool

: Required Removal

*1: With display audio type
*2: With parking and back-up sensor control unit
*3: If a Mag-Form® bolt hole is stripped, oversize bolts are available.

Fig 9: Dashboard/Steering Hanger Beam Area Replacement Components With Torque Specifications (9 Of 12)

Courtesy of HONDA, U.S.A., INC.

: Torque, Nm (lbfft)

: Replace

: Warning/Caution

: Inspection/Adjustment

*: Learning

■: SPL Tool

: Required Removal

*1: With AC inverter unit
*2: With telematics control unit

Fig 10: Dashboard/Steering Hanger Beam Area Replacement Components With Torque Specifications (10 Of 12)

Courtesy of HONDA, U.S.A., INC.

: Torque, Nm (lbfft)

: Replace

: Warning/Caution

: Inspection/Adjustment

*: Learning

■: SPL Tool

: Required Removal

*1: With display audio type

Fig 11: Dashboard/Steering Hanger Beam Area Replacement Components With Torque Specifications (11 Of 12)

Courtesy of HONDA, U.S.A., INC.

: Torque, Nm (lbfft)

: Replace

: Warning/Caution

: Inspection/Adjustment

*: Learning

■: SPL Tool

: Required Removal

*1: With head up display
*2: If a Mag-Form® bolt hole is stripped, oversize bolts are available.

Fig 12: Dashboard/Steering Hanger Beam Area Replacement Components (12 Of 12)

Courtesy of HONDA, U.S.A., INC.

: Torque, Nm (lbfft)

: Replace

: Warning/Caution

: Inspection/Adjustment

*: Learning

■: SPL Tool

: Required Removal

A.-

Courtesy of HONDA, U.S.A., INC.
B.-

Courtesy of HONDA, U.S.A., INC.
C.-
Sub-Procedure

Removal
- Refer to the figure.
Courtesy of HONDA, U.S.A., INC.

After Installation
- Do the Self-Diagnostic Function with the HDS or the climate control unit .
D.-

Courtesy of HONDA, U.S.A., INC.
E.-

Courtesy of HONDA, U.S.A., INC.
F.-
Sub-Procedure

Removal
- Refer to the figure.
Courtesy of HONDA, U.S.A., INC.
G.-

Courtesy of HONDA, U.S.A., INC.
H.-

Courtesy of HONDA, U.S.A., INC.
I.-

Courtesy of HONDA, U.S.A., INC.
J.-
Sub-Procedure

Removal
- Gauge Control Module Rewriting - Refer to: Gauge Control Module Update () or Rewriting the ODO Data and Transferring the Service Reminder System Data to a New Gauge Control Module ()
  - If you are replacing the gauge control module, make sure to read the data off the old gauge control module.
After Installation
- After installing the gauge control module, perform the self-diagnostic function to check the operation of the indicators.
- Gauge Control Module Transfer
  - After replacing, write the ODO value data onto the new gauge control module, refer to transferring the ODO Data onto a New Gauge Control Module Procedure (Transferring) - Refer to: Gauge Control Module Update () or Rewriting the ODO Data and Transferring the Service Reminder System Data to a New Gauge Control Module () .
  - If the data transfer fails, refer to the instructions to release the locked ODO value - Refer to: Gauge Control Module Update () or Rewriting the ODO Data and Transferring the Service Reminder System Data to a New Gauge Control Module () .
- Gauge Control Module Update
  NOTE: If you replaced the gauge control module, do the gauge control module update procedure - Refer to: Gauge Control Module Update () or Rewriting the ODO Data and Transferring the Service Reminder System Data to a New Gauge Control Module () .
K.-

Courtesy of HONDA, U.S.A., INC.
L.-

Courtesy of HONDA, U.S.A., INC.
M.-

Courtesy of HONDA, U.S.A., INC.
N.-

Courtesy of HONDA, U.S.A., INC.
O.-

Courtesy of HONDA, U.S.A., INC.
P.-

Courtesy of HONDA, U.S.A., INC.
Q.-

Courtesy of HONDA, U.S.A., INC.
R.-
Sub-Procedure

Removal
- Refer to the figure 1 and 2.
Figure 1

Courtesy of HONDA, U.S.A., INC.

Figure 2

Courtesy of HONDA, U.S.A., INC.
S.-
Sub-Procedure

Removal
- Refer to the figure.
Courtesy of HONDA, U.S.A., INC.
T.-

Courtesy of HONDA, U.S.A., INC.
U.-

Courtesy of HONDA, U.S.A., INC.
V.-
Sub-Procedure

Courtesy of HONDA, U.S.A., INC.

Removal
- Refer to the figure.
After Installation
- Do the Self-Diagnostic Function with the HDS, the HVAC control unit, or the climate control unit .
W.-

Courtesy of HONDA, U.S.A., INC.
X.-
Sub-Procedure

Courtesy of HONDA, U.S.A., INC.

Removal
- Refer to the figure.
Remote Battery Specifications

Type

CR2032

After Installation
- When replacing the remote, do the keyless access system registration .
Y.-
NOTE: Position of the switch is different depending on the model.

Sub-Procedure

Courtesy of HONDA, U.S.A., INC.

Removal
- Refer to the figure.
Z.-
NOTE: Position of the switch is different depending on the model.

Sub-Procedure

Courtesy of HONDA, U.S.A., INC.

Removal
- Refer to the figure.
AA.-
NOTE: Position of the switch is different depending on the model.

Sub-Procedure

Courtesy of HONDA, U.S.A., INC.

Removal
- Refer to the figure.
AB.-
After Installation
- Do the Self-Diagnostic Function with the HDS, the HVAC control unit, or the climate control unit .
AC.-

Courtesy of HONDA, U.S.A., INC.
AD.-
Sub-Procedure

Courtesy of HONDA, U.S.A., INC.

Removal
- Refer to the figure.
AE.-
Sub-Procedure

Courtesy of HONDA, U.S.A., INC.

Removal
- Refer to the figure.
AF.-
Sub-Procedure

Courtesy of HONDA, U.S.A., INC.

Removal
- Refer to the figure.
AG.-
Sub-Procedure

Courtesy of HONDA, U.S.A., INC.

Removal
- Refer to the figure.
AH.-
Sub-Procedure

Courtesy of HONDA, U.S.A., INC.

Removal
- Refer to the figure.
AI.-
Sub-Procedure

Courtesy of HONDA, U.S.A., INC.

Removal
- Refer to the figure.
AJ.-
Sub-Procedure

Courtesy of HONDA, U.S.A., INC.

Removal
- Refer to the figure.
AK.-
Sub-Procedure

Courtesy of HONDA, U.S.A., INC.

Removal
- Refer to the figure.
AL.-
Key Information

Do the following before starting your work.

Remove:
- Dashboard
AM.-
WARNING:
- Review the precautions and procedures before doing repairs or service .
- Wait at least 3 minutes, after disconnecting the 12 volt battery terminal.
NOTICE:

If you are replacing the front passenger's airbag after a deployment, refer to Component Replacement/Inspection After Deployment - Refer to: Airbag and Tensioner Disposal () or SRS Component Replacement/Inspection After Deployment () for a complete list of other parts that must also be replaced.

Preconditions
- 12 Volt Battery Negative Terminal Disconnected
Key Information

Do the following before starting your work.

Remove:
- Globe Box
Sub-Procedure

Installation

NOTICE:
- Make sure there are no objects between the airbag and the dashboard.
- Make sure the airbag is fully seated, and make sure the dashboard is not deformed or damaged after the airbag is in place.
- Make sure the hooks are set properly.
- Do not install the airbag while it is in a plastic bag.
- Before installing the glove box back cover, make sure the SRS indicator works normally.
After Installation

1. 12 Volt Battery Negative Terminal Reconnect

2. SRS Operation Confirm
- Turn the vehicle to the ON mode, and check that the SRS indicator comes on for about 6 seconds and then goes off.
AN.-
Key Information

Do the following before starting your work.

Remove:
- Passenger's Dashboard Undercover
Sub-Procedure

Removal/Installation

NOTICE:
- Before replacing the multi view camera unit, retrieve the aiming data from the multi view camera unit with the HDS.
- If the data transfer fails, do the multi view camera aiming - Refer to: Multi View Camera Aiming () or Multi View Camera Picture Inspection () .
NOTE:
- Obtain a multi view camera unit before starting the rewriting process.
- Rewriting is not possible on a multi view camera unit that will not communicate with the HDS.
- Once you have started this procedure, you must complete it before removing the HDS from the DLC.
- Before you rewrite the multi view camera unit, make sure the battery in the vehicle is fully charged and connect a jumper to the battery (not a battery charger) to maintain system voltage.
1. Connect the HDS to the DLC .

2. Select the following menu buttons on the HDS screen in sequence.
1. DRIVING SUPPORT (System Selection Menu)
2. MULTI VIEW CAMERA SYSTEM
3. ADJUSTMENT
4. CAMERA AIMING DATA TRANSFER
3. Replace the multi view camera unit.

4. Follow the instructions on the display to write the new aiming data on the new multi view camera unit.

After Installation
- Multi View Camera Unit Update
AO.-
Key Information

Do the following before starting your work.

Remove:
- Driver's Lower Cover
Sub-Procedure

Courtesy of HONDA, U.S.A., INC.

Removal
- Refer to the figure.
After Installation
- CAN Gateway Update
  NOTE: When replacing the CAN gateway, do this procedure.
AP.-
WARNING:
- Review the precautions and procedures before doing repairs or service .
- Wait at least 3 minutes, after disconnecting the 12 volt battery terminal.
NOTICE:

If you are replacing the driver's knee airbag after a deployment, refer to Component Replacement/Inspection After Deployment - Refer to: Airbag and Tensioner Disposal () or SRS Component Replacement/Inspection After Deployment () for a complete list of other parts that must also be replaced.

Preconditions
- 12 Volt Battery Negative Terminal Disconnect
Key Information

Do the following before starting your work.

Remove:
- Driver's Dashboard Lower Cover
Sub-Procedure

Installation

NOTICE:

Before installing the driver's dashboard lower cover, make sure the SRS indicator works normally.

After Installation

1. 12 Volt Battery Negative Terminal Reconnect

2. Turn the vehicle to the ON mode, and check that the SRS indicator comes on for about 6 seconds and then goes off.
AQ.-
Preconditions
- 12 Volt Battery Negative Terminal Disconnected
Key Information

Do the following before starting your work.

Remove:
- Driver's Dashboard Lower Cover
Sub-Procedure

Removal
- Refer to the figure.
Courtesy of HONDA, U.S.A., INC.

After Installation

NOTE: When replacing the body control module, do this procedure.
- 12 Volt Battery Negative Terminal Reconnect
- Keyless Access System Registration
- Tire Pressure Sensor ID Memorization
- Body Control Module Update
- Wireless Seat Belt Reminder System Pairing.
AR.-
Key Information

Do the following before starting your work.

Remove:
- Passenger's Side Outlet
AS.-
Sub-Procedure

Courtesy of HONDA, U.S.A., INC.

Removal
- Refer to the figure.
After Installation

NOTE: If you are substituting a known-good parking and back-up sensor control unit, reset the parking and back-up sensor control unit - Refer to: Parking and Back-Up Sensor Control Unit Update () or Resetting the Parking and Back-Up Sensor Control Unit () .
AT.-
WARNING:
- Review the precautions and procedures before doing repairs or service .
- Wait at least 3 minutes, after disconnecting the 12 volt battery terminal.
Preconditions
- 12 Volt Battery Negative Terminal Disconnected
Key Information

Do the following before starting your work.

Remove:
- Driver's Dashboard Lower Cover
Sub-Procedure

Removal
- Carefully remove the relays using the relay puller tool.
  NOTE: Do not use pliers. Pliers will damage the relays, which could cause the engine to stall, not start, or cause other functions to fail.
Courtesy of HONDA, U.S.A., INC.

After Installation
- 12 Volt Battery Negative Terminal Reconnect
AU.-
Key Information

Do the following before starting your work.

Remove:
- Driver's Lower Cover
AV.-
Key Information

Do the following before starting your work.

Remove:
- Gauge Control Module
After Installation
- Keyless Access System Registration
- Telematics System Registration
AW.-
WARNING:
- Review the precautions and procedures before doing repairs or service .
- Wait at least 3 minutes, after disconnecting the 12 volt battery terminal.
NOTICE:

If you are replacing the front passenger's knee airbag after a deployment, refer to Component Replacement/Inspection After Deployment - Refer to: Airbag and Tensioner Disposal () or SRS Component Replacement/Inspection After Deployment () for a complete list of other parts that must also be replaced.

Preconditions
- 12 Volt Battery Negative Terminal Disconnect
Key Information

Do the following before starting your work.

Remove:
- Passenger's Dashboard Undercover
- Glove Box (Lower)
Sub-Procedure

Installation

NOTICE:

Before installing the glove box, make sure the SRS indicator works normally.

After Installation

1. 12 Volt Battery Negative Terminal Reconnect

2. Turn the vehicle to the ON mode, and check that the SRS indicator comes on for about 6 seconds and then goes off.
AX.-
WARNING:
- Review the precautions and procedures before doing repairs or service .
- Wait at least 3 minutes, after disconnecting the 12 volt battery terminal.
Preconditions
- 12 Volt Battery Negative Terminal Disconnected
Key Information

NOTE: For the removal and installation procedure, refer to Dashboard Removal and Installation - Refer to: Dashboard Removal and Installation () or Dashboard/Steering Hanger Beam Removal and Installation () .

Removal
- Refer to the figure.
Courtesy of HONDA, U.S.A., INC.

After Installation
- 12 Volt Battery Negative Terminal Reconnect
AY.-
WARNING:
- Review the precautions and procedures before doing repairs or service .
- Wait at least 3 minutes, after disconnecting the 12 volt battery terminal.
Preconditions
- 12 Volt Battery Negative Terminal Disconnected
Key Information

NOTE: For the removal and installation procedure, refer to Dashboard/Steering Hanger Beam Removal and Installation - Refer to: Dashboard Removal and Installation () or Dashboard/Steering Hanger Beam Removal and Installation () and the sub-procedure below.

Sub-Procedure

Removal

1. Loosen the special bolts (a) until they disengage from the threads on the hanger beam (b), and engage the inside threads of the collar bolts (c). The thread lock on the special bolts makes the special bolts and the collar bolts turn together. (Figure 1)

Figure 1

Courtesy of HONDA, U.S.A., INC.

2. Continue to loosen the special bolts to turned the collar bolts into the fixed space adjusters (d) until the collar bolts engage the adjuster brackets. This creates a gap (e) between the collar bolts and the body. (Figure 1)

3. Check that the collar bolts (f) are seated in the fixed space adjusters (g). (Figure 2)

NOTE: If either collar bolt was not seated, replace the special bolts.

Figure 2

Courtesy of HONDA, U.S.A., INC.

Figure 3

Courtesy of HONDA, U.S.A., INC.

4. Lift up the dashboard/steering hanger beam to release it from the guide pins (h, i) on the body. (Figure 3)

Installation

NOTE:
- Before reinstalling the dashboard, screw the special bolt (m) into the collar bolt (n), and check that they turn together. If they do not turn together, replace the special bolt. (Figure 4)
- Before reinstalling the dashboard, be sure the collar bolts can be screwed/unscrewed lightly by hand, and then screw them into the fixed space adjusters (o) fully by hand. Do not tighten them with any tools. (Figure 4)
- Make sure the dashboard fits onto the guide pins correctly.
- Before tightening the bolts, make sure the wire harnesses are not pinched.
- Make sure the connectors are plugged in properly.
- After setting the dashboard in the body, reinstall all of the mounting bolts but do not tighten them.
- Tighten the special bolts and the bolts to the specified torque.
- As you tighten the bolts, the collar bolts screw out of the space adjuster until they contact the body. Continue tightening the special bolts to the specified torque.
- If the bolt threads of the steering hanger beam are stripped, replace the bolts with one-size larger bolts (available as a service part), which are specifically designed to tighten the instrument panel to the specified torque setting.
- Check for any DTCs that may have been set during repairs, and clear them.
Figure 4

Courtesy of HONDA, U.S.A., INC.

After Installation
- 12 Volt Battery Negative Terminal Reconnect