Display Item List
CAUTION:
The display shows the control unit calculation data, so a normal value might be displayed even in the event the output circuit (harness) is open or short - circuited.
DISPLAY DATA MONITOR CHART
| E: ECU INPUT SIGNALS M: MAIN SIGNALS S: SELECTION FROM MENU | ||||
|---|---|---|---|---|
| SELECT MONITOR ITEM | Monitor item | Display content | Data monitor | |
| Condition | Reference value in normal operation | |||
| E, M, S | FR LH SENSOR FR RH SENSOR RR LH SENSOR RR RH SENSOR |
Wheel speed | 0 [km/h] | Vehicle stopped |
| Nearly matches the speed meter display (+/- 10 % or less) | Vehicle running (Note 1) |
|||
| E, M, S | STOP LAMP SW | Brake pedal operation | When brake pedal is depressed | ON |
| When brake pedal is not depressed | OFF | |||
| E, M, S | BATTERY VOLT | Battery voltage supplied to the ABS actuator and electric unit (control unit) | Ignition switch ON | 10 - 16 V |
| E, M, S | GEAR | Gear position determined by TCM | 1st gear 2nd gear 3rd gear 4th gear 5th gear |
1 2 3 4 5 |
| E, M, S | SLCT LVR POSI | A/T shift position | P position R position N position D position |
P R N D |
| E, M, S | OFF SW | VDC OFF switch ON/OFF | VDC OFF switch ON (When VDC OFF indicator lamp is ON) | ON |
| VDC OFF switch OFF (When VDC OFF indicator lamp is OFF) | OFF | |||
| E, M, S | YAW RATE SEN | Yaw rate detected by yaw rate/side G sensor | When vehicle stop | Approx.0 d/s |
| When vehicle turning | (-75 to 75 d/s) | |||
| E, M, S | 4WD MODE MON (Note 2) |
AWD activated | Engine running | AUTO |
| E, M, S | ACCEL POS SIG | Throttle actuator opening/closing is displayed (linked with accelerator pedal) | Accelerator pedal not depressed (ignition switch is ON) | 0 % |
| Depress accelerator pedal (ignition switch is ON) | 0 - 100 % | |||
| E, S | SIDE G-SENSOR | Transverse G detected by side G sensor | Vehicle stopped | Approx. 0 m/s2 |
| Vehicle turning right | Negative value (m/s2 ) | |||
| Vehicle turning left | Positive value (m/s2 ) | |||
| E, S | STR ANGLE SIG | Steering angle detected by steering angle sensor | Straight-ahead | Approx. 0° |
| Steering wheel turned | -720 to 720° | |||
| E, S | PRESS SENSOR | Brake fluid pressure detected by pressure sensor | With ignition switch turned ON and brake pedal released | Approx. 0 bar |
| With ignition switch turned ON and brake pedal depressed | -40 to 300 bar | |||
| E, S | ENGINE RPM | With engine running | With engine stopped | 0 rpm |
| Engine running | Almost in accordance with tachometer display | |||
| E, S | FLUID LEV SW | Brake fluid level switch | When brake fluid level switch ON | ON |
| When brake fluid level switch OFF | OFF | |||
| E, S | PARK BRAKE SW | Parking brake switch | Parking brake switch is active | ON |
| Parking brake switch is inactive | OFF | |||
| M, S | FR RH IN SOL FR RH OUT SOL FR LH IN SOL FR LH OUT SOL RR RH IN SOL RR RH OUT SOL RR LH IN SOL RR LH OUT SOL |
Operation status of all solenoid valve | Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT-II) or actuator relay is inactive (in failsafe mode) | ON |
| When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON) | OFF | |||
| M, S | MOTOR RELAY | Motor and motor relay operation | When the motor relay and motor are operating | ON |
| When the motor relay and motor are not operating | OFF | |||
| M, S | ACTUATOR RLY (Note 3) |
Actuator relay operation | When the actuator relay is operating | ON |
| When the actuator relay is not operating | OFF | |||
| M, S | ABS WARN LAMP | ABS warning lamp (Note 4) |
When ABS warning lamp is ON | ON |
| When ABS warning lamp is OFF | OFF | |||
| M, S | OFF LAMP | VDC OFF indicator lamp (Note 4) |
When VDC OFF indicator lamp is ON | ON |
| When VDC OFF indicator lamp is OFF | OFF | |||
| M, S | SLIP LAMP | SLIP indicator lamp (Note 4) |
When SLIP indicator lamp is ON | ON |
| When SLIP indicator lamp is OFF | OFF | |||
| S | 4WD FAIL REQ (Note 2) |
AWD control unit fail-safe signal | When AWD control unit is fail-safe mode | ON |
| When AWD control unit is normal | OFF | |||
| S | SNOW MODE SW | Snow mode switch | When snow mode switch is ON | ON |
| When snow mode switch is OFF | OFF | |||
| S | BST OPER SIG | Not applied but displayed | - | OFF |
| S | M-MODE SIG | Manual mode activated | When the manual mode is active | ON |
| When the manual mode is inactive | OFF | |||
| S | EBD SIGNAL | EBD operation | EBD is active | ON |
| EBD is inactive | OFF | |||
| S | ABS SIGNAL | ABS operation | ABS is active | ON |
| ABS is inactive | OFF | |||
| S | TCS SIGNAL | TCS operation | TCS is active | ON |
| TCS is inactive | OFF | |||
| S | VDC SIGNAL | VDC operation | VDC is active | ON |
| VDC is inactive | OFF | |||
| S | EBD FAIL SIG | EBD fail-safe signal | In EBD fail-safe | ON |
| EBD is normal | OFF | |||
| S | ABS FAIL SIG | ABS fail-safe signal | In ABS fail-safe | ON |
| ABS is normal | OFF | |||
| S | TCS FAIL SIG | TCS fail-safe signal | In TCS fail-safe | ON |
| TCS is normal | OFF | |||
| S | VDC FAIL SIG | VDC fail-safe signal | In VDC fail-safe | ON |
| VDC is normal | OFF | |||
| S | CRANKING SIG | Crank operation | Crank is active | ON |
| Crank is inactive | OFF | |||
| S | USV HSV (FL-RR, FR-RL) (Note 3) | VDC switch-over valve | When actuator (switchover valve) is active ("ACTIVE TEST" with CONSULT-II) or actuator relay is inactive (when in fail-safe mode) | ON |
| When actuator (switchover valve) is not active and actuator relay is active (ignition switch ON) | OFF | |||
| S | V/R OUTPUT (Note 3) |
Solenoid valve relay activated | When the solenoid valve relay is active (When ignition switch OFF) | ON |
| When the solenoid valve relay is not active (in the fail-safe mode) | OFF | |||
| S | M/R OUTPUT | Actuator motor and motor relay activated | When the actuator motor and motor relay are active ("ACTIVE TEST" with CONSULT-II) | ON |
| When the actuator motor and motor relay are inactive | OFF | |||
| Note 1: Confirm tire pressure is normal. Note 2: Only AWD model. Note 3: A brief moment of ON/OFF condition occurs every 20 seconds after ignition switch turned ON. This is not malfunction because it is an operation for checking. Note 4: On and off timing for warning lamp and indicator lamp. Refer to "ON AND OFF TIMING FOR WARNING LAMP AND INDICATOR LAMP ". |
||||