Reference Value From Consult-II
CAUTION:
The display shows ABS actuator and electric unit (control unit) calculation data, so a normal value might be displayed even in the event the output circuit (harness) is open or short-circuited.
CALCULATION DATA REFERENCE
| Monitor item | Display content | Data monitor | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| Condition | Reference value in normal operation | ||||||||||
| FR LH SENSOR FR RH SENSOR RR LH SENSOR RR RH SENSOR |
Wheel speed | Vehicle stopped | 0 [km/h (MPH)] | ||||||||
| Vehicle running ((1)) | Nearly matches the speedometer display (± 10 % or less) | ||||||||||
| STOP LAMP SW | Brake pedal operation | When brake pedal is depressed | ON | ||||||||
| When brake pedal is not depressed | OFF | ||||||||||
| BATTERY VOLT | Battery voltage supplied to the ABS actuator and electric unit (control unit) | Ignition switch ON | 10 - 16 V | ||||||||
| GEAR | Gear position determined by TCM | 1st gear | 1 | ||||||||
| 2st gear | 2 | ||||||||||
| 3rd gear | 3 | ||||||||||
| 4th gear | 4 | ||||||||||
| 5th gear | 5 | ||||||||||
| SLCT LVR POSI | A/T select lever position | P position | P | ||||||||
| R position | R | ||||||||||
| N position | N | ||||||||||
| D position | D | ||||||||||
| OFF SW | VDC OFF switch | VDC OFF switch :ON (When VDC OFF indicator lamp is ON) |
ON | ||||||||
| VDC OFF switch :OFF (When VDC OFF indicator lamp is OFF) |
OFF | ||||||||||
| YAW RATE SEN | Yaw rate detected by yaw rate/side G sensor | When vehicle stop Approx. | 0 d/s | ||||||||
| When vehicle turning | (-75 to 75 d/s) | ||||||||||
| 4WD MODE MON ((2)) | AWD activated | Engine running | AUTO | ||||||||
| ACCEL POS SIG | Throttle actuator opening/closing is displayed (linked with accelerator pedal) | Accelerator pedal not depressed (Engine stopped) | 0 % | ||||||||
| Depress accelerator pedal (Engine stopped) | 0 - 100 % | ||||||||||
| SIDE G-SENSOR | Transverse G detected by side G sensor | Vehicle stopped | Approx. 0 m/s2 | ||||||||
| Vehicle turning right | Negative value (m/s2 ) | ||||||||||
| Vehicle turning left | Positive value (m/s2 ) | ||||||||||
| STR ANGLE SIG | Steering angle detected by steering angle sensor | Straight-ahead | Approx. 0° | ||||||||
| Steering wheel turned | -720 to 720° | ||||||||||
| PRESS SENSOR | Brake fluid pressure detected by pressure sensor | With ignition switch turned ON and brake pedal released | Approx. 0 bar | ||||||||
| With ignition switch turned ON and brake pedal depressed | -40 to 300 bar | ||||||||||
| ENGINE RPM | Engine speed | With engine stopped | 0 rpm | ||||||||
| Engine running | Almost in accordance with tachometer display | ||||||||||
| FLUID LEV SW | Brake fluid level switch | Brake fluid level switch ON | ON | ||||||||
| Brake fluid level switch OFF | OFF | ||||||||||
| PARK BRAKE SW | Parking brake switch | Parking brake switch is active | ON | ||||||||
| Parking brake switch is inactive | OFF | ||||||||||
| FR RH IN SOL FR RH OUT SOL FR LH IN SOL FR LH OUT SOL RR RH IN SOL RR RH OUT SOL RR LH IN SOL RR LH OUT SOL |
Operation status of all solenoid valve | Actuator (solenoid valve) is active ("ACTIVE TEST" with CONSULT-II) or actuator relay is inactive (in fail-safe mode) | ON | ||||||||
| When the actuator (solenoid valve) is not active and actuator relay is active (ignition switch ON) | OFF | ||||||||||
| MOTOR RELAY | Motor and motor relay operation | When the motor relay and motor are operating | ON | ||||||||
| When the motor relay and motor are not operating | OFF | ||||||||||
| ACTUATOR RLY ((3)) | Actuator relay operation | When the actuator relay is operating | ON | ||||||||
| When the actuator relay is not operating | OFF | ||||||||||
| ABS WARN LAMP | ABS warning lamp ((4)) | When ABS warning lamp is ON | ON | ||||||||
| When ABS warning lamp is OFF | OFF | ||||||||||
| OFF LAMP | VDC OFF indicator lamp ((4)) | When VDC OFF indicator lamp is ON | ON | ||||||||
| When VDC OFF indicator lamp is OFF | OFF | ||||||||||
| SLIP LAMP | SLIP indicator lamp ((4)) | When SLIP indicator lamp is ON | ON | ||||||||
| When SLIP indicator lamp is OFF | OFF | ||||||||||
| 4WD FAIL REQ ((2)) | AWD control unit fail-safe signal | When AWD control unit is fail-safe mode | ON | ||||||||
| When AWD control unit is normal | OFF | ||||||||||
| SNOW MODE SW | Snow mode switch | When snow mode switch is ON | ON | ||||||||
| When snow mode switch is OFF | OFF | ||||||||||
| BST OPER SIG | Not applied but displayed | - | OFF | ||||||||
| M-MODE SIG | Manual mode operation | When the manual mode is active | ON | ||||||||
| When the manual mode is inactive | OFF | ||||||||||
| EBD SIGNAL | EBD operation | EBD is active | ON | ||||||||
| EBD is inactive | OFF | ||||||||||
| ABS SIGNAL | ABS operation | ABS is active | ON | ||||||||
| ABS is inactive | OFF | ||||||||||
| TCS SIGNAL | TCS operation | TCS is active | ON | ||||||||
| TCS is inactive | OFF | ||||||||||
| VDC SIGNAL | VDC operation | VDC is active | ON | ||||||||
| VDC is inactive | OFF | ||||||||||
| EBD FAIL SIG | EBD fail-safe signal | In EBD fail-safe | ON | ||||||||
| EBD is normal | OFF | ||||||||||
| ABS FAIL SIG | ABS fail-safe signal | In ABS fail-safe | ON | ||||||||
| ABS is normal | OFF | ||||||||||
| TCS FAIL SIG | TCS fail-safe signal | In TCS fail-safe | ON | ||||||||
| TCS is normal | OFF | ||||||||||
| VDC FAIL SIG | VDC fail-safe signal | In VDC fail-safe | ON | ||||||||
| VDC is normal | OFF | ||||||||||
| CRANKING SIG | Crank operation | Crank is active | ON | ||||||||
| Crank is inactive | OFF | ||||||||||
| USV[FR-RL] USV[FL-RR] HSV[FR-RL] HSV[FL-RR] ((3)) |
VDC switch-over valve | When actuator (switch-over valve) is active ("ACTIVE TEST" with CONSULT-II) or actuator relay is inactive (when in fail-safe mode) | ON | ||||||||
| When actuator (switch-over valve) is not active and actuator relay is active (ignition switch ON) | OFF | ||||||||||
| V/R OUTPUT ((3)) | Solenoid valve relay activated | When the solenoid valve relay is active | ON | ||||||||
| When the solenoid valve relay is not active (in the fail-safe mode) | OFF | ||||||||||
| M/R OUTPUT | Actuator motor and motor relay activated | When the actuator motor and motor relay are active ("ACTIVE TEST" with CONSULT-II) | ON | ||||||||
| When the actuator motor and motor relay are inactive | OFF | ||||||||||
|
NOTE:
|
|||||||||||