Reference Value From Consult-II
CAUTION:
The display shows ABS actuator and electric unit (control unit) calculation data, so a normal value might be displayed even in the event the output circuit (harness) is open or short-circuited.
CONTROL UNIT INPUT/OUTPUT SIGNAL
| Monitor item | Display content | Data monitor | |
|---|---|---|---|
| Condition | Reference value in normal operation | ||
| SLCT LVR POSI | A/T shift position | P: P position R: R position N: N position D: D position |
|
| GEAR | A/T gear position | 1: 1st gear 2: 2nd gear 3: 3rd gear 4: 4th gear 5: 5th gear |
|
| FR RH SENSOR FR LH SENSOR RR RH SENSOR RR LH SENSOR |
Wheel speed | Vehicle stopped | 0 [km/h (MPH)] |
| Vehicle running (Note 1) | Almost in accordance with speedometer display (within ± 10 %) | ||
| ACCEL POS SIG | Open/close condition of throttle valve (linked with accelerator pedal) | Accelerator pedal not depressed (Engine stopped) | 0 % |
| Depress accelerator pedal (Engine stopped) | 0 to 100 % | ||
| ENGINE SPEED | With engine running | With engine stopped | 0 rpm |
| Engine running | Almost in accordance with tachometer display | ||
| STR ANGLE SIG | Steering angle detected by steering angle sensor | Straight-ahead | Approx. 0 deg |
| Steering wheel turned | -756 to 756 deg | ||
| YAW RATE SEN | Yaw rate detected by yaw rate sensor | Vehicle stopped | Approx. 0 d/s |
| Vehicle running | -100 to 100 d/s | ||
| SIDE G-SENSOR | Transverse G detected by side G sensor | Vehicle stopped | Approx. 0 m/s2 |
| Vehicle running | -16.7 to 16.7 m/s2 | ||
| PRESS SENSOR | Brake fluid pressure detected by pressure sensor | With ignition switch turned ON and brake pedal released | Approx. 0 bar |
| With ignition switch turned ON and brake pedal depressed | 0 to 170 bar | ||
| BATTERY VOLT | Battery voltage supplied to ABS actuator and electric unit (control unit) | Ignition switch ON | 10 to 16 V |
| STOP LAMP SW | Brake pedal operation | Brake pedal depressed | ON |
| Brake pedal not depressed | OFF | ||
| OFF SW | VDC OFF switch ON/OFF status | VDC OFF switch ON (When VDC OFF indicator lamp is ON) | ON |
| VDC OFF switch OFF (When VDC OFF indicator lamp is OFF) | OFF | ||
| ABS WARN LAMP | ABS warning lamp ON condition (Note 2) | ABS warning lamp ON | ON |
| ABS warning lamp OFF | OFF | ||
| MOTOR RELAY | Operation status of motor and motor relay | Ignition switch ON or engine running (ABS not operated) | OFF |
| Ignition switch ON or engine running (ABS operated) | ON | ||
| ACTUATOR RLY | Actuator relay operation status | Actuator (solenoid) is active ("ACTIVE TEST" with CONSULT-II) | ON |
| When actuator relay is inactive (in fail-safe mode) | OFF | ||
| OFF LAMP | VDC OFF indicator lamp status (Note 3) | When VDC OFF indicator lamp is ON | ON |
| When VDC OFF indicator lamp is OFF | OFF | ||
| SLIP LAMP | SLIP indicator lamp status (Note 4) | When SLIP indicator lamp is ON | ON |
| When SLIP indicator lamp is OFF | OFF | ||
| FR LH IN SOL FR LH OUT SOL FR RH IN SOL FR RH OUT SOL RR RH IN SOL RR RH OUT SOL RR LH IN SOL RR LH OUT SOL |
Solenoid valve operation | Actuator (solenoid) is active ("ACTIVE TEST" with CONSULT-II) and actuator relay is active (ignition switch ON) | ON |
| When actuator (solenoid) is not active or actuator relay is inactive (in fail-safe mode) | OFF | ||
| CV1 CV2 SV1 SV2 |
VDC/TCS switch-over valve status | When actuator (switch-over valve) is active ("ACTIVE TEST" with CONSULT-II) and actuator relay is active (ignition switch ON) | ON |
| When actuator (switch-over valve) is not active or actuator relay is inactive (in fail-safe mode) | OFF | ||
| DECEL G-SEN | Longitudinal acceleration detected by decel G sensor (Note 5) | Vehicle stopped | Approx. 0 G |
| Vehicle running | -1.7 to +1.7 G | ||
| FLUID LEV SW | ON/OFF status of brake fluid level switch | When brake fluid level switch ON | ON |
| When brake fluid level switch OFF | OFF | ||
| VDC FAIL SIG TCS FAIL SIG ABS FAIL SIG EBD FAIL SIG |
Fail signal status | VDC fail TCS fail ABS fail EBD fail |
ON |
| VDC normal TCS normal ABS normal EBD normal |
OFF | ||
| EBD WARN LAMP | Brake warning lamp on condition (Note 6) | Brake warning lamp ON | ON |
| Brake warning lamp OFF | OFF | ||
| EBD SIGNAL | EBD operation | EBD active | ON |
| EBD not active | OFF | ||
| ABS SIGNAL | ABS operation | ABS active | ON |
| ABS not active | OFF | ||
| TCS SIGNAL | TCS operation | TCS active | ON |
| TCS not active | OFF | ||
| VDC SIGNAL | VDC operation | VDC active | ON |
| VDC not active | OFF | ||
| CRANKING SIG | CRANKING status | Cranking | ON |
| Not cranking | OFF | ||
| 4WD FAIL REQ | ETS fail status (Note 5) | ETS fail | ON |
| ETS normal | OFF | ||
| 2WD/4WD | Drive axle | 2WD model | 2WD |
| AWD model | AWD | ||
| Note 1: Confirm tire pressure is normal. Note 2: ON/OFF timing of ABS warning lamp ON: Approx. Within 2 seconds after ignition switch is turned ON, or when a malfunction is detected. OFF: Approx. 2 seconds after ignition switch is turned ON (when system is in normal operation) and VDC/TCS function is not activated. Note 3: ON/OFF timing of VDC OFF indicator lamp ON: Approx. Within 2 seconds after ignition switch is turned ON, or when a malfunction is detected and VDC OFF switch is ON. OFF: Approx. 2 seconds after ignition switch is turned ON (when system is in normal operation.) And when VDC OFF switch is OFF. Note 4: ON/OFF timing of SLIP indicator lamp ON: Approx. Within 2 seconds after ignition switch is turned ON, or when a malfunction is detected and VDC/TCS function is activated while driving. OFF: Approx. 2 seconds after ignition switch is turned ON (when system is in normal operation) and VDC/TCS function is not activated. Flashing: VDC/TCS function is active during driving Note 5: Only AWD models. Note 6: Serves as EBD warning lamp. |
|||