LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Hummer >> 2008 >> H2 4D Utility Pickup >> Repair and Diagnosis >> Body & Frame >> Fixed And MOVEABLE Windows >> Diagnostic Information and Procedures >> Power Windows Malfunction >> Circuit/System Testing
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Circuit/System Testing

Driver Power Window Inoperative

  1. Ignition OFF, disconnect the X1 harness connector at the DDS.
  2. Test for less than 1 ohm between the ground circuit terminal 6 and ground.
    • If greater than the specified range, test the ground circuit for an open/high resistance.
  3. Ignition ON, verify that a test lamp illuminates between the B+ circuit terminal 2 and ground.
    • If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.
  4. Ignition OFF, reconnect the harness connector at the DDS.
  5. Ignition ON, observe the scan tool Driver Window Switch parameters while using the driver power window switch. The reading should change between OFF/UP/DOWN/EXPRESS DOWN.
    • If the parameter does not change, replace the DDS.
  6. Ignition OFF, disconnect the harness connector at the driver window motor.
  7. Connect a test lamp between control circuit terminal A and control circuit terminal B.
  8. Ignition ON, command the driver window UP and DOWN by using the driver window switch. The test lamp should turn ON when commanding the UP and DOWN states.
    • If the test lamp is always OFF during either of the commands, test for a short to ground or open/high resistance on either control circuit. If the circuits test normal, replace the DDS.
    • If the test lamp is always ON, test for a short to voltage on either control circuit. If the circuits test normal, replace the DDS.
  9. If all circuits test normal, test or replace the driver window motor.

Passenger Power Window Inoperative

  1. Ignition OFF, disconnect the X1 harness connector at the PDS.
  2. Test for less than 1 ohm between the ground circuit terminal 6 and ground.
    • If greater than the specified range, test the ground circuit for an open/high resistance.
  3. Ignition ON, verify that a test lamp illuminates between the B+ circuit terminal 2 and ground.
    • If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.
  4. Ignition OFF, reconnect the harness connector at the PDS.
  5. Ignition ON, observe the scan tool Passenger Window Switch parameters while using the passenger power window switch. The reading should change between OFF/UP/DOWN/EXPRESS DOWN.
    • If the parameter does not change, replace the PDS.
  6. Ignition OFF, disconnect the harness connector at the passenger window motor.
  7. Connect a test lamp between control circuit termina A and control circuit terminal B.
  8. Ignition ON, command the passenger window UP and DOWN by using the passenger window switch. The test lamp should turn ON when commanding the UP and DOWN states.
    • If the test lamp is always OFF during either of the commands, test for a short to ground or open/high resistance on either control circuit. If the circuits test normal, replace the PDS.
    • If the test lamp is always ON, test for a short to voltage on either control circuit. If the circuits test normal, replace the DDS.
  9. If all circuits test normal, test or replace the passenger window motor.

Rear Power Window Inoperative

  1. Ignition OFF, disconnect the harness connector at the appropriate rear window switch.
  2. Test for less than 1 ohm between ground and the ground circuit listed below:
    • Right rear window switch ground circuit terminal E
    • Left rear window switch ground circuit terminal F
    • If greater than the specified range, test the ground circuit for an open/high resistance.
  3. Ignition ON, verify that a test lamp illuminates between the B+ circuit terminal H and ground.
    • If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.
  4. Enable the rear windows by using the window lockout switch.
  5. Test for more than 10 volts on the control circuit terminal D.
    • If less than the specified range, test the control circuit for a short to ground or open/high resistance. If the circuit tests normal, replace the BCM.
  6. Test for more than 10 volts on the signal circuit terminal C while commanding the rear window DOWN with a scan tool.
    • If less than the specified range, test the signal circuit for a short to ground or open/high resistance. If the circuit tests normal, replace the BCM.
  7. Test for more than 10 volts on the signal circuit terminal A while commanding the rear window UP with a scan tool.
    • If less than the specified range, test the signal circuit for a short to ground or open/high resistance. If the circuit tests normal, replace the BCM.
  8. Ignition OFF, reconnect the rear window switch and disconnect the harness connector at the rear window motor
  9. Connect a test lamp between control circuit terminal A and control circuit terminal B.
  10. Ignition ON, command the rear window UP and DOWN by using the rear window switch. The test lamp should turn ON when commanding the UP and DOWN states.
    • If the test lamp is always OFF during either of the commands, test for a short to ground or open/high resistance on either control circuit. If the circuits test normal, replace the rear window switch.
    • If the test lamp is always ON, test for a short to voltage on either control circuit. If the circuits test normal, replace the rear window switch.
  11. If all circuits test normal, test or replace the rear window motor.
scientia non olet · About LEMON Manuals