Diagnostic Procedure

SYMPTOM 1: 

• Selector lever cannot be moved from "P" position with key in ON position and brake pedal applied. 
• Selector lever can be moved from "P" position with key in ON position and brake pedal released. 
• Selector lever can be moved from "P" position when key is removed from key cylinder. 

  SYMPTOM 2: 

• Ignition key cannot be removed when selector lever is set to "P" position. 
• Ignition key can be removed when selector lever is set to any position except "P" position. 

1. CHECK KEY INTERLOCK CABLE 

   Check the key interlock cable for damage.

   OK or NG 

   OK: GO TO 2.

   NG: Repair or replace key interlock cable. Refer to "KEY INTERLOCK CABLE ".

2. CHECK SELECTOR LEVER POSITION 

   Check the selector lever position for damage. Refer to "CHECKING OF A/T POSITION "

   OK or NG 

   OK: GO TO 3.

   NG: Adjust A/T position. Refer to "ADJUSTMENT OF A/T POSITION ".

3. CHECK SHIFT LOCK SOLENOID AND PARK POSITION SWITCH 
   1. Connect A/T device harness connector.
   2. Turn ignition switch ON.
   3. Selector lever is set in "P" position.
   4. Check operation.
   BRAKE PEDAL CONDITION CHART
   
   

   Condition	Brake pedal	Operation
   When ignition switch is turned to ON and selector lever is set in "P" position.	Depressed	Yes
   	Released	No

   OK or NG 

   OK: INSPECTION END 

   NG: GO TO 4.

4. CHECK POWER SOURCE 
   1. Turn ignition switch ON.
   2. Check the voltage between A/T device harness connector M67 terminal 1 and ground. Refer to "WIRING DIAGRAM - AT - SHIFT ".
   Fig 1: Identifying Voltage Between A/T Device Harness Connector M67 Terminal 1 And Ground
   Courtesy of NISSAN MOTOR CO., U.S.A.
   BRAKE PEDAL CONDITION CHART
   
   

   Condition	Brake pedal	Data (Approx.)
   When ignition switch is turned to ON.	Depressed	Battery voltage
   	Released	0 V

   OK or NG 

   OK: GO TO  7.

   NG: GO TO 5.

5. CHECK STOP LAMP SWITCH 
   1. Turn ignition switch OFF.
   2. Disconnect stop lamp switch harness connector.
   3. Check continuity between stop lamp switch harness connector E210 terminals 3 and 4.
   Fig 2: Identifying Continuity Between Stop Lamp Switch Connector Terminals
   Courtesy of NISSAN MOTOR CO., U.S.A.
   STOP LAMP SWITCH
   
   

   Condition	Continuity
   When brake pedal is depressed	Yes
   When brake pedal is released	No

   Check stop lamp switch after adjusting brake pedal - refer to  "BRAKE PEDAL ".

   OK or NG 

   OK: GO TO 6.

   NG: Repair or replace damaged parts.

6. DETECT MALFUNCTIONING ITEM 

   Check the following items. If any items are damaged, repair or replace damaged parts.

   • Harness for short or open between ignition switch and stop lamp switch harness connector E210 terminal 3.
   • Harness for short or open between stop lamp switch harness connector E210 terminal 4 and A/T device harness connector M67 terminal 1.
   • 10 A fuse [No.12, located in the fuse block (J/B)].
   • Ignition switch, Refer to "POWER SUPPLY ROUTING CIRCUIT ".

   OK or NG 

   OK: INSPECTION END 

   NG: Repair or replace damaged parts.

7. CHECK GROUND CIRCUIT 
   1. Turn ignition switch OFF.
   2. Disconnect A/T device harness connector.
   3. Check continuity between A/T device harness connector M67 terminal 2 and ground.

      Continuity should exist. 

   Fig 3: Identifying Continuity Between A/T Device Harness Connector M47 Terminal 2 And Ground

   Courtesy of NISSAN MOTOR CO., U.S.A.

   OK or NG 

   OK: Replace shift lock solenoid and park position switch assembly.

   NG: Repair open circuit in harness or connectors.